Age | Commit message (Collapse) | Author |
|
Keep +3.3V pull-ups interface by default in SOM DTSI imx7-colibri.dtsi
SD card interface setting per board device tree:
imx7-colibri-aster.dtsi +3.3V pull-ups
imx7-colibri-eval-3.dtsi +3.3V pull-ups
imx7-colibri-iris.dtsi +3.3V pull-ups
imx7-colibri-iris-v2.dtsi 1.8V signaling, no pull-ups, UHS capable
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
It is more natural to keep disabled all display stuff for eMMC modules,
which support overlays, and enable the display subsystems for NAND
modules by default.
It reduces the code and make it easier to understand.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Use Atmel and Fusion nodes for touchscreen controller
Add pinctl iomux for and adapter(SODIMM_28,SODIMM_30)
and a connector (SODIMM_106,SODIMM_107).
Related-to: ELB-3547
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
|
|
The parallel RGB interface (lcdif) and all related stuff turn
on in an overlay. Keep them disabled in the main devicetree.
As these subsystems are provided by module and not a part of boards,
move their definitions into the module-level devicetree.
Related-to: ELB-3395
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Shrink boilerplace licenses and update copyright information.
Related-to: ELB0-3395
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
All Toradex Colibri family boards support the ecspi interface.
Move the definition of spidev0 to the module devicetree and enable
it by default.
Colibri Eval board has a CAN SPI controller. Disable the spidev0
for this board to have the CAN controller been enabled by default.
Related-to: ELB-3401
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The pin GPIO1_IO01 externally pulls down, it is required to sequentially
connect this pin (signal WAKE_MICO#) to +3v3 and then disconnect it to
trigger a wakeup interrupt.
Adding the flag GPIO_PULL_DOWN allows the system to be woken up just
connecting the pin GPIO1_IO01 to +3v3.
Related-to: ELB-2901
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
This commit unifys the backlight settings. All displays sold by Toradex
are now supporting 150Hz as a PWM backlight typical frequency.
Use this value for all SoM's and put also some better default values
for different brightness.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
(cherry picked from commit 0f2115c3c8934714e88a768ace4c324d08ac9039)
Conflicts:
arch/arm64/boot/dts/freescale/fsl-imx8qm-apalis.dts
arch/arm64/boot/dts/freescale/fsl-imx8qxp-colibri-aster.dts
arch/arm64/boot/dts/freescale/fsl-imx8qxp-colibri-eval-v3.dtsi
arch/arm64/boot/dts/freescale/fsl-imx8qxp-colibri-lvds-dual-eval-v3.dts
arch/arm64/boot/dts/freescale/fsl-imx8qxp-colibri-lvds-single-eval-v3.dts
arch/arm64/boot/dts/freescale/fsl-imx8qxp-colibri.dtsi
Do not apply this patch on imx8 dts, as I will pull them in separately
later on.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
(cherry picked from commit ec4c646d6456a13fafb0e0d76dd60f418207a241)
|