| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 57dbe558457bf4042169bc1f334e3b53a8480a1c ]
The Ethernet PHY on the Bananapi M3 and Cubietruck Plus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 039359948a4b ("ARM: dts: sun8i: a83t: Enable Ethernet on two boards")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-6-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
The Bananapi M3 and Cubietruck Plus both have USB OTG ports wired to the
SoC and PMIC in the same way, with the N_VBUSEN pin on the PMIC
controlling VBUS output, the PMIC's VBUS input for sensing VBUS, and
PH11 on the SoC for sensing the ID pin.
Enable OTG on both boards.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
On the Bananapi M3 and Cubietruck Plus, the DC input jacks are wired to
the ACIN pins, which is represented by the AC power supply. Both boards
have connectors for LiPo batteries, which are represented by the battery
power supply.
The H8 Homlet is a set-top box design. The DC input jack is wired to the
ACIN pins, but there are no battery connectors.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
|
|
This patch adds the Bluetooth node, and the underlying UART node if it's
missing, to the board device tree file for several boards. The LPO clock
is also added to the WiFi side's power sequencing node if it's missing,
to correctly represent the shared connections. There is also a PCM
connection for Bluetooth, but this is not covered in this patch.
These boards all have a WiFi+BT module from AMPAK, which contains one or
two Broadcom chips, depending on the model. The older AP6210 contains
two, while the newer AP6212 and AP6330 contain just one, as they use
two-in-one combo chips.
The Bluetooth side of the module is always connected to a UART on the
same pingroup as the SDIO pins for the WiFi side, in a 4 wire
configuration. Power to the VBAT and VDDIO pins are provided either by
the PMIC, using one or several of its regulator outputs, or other fixed
regulators on the board. The VBAT and VDDIO pins are shared with the
WiFi side, which would correspond to vmmc-supply and vqmmc-supply in the
mmc host node. A clock output from the SoC or the external X-Powers RTC
provides the LPO low power clock at 32.768 kHz.
All the boards covered in this patch are ones that do not require extra
changes to the SoC's dtsi file. For the remaining boards that I have
worked on, properties or device nodes for the LPO clock's source are
missing.
For the Cubietruck, the LPO clock is fed from CLK_OUT_A, which needs to
be muxed on pin PI12. This can be represented in multiple ways. This
patch puts the pinctrl property in the pin controller node. This is due
to limitations in Linux, where pinmux settings, even the same one, can
not be shared by multiple devices. Thus we cannot put it in both the
WiFi and Bluetooth device nodes. Putting it the CCU node is another
option, but Linux's CCU driver does not handle pinctrl. Also the pin
controller is guaranteed to be initialized after the CCU, when clocks
are available. And any other devices that use muxed pins are guaranteed
to be initialized after the pin controller. Thus having the CLK_OUT_A
pinmux reference be in the pin controller node is a good choice without
having to deal with implementation issues.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Since commit d7c5f6863550 ("ARM: dts: sun8i: a83t: bananapi-m3: Add
AXP813 regulator nodes") my BPIM3 no longer works at gigabit speed.
With the default setting, dldo3 is regulated at 2.9v which seems
sufficient for the PHY but the aforementioned commit drops it to 2.5V
which is insufficient. Note that this behaviour is random for all BPIM3.
Some work with 2.5V, but some don't.
Finnaly, someone from Bananapi confirmed that this regulator must be set
to 3.3V.
Fixes: d7c5f6863550 ("ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813
regulator nodes")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
[wens@csie.org: Reworked commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The Bananapi M3 has an onboard IR receiver.
This enables the onboard IR receiver subnode.
Unlike the other IR receivers this one needs a base clock frequency
of 3000000 Hz (3 MHz), to be able to work.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The OPPs for the A83T CPU cores were added in v4.17 in commit 2db639d8c166
("ARM: dts: sun8i: a83t: add stable OPP tables and CPUfreq"), but board
level regulator supplies for the CPU clusters were only added for the
TBS-A711 tablet. This means the other A83T boards do not benefit from
voltage scaling, or worse, if the implementation does not scale the
frequency when the voltage is fixed, no benefit at all.
Add board level CPU cluster power supplies to all the A83T development
boards, so they can have proper dynamic CPU voltage and frequency scaling.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard:
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
* tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus
ARM: dts: sun8i-h3: Add Mali node
ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards
ARM: dts: sun8i: h3: Enable HDMI output on H3 boards
ARM: dts: sunxi: h3/h5: Add HDMI pipeline
ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node
ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi
ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl
ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
ARM: dts: nanopi-neo-air: Add WiFi / eMMC
|
|
BananaPi M3 includes HDMI connector, so add support for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Bananapi M3 has two controllable LEDs, blue and green, that are tied
to the PMIC's two GPIO pins.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Cubietruck Plus has a Realtek RTL8211E RGMII PHY tied to the EMAC.
The AXP818 PMIC's regulators provide main power and secondary signaling
voltages to the PHY. The latter is always on, as it also supplies the
pingroup on the SoC, which has other uses.
The Bananapi M3 has a Realtek RTL8211E RGMII PHY tied to the EMAC.
The AXP818 PMIC's SW regulators provides power to the PHY.
This patch enables Ethernet with the EMAC on both these boards by
enabling the emac node and setting all the required properties.
A proper ethernet alias is added as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The WiFi side of the AP6212 WiFi/BT combo module is connected to
mmc1. There are also GPIOs for enable and interrupts. An external
clock from the AC100 RTC is also used.
Enable WiFi on this board by enabling mmc1 and adding the power
sequencing clocks and GPIO, as well as the chip's interrupt line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch adds device nodes for all the regulators of the AXP813 PMIC.
Sunxi common regulators are removed, and USB VBUS regulators are added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The BPI-M3 is an Allwinner A83T based SBC in the Bananapi/Bpi family.
It is roughly the same form factor as the BPI-M1+, with roughly the
same peripherals and connectors:
- 2GB LPDDR3 DRAM
- 8GB eMMC
- Micro-SD card slot
- HDMI output
- Headset (stereo + mic) jack
- Onboard mic
- Gigabit Ethernet with RTL8211E transceiver
- Ampak AP6212 WiFi + BT
- USB OTG connector
- USB-to-SATA bridge connected through a USB 2.0 hub
- Consumer IR receiver
- MIPI DSI LCD panel connector
- Camera interface (parallel and MIPI CSI) connector
- 3 LEDs (Red, Green, Blue), of which 2 are controllable (GB)
- Raspberry Pi 2 compatible GPIO header
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
