Age | Commit message (Collapse) | Author |
|
For imx6ull none-emmc device trees enable:
- MXT TS over adapter or connector (board dependent);
- ad7879 support;
- Parallel RGB/VGA capability.
Related-to: ELB-4065
|
|
NXP and AzureWave don't recommend using SDIO bus mode 3.3V@50MHz due
to noise affecting the wireless throughput. Colibri iMX6ULL uses only
3.3V signaling for Wi-Fi module AW-CM276NF.
Limit the SDIO Clock on Colibri iMX6ULL to 25MHz.
Related-to: ELB-4005
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Move all atmel and fusion touchscreen nodes from board-level
to the main module DT. Prepare the DTs for
use with atmel mxt overlays, adding required pinmux groups.
The common scheme of pin groups for TS overlays:
- pinctrl_atmel_conn - SODIMM 106/107 pins for INT/RST (default)
- pinctrl_atmel_adap - SODIMM 28/30 pins for INT/RST signals.
Related-to: ELB-3868
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
Add GPIO line names on module level. Those are all GPIOs which a user
might use on his custom carrier board. If more meaningful names are
available on the carrier board, the user can overwrite the line names
in the carrier board level device tree.
Related-to: ELB-2794
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
(cherry picked from commit 59ff254068f0e3638224004081704662d22b1a98)
|
|
The driver mwifiex_sdio stucks after the wifi firmware crash.
Enabling asynchronous interrupts processing in sdio driver
fixes this issue and allows the mwifiex_sdio driver to be reloaded
and continue operates successfully.
Works better with the driver from the backported-5.4 package.
Related-to: ELB-2596
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
(cherry picked from commit a6e1405c7e182522487540513fabe3a83721d980)
|
|
In 4.14 devicetress are based on the mainline DT's and only necessary
stuff for downstream is put into those devicetrees.
This commit holds the changes for imx6ull*colibri* from 4.9.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
(cherry picked from commit 2b1fa08bf92d264028e15a14a052a63f8380da65)
Conflicts:
arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
arch/arm/boot/dts/imx6ull-colibri.dtsi
Squashed commit 'ARM: dts: imx6ull-colibri: add missing #endif' into
this one.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Add the pinmuxing and a inactive node for flexcan1 on SODIMM 55/63
and move the inactive flexcan modes to imx6ull-colibri-eval-v3.dtsi
where they belong.
Note that this commit does not enable flexcan functionality, but rather
eases the effort needed to do so.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
(cherry picked from commit 983ff8a6b61e9466beb6b4781fb370a6a7da937a)
Conflicts:
arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi
arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
arch/arm/boot/dts/imx6ull-colibri.dtsi
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com
(cherry picked from commit 169685c139d72eee36914727cd4405fee4c2ee9b)
|
|
Boards based on imx6ul have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx6ul.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX6ULL has different operating ranges than i.MX6UL so add the
operating points for the i.MX6ULL and remove them from board device
trees. A 25mV offset is added to the minimum allowed values like for the
i.MX6UL.
The valid frequencies are now selected by the cpufreq driver according
to ratings stored in fuses since commit 0aa9abd4c212 ("cpufreq: imx6q:
check speed grades for i.MX6ULL")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pass the memory unit-adress to fix the following build warnings with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
There are cases where dts passes an empty memory node, which will be filled
by the bootloader. Passing the memory base address still allows the
bootloader to fill the memory size.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the Computer on Module Colibri iMX6ULL and its
Bluetooth/Wifi variant along with the development/evaluation carrier
board device trees. Follow the usual hierarchic include model,
maintaining shared configuration in imx6ull-colibri.dtsi and
imx6ull-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|