Age | Commit message (Collapse) | Author |
|
Keep +3.3V pull-ups interface by default in imx6ull-colibri.dtsi
SD card interface setting per board device tree:
imx6ull-colibri-aster.dtsi +3.3V pull-ups
imx6ull-colibri-eval-v3.dtsi +3.3V pull-ups
imx6ull-colibri-iris.dtsi +3.3V pull-ups
imx6ull-colibri-iris-v2.dtsi +1.8V signaling, UHS capable
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
For imx6ull none-emmc device trees enable:
- MXT TS over adapter or connector (board dependent);
- ad7879 support;
- Parallel RGB/VGA capability.
Related-to: ELB-4065
|
|
Move all atmel and fusion touchscreen nodes from board-level
to the main module DT. Prepare the DTs for
use with atmel mxt overlays, adding required pinmux groups.
The common scheme of pin groups for TS overlays:
- pinctrl_atmel_conn - SODIMM 106/107 pins for INT/RST (default)
- pinctrl_atmel_adap - SODIMM 28/30 pins for INT/RST signals.
Related-to: ELB-3868
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
Move parallel-rgb interface into separate module tree
imx6ull-colibri-lcdif.dtsi. Keep lcdif, backlight
and pwm4 disabled by default.
Related-to: ELB-3244
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
iMX6ULL NAND modules do not specify overlay scheme
to enable Atmel device on Capacitive Touchscreen.
Keep Atmel device nodes enabled for Evaluation board,
Aster and Iris.
Related-to: ELB-3868
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
All Toradex Colibri family boards support the ecspi interface.
Move the definition of spidev0 to the module devicetree and enable
it by default.
Colibri Eval board has a CAN SPI controller. Disable the spidev0
for this board to have the CAN controller been enabled by default.
Colibri Aster board supports 2 spidev interfaces. Enable both of them
and fix the CS configuration.
Related-to: ELB-3401
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Cosmetic change: Rename the reg_sd1_vmmc to reg_sd1_vqmmc as it is
used for vqmmc.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
(cherry picked from commit 838d16630594b3fd69a13b6e1d19ee55ec93a841)
|
|
This commit unifys the backlight settings. All displays sold by Toradex
are now supporting 150Hz as a PWM backlight typical frequency.
Use this value for all SoM's and put also some better default values
for different brightness.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
(cherry picked from commit 0f2115c3c8934714e88a768ace4c324d08ac9039)
Conflicts:
arch/arm64/boot/dts/freescale/fsl-imx8qm-apalis.dts
arch/arm64/boot/dts/freescale/fsl-imx8qxp-colibri-aster.dts
arch/arm64/boot/dts/freescale/fsl-imx8qxp-colibri-eval-v3.dtsi
arch/arm64/boot/dts/freescale/fsl-imx8qxp-colibri-lvds-dual-eval-v3.dts
arch/arm64/boot/dts/freescale/fsl-imx8qxp-colibri-lvds-single-eval-v3.dts
arch/arm64/boot/dts/freescale/fsl-imx8qxp-colibri.dtsi
Do not apply this patch on imx8 dts, as I will pull them in separately
later on.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
According to manual of I2C bus, both signals sda/scl are "open drain".
Fix flags for all affected Toradex boards.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
(cherry picked from commit c87aa86c2d8fbfb0e0e5f6784e99402316fbb966)
Conflicts:
arch/arm/boot/dts/imx7-colibri.dtsi
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
While at it, add the dtbs for Aster Carrier Board to the Makefile.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
(cherry picked from commit 48d236e07b708f9cf9332d568f4ef02b8bbd31d6)
|
|
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
(cherry picked from commit 1a31a12c32bf2fa0ed79fe9dede489f0a0b2f5e0)
|