From 421a6ba683f97713dc4f0e445aee48b87bbe18c8 Mon Sep 17 00:00:00 2001 From: Philippe Schenker Date: Mon, 27 Dec 2021 18:02:26 +0100 Subject: board: colibri-imx6ull: fix detecting ethernet phy now that it is possible to use regulator-fixed-clock make use of it. This makes U-Boot detect the PHY on first cold-boot. This commit also adjusts the code in setup_fec and follows how it is done in mx6ullevk.c This commit also slows down the boot-process by about 150ms as it now waits for the regulator-fixed-clock voltage that drives the PHY to go up. If you rely on very fast boot-speeds and don't need ethernet for your boot-process you can safely revert the changes on imx6ull-colibri.dtsi Signed-off-by: Philippe Schenker --- arch/arm/dts/imx6ull-colibri.dtsi | 13 +++++++++++++ board/toradex/colibri-imx6ull/colibri-imx6ull.c | 26 ++++++++++--------------- 2 files changed, 23 insertions(+), 16 deletions(-) diff --git a/arch/arm/dts/imx6ull-colibri.dtsi b/arch/arm/dts/imx6ull-colibri.dtsi index 56ee2895ae..88d5e15b8c 100644 --- a/arch/arm/dts/imx6ull-colibri.dtsi +++ b/arch/arm/dts/imx6ull-colibri.dtsi @@ -64,6 +64,18 @@ gpio = <&gpio1 2 GPIO_ACTIVE_LOW>; /* USBH_PEN */ vin-supply = <®_5v0>; }; + + reg_eth_phy: regulator-eth-phy { + compatible = "regulator-fixed-clock"; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "eth_phy"; + regulator-type = "voltage"; + vin-supply = <®_module_3v3>; + clocks = <&clks IMX6UL_CLK_ENET2_REF_125M>; + startup-delay-us = <150000>; + }; }; &adc1 { @@ -84,6 +96,7 @@ pinctrl-0 = <&pinctrl_enet2>; phy-mode = "rmii"; phy-handle = <ðphy1>; + phy-supply = <®_eth_phy>; status = "okay"; mdio { diff --git a/board/toradex/colibri-imx6ull/colibri-imx6ull.c b/board/toradex/colibri-imx6ull/colibri-imx6ull.c index 0ac86549fd..bc11ab2272 100644 --- a/board/toradex/colibri-imx6ull/colibri-imx6ull.c +++ b/board/toradex/colibri-imx6ull/colibri-imx6ull.c @@ -99,29 +99,23 @@ static int setup_fec(void) struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; int ret; - /* provide the PHY clock from the i.MX 6 */ + /* + * Use 50MHz anatop loopback REF_CLK2 for ENET2, + * clear gpr1[14], set gpr1[18]. + */ + clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK, + IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK); + + ret = enable_fec_anatop_clock(1, ENET_50MHZ); if (ret) return ret; - /* Use 50M anatop REF_CLK and output it on ENET2_TX_CLK */ - clrsetbits_le32(&iomuxc_regs->gpr[1], - IOMUX_GPR1_FEC2_CLOCK_MUX2_SEL_MASK, - IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK); - - /* give new Ethernet PHY power save mode circuitry time to settle */ - mdelay(300); - - return 0; -} + enable_enet_clk(1); -int board_phy_config(struct phy_device *phydev) -{ - if (phydev->drv->config) - phydev->drv->config(phydev); return 0; } -#endif /* CONFIG_FEC_MXC */ +#endif int board_init(void) { -- cgit v1.2.3