Age | Commit message (Collapse) | Author |
|
Add uart2 DTE pin group for DTE test.
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
|
|
increase CMA size to 160MB to fix cma alloc failure for v4l2 capture case:
Capture_To_Display_mmap: mode 6(2592x1944)@15fps test.
...
[ 247.301290] cma: cma_alloc: alloc failed, req-size: 2461 pages, ret: -12
[ 247.308290] mx6s-csi 21c4000.csi: dma_alloc_coherent of size 10080256 failed
[ 247.317097] cma: cma_alloc: alloc failed, req-size: 2461 pages, ret: -12
...
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
(cherry picked from commit 1b0a2c9d50ac0d441243f0a2e88760c7e1e7b5ef)
|
|
imx6ul Rev1.2 with 14x14 evk revC board required to increase
SD1_CLK pin drive strength. So update usdhc1 pin group for
imx6ul-14x14-evk to avoid crc error.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
|
|
imx6ul/ull/ulz 14x14 evk board memory size is 512M, current
board dts set CMA reserved memory size to 320M, which causes
system has no free memory for unmovable and reclaimable.
In fact, set CMA memory size to 96M is large enough for pxp and
epdc cases.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
|
|
Without this "jedec,spi-nor" compatible property, probing of the SPI NOR
does not work on the NXP i.MX6ULL EVK. Fix this by adding this
compatible property to the DT.
Fixes: 7d77b8505aa9 ("ARM: dts: imx6ull: fix the imx6ull-14x14-evk configuration")
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Shawn Guo <shawnguo@kernel.org>
|
|
Reserve CMA memory for GPU/MM/Display
[ Aisheng: Ported from 4.19 GA ]
Tested-by: Robby Cai <robby.cai@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
|
|
After commit f7907e57aea2 ("regulator: fixed: add off-on-delay"), user
can use "off-on-delay-us" to define the regulator off-delay time.
For SD card, according to the spec requirement, for sd card power reset
operation, it need sd card supply voltage to be lower than 0.5v and keep
over 1ms, otherwise, next time power back the sd card supply voltage to
3.3v, sd card can't support SD3.0 mode again.
This patch add the off-on-delay-us to each board, make sure the sd power
reset behavior is align with the specification. Without this patch, when
do quick system suspend/resume test, some sd card can't work at SD3.0 mode
after system resume back.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Leonard Crestez <leonard.crestez@nxp.com>
|
|
Without configuring this pinctrl, the ID value can't be got correctly,
then, the dual-role switch can't work well.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
property for CAN
pinctrl-assert-gpios and registers-default, these properties does not exist
in upstream, need add back.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
(cherry picked from commit 8492eb228a80712059d1873c613954b180f009ae)
|
|
add parallel camera ov5640 support on imx6ul/imx6ull 14x14 EVK.
Signed-off-by: Robby Cai <robby.cai@nxp.com>
|
|
currently we still use internal framebuffer driver for lcdif.
remove DRM-specific staff to avoid conflict.
Signed-off-by: Robby Cai <robby.cai@nxp.com>
|
|
enable PXP V4L2 driver on imx6ul 14x14 EVK
Signed-off-by: Robby Cai <robby.cai@nxp.com>
|
|
Support audio sound card (wm8960)
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
|
|
Add sensors nodes in dts files for tests.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
|
|
Add emmc support for imx6ull-14x14-evk and imx6ul-14x14-evk board
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
|
|
Add SIM device node.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
|
|
A few boards set clock frequency of their I2C buses with
"clock_frequency" property. The right property is "clock-frequency".
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
We will move the FSL QSPI driver to the SPI framework soon. To
prepare and to make sure the full buswidth is used (as it is with
the current driver), let's add the right properties.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add flexcan support for i.MX6UL board. Change the place of CAN node delete
due to i.MX6ULZ include i.MX6UL dts but not support flexcan.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Most of the i.MX NXP reference board dts files have already been
converted, so switch the remaining ones.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Boards based on imx6ul have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx6ul.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
imx6ull-14x14-evk.dts currently includes the imx6ul.dtsi file for an
i.MX6ULL SoC which is plain wrong.
Rename the current imx6ul-14x14-evk.dts to .dtsi and include it from
imx6ul-14x14-evk.dts and imx6ull-14x14-evk.dts, so that both can
include the appropriate SoC specific (imx6ul.dtsi/imx6ull.dtsi) file.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|