commit 2e18f5a1bc18e8af7031b3b26efde25307014837 upstream.

Introduce a dt property, ti,no-idle, that prevents an IP to idle at any
point. This is to handle Errata i877, which tells that GMAC clocks
cannot be disabled.

Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ARM DT updates from Olof Johansson:
 "As usual, this is the massive branch we have for each release.  Lots
  of various updates and additions of hardware descriptions on existing
  hardware, as well as the usual additions of new boards and SoCs.

  This is also the first release where we've started mixing 64- and
  32-bit DT updates in one branch.

  (Specific details on what's actually here and new is pretty easy to
  tell from the diffstat, so there's little point in duplicating listing
  it here)"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
  ARM: dts: uniphier: add system-bus-controller nodes
  ARM64: juno: disable NOR flash node by default
  ARM: dts: uniphier: add outer cache controller nodes
  arm64: defconfig: Enable PCI generic host bridge by default
  arm64: Juno: Add support for the PCIe host bridge on Juno R1
  Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
  ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
  dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
  dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
  dts/ls2080a: Update Simulator DTS to add support of various peripherals
  dts/ls2080a: Remove text about writing to Free Software Foundation
  dts/ls2080a: Update DTSI to add support of various peripherals
  doc: DTS: Update DWC3 binding to provide reference to generic bindings
  doc/bindings: Update GPIO devicetree binding documentation for LS2080A
  Documentation/dts: Move FSL board-specific bindings out of /powerpc
  Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
  arm64: Rename FSL LS2085A SoC support code to LS2080A
  arm64: Use generic Layerscape SoC family naming
  ARM: dts: uniphier: add ProXstream2 Vodka board support
  ARM: dts: uniphier: add ProXstream2 Gentil board support
  ...

Pull ARM SoC driver updates from Olof Johansson:
 "As we've enabled multiplatform kernels on ARM, and greatly done away
  with the contents under arch/arm/mach-*, there's still need for
  SoC-related drivers to go somewhere.

  Many of them go in through other driver trees, but we still have
  drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
  that might be shared between ARM and ARM64 (or just in general makes
  sense to not have under the architecture directory).

  This branch contains mostly such code:

   - Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
     communicate with power management blocks on these SoCs for use by
     clock, regulator and bus frequency drivers.

   - Allwinner Reduced Serial Bus driver, again used to communicate with
     PMICs.

   - Drivers for ARM's SCPI (System Control Processor).  Not to be
     confused with PSCI (Power State Coordination Interface).  SCPI is
     used to communicate with the assistant embedded cores doing power
     management, and we have yet to see how many of them will implement
     this for their hardware vs abstracting in other ways (or not at all
     like in the past).

   - To make confusion between SCPI and PSCI more likely, this release
     also includes an update of PSCI to interface version 1.0.

   - Rockchip support for power domains.

   - A driver to talk to the firmware on Raspberry Pi"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
  soc: qcom: smd-rpm: Correct size of outgoing message
  bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
  bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
  ARM: bcm2835: add mutual inclusion protection
  drivers: psci: make PSCI 1.0 functions initialization version dependent
  dt-bindings: Correct paths in Rockchip power domains binding document
  soc: rockchip: power-domain: don't try to print the clock name in error case
  soc: qcom/smem: add HWSPINLOCK dependency
  clk: berlin: add cpuclk
  ARM: berlin: dts: add CLKID_CPU for BG2Q
  ARM: bcm2835: Add the Raspberry Pi firmware driver
  soc: qcom: smem: Move RPM message ram out of smem DT node
  soc: qcom: smd-rpm: Correct the active vs sleep state flagging
  soc: qcom: smd: delete unneeded of_node_put
  firmware: qcom-scm: build for correct architecture level
  soc: qcom: smd: Correct SMEM items for upper channels
  qcom-scm: add missing prototype for qcom_scm_is_available()
  qcom-scm: fix endianess issue in __qcom_scm_is_call_available
  soc: qcom: smd: Reject send of too big packets
  soc: qcom: smd: Handle big endian CPUs
  ...

Pull ARM SoC platform updates from Olof Johansson:
 "New and/or improved SoC support for this release:

  Marvell Berlin:
     - Enable standard DT-based cpufreq
     - Add CPU hotplug support

  Freescale:
     - Ethernet init for i.MX7D
     - Suspend/resume support for i.MX6UL

  Allwinner:
     - Support for R8 chipset (used on NTC's $9 C.H.I.P board)

  Mediatek:
     - SMP support for some platforms

  Uniphier:
     - L2 support
     - Cleaned up SMP support, etc.

  plus a handful of other patches around above functionality, and a few
  other smaller changes"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
  ARM: uniphier: rework SMP operations to use trampoline code
  ARM: uniphier: add outer cache support
  Documentation: EXYNOS: Update bootloader interface on exynos542x
  ARM: mvebu: add broken-idle option
  ARM: orion5x: use mac_pton() helper
  ARM: at91: pm: at91_pm_suspend_in_sram() must be 8-byte aligned
  ARM: sunxi: Add R8 support
  ARM: digicolor: select pinctrl/gpio driver
  arm: berlin: add CPU hotplug support
  arm: berlin: use non-self-cleared reset register to reset cpu
  ARM: mediatek: add smp bringup code
  ARM: mediatek: enable gpt6 on boot up to make arch timer working
  soc: mediatek: Fix random hang up issue while kernel init
  soc: ti: qmss: make acc queue support optional in the driver
  soc: ti: add firmware file name as part of the driver
  Documentation: dt: soc: Add description for knav qmss driver
  ARM: S3C64XX: Use PWM lookup table for mach-smartq
  ARM: S3C64XX: Use PWM lookup table for mach-hmt
  ARM: S3C64XX: Use PWM lookup table for mach-crag6410
  ARM: S3C64XX: Use PWM lookup table for smdk6410
  ...

Pull ARM SoC cleanups from Olof Johansson:
 "Again we have a sizable (but not huge) cleanup branch with a net delta
  of about -3k lines.

  Main contents here is:

   - A bunch of development/cleanup of a few PXA boards
   - Removal of bockw platforms on shmobile, since the platform has now
     gone completely multiplatform.  Whee!
   - move of the 32kHz timer on OMAP to a proper timesource
   - Misc cleanup of older OMAP material (incl removal of one board
     file)
   - Switch over to new common PWM lookup support for several platforms

  There's also a handful of other cleanups across the tree, but the
  above are the major pieces"

* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits)
  ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
  ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
  ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
  ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
  ARM: Remove __ref on hotplug cpu die path
  ARM: Remove open-coded version of IRQCHIP_DECLARE
  arm: omap2: board-generic: use omap4_local_timer_init for AM437x
  ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
  ARM: OMAP: Remove duplicated operand in OR operation
  clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
  ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
  ARM: pxa: raumfeld: make some variables static
  ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
  ARM: OMAP2+: Rename cpu_is macros to soc_is
  arm: omap2: timer: limit hwmod usage to non-DT boots
  arm: omap2+: select 32k clocksource driver
  clocksource: add TI 32.768 Hz counter driver
  arm: omap2: timer: rename omap_sync32k_timer_init()
  arm: omap2: timer: always call clocksource_of_init() when DT
  arm: omap2: timer: move realtime_counter_init() around
  ...

Pull DeviceTree updates from Rob Herring:
 "A fairly large (by DT standards) pull request this time with the
  majority being some overdue moving DT binding docs around to
  consolidate similar bindings.

   - DT binding doc consolidation moving similar bindings to common
     locations.  The majority of these are display related which were
     scattered in video/, fb/, drm/, gpu/, and panel/ directories.

   - Add new config option, CONFIG_OF_ALL_DTBS, to enable building all
     dtbs in the tree for most arches with dts files (except powerpc for
     now).

   - OF_IRQ=n fixes for user enabled CONFIG_OF.

   - of_node_put ref counting fixes from Julia Lawall.

   - Common DT binding for wakeup-source and deprecation of all similar
     bindings.

   - DT binding for PXA LCD controller.

   - Allow ignoring failed PCI resource translations in order to ignore
     64-bit addresses on non-LPAE 32-bit kernels.

   - Support setting the NUMA node from DT instead of only from parent
     device.

   - Couple of earlycon DT parsing fixes for address and options"

* tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
  MAINTAINERS: update DT binding doc locations
  devicetree: add Sigma Designs vendor prefix
  of: simplify arch_find_n_match_cpu_physical_id() function
  Documentation: arm: Fixed typo in socfpga fpga mgr example
  Documentation: devicetree: fix reference to legacy wakeup properties
  Documentation: devicetree: standardize/consolidate on "wakeup-source" property
  drivers: of: removing assignment of 0 to static variable
  xtensa: enable building of all dtbs
  mips: enable building of all dtbs
  metag: enable building of all dtbs
  metag: use common make variables for dtb builds
  h8300: enable building of all dtbs
  arm64: enable building of all dtbs
  arm: enable building of all dtbs
  arc: enable building of all dtbs
  arc: use common make variables for dtb builds
  of: add config option to enable building of all dtbs
  of/fdt: fix error checking for earlycon address
  of/overlay: add missing of_node_put
  of/platform: add missing of_node_put
  ...

Pull PCI updates from Bjorn Helgaas:
 "Resource management:
   - Add support for Enhanced Allocation devices (Sean O. Stalley)
   - Add Enhanced Allocation register entries (Sean O. Stalley)
   - Handle IORESOURCE_PCI_FIXED when sizing resources (David Daney)
   - Handle IORESOURCE_PCI_FIXED when assigning resources (David Daney)
   - Handle Enhanced Allocation capability for SR-IOV devices (David Daney)
   - Clear IORESOURCE_UNSET when reverting to firmware-assigned address (Bjorn Helgaas)
   - Make Enhanced Allocation bitmasks more obvious (Bjorn Helgaas)
   - Expand Enhanced Allocation BAR output (Bjorn Helgaas)
   - Add of_pci_check_probe_only to parse "linux,pci-probe-only" (Marc Zyngier)
   - Fix lookup of linux,pci-probe-only property (Marc Zyngier)
   - Add sparc mem64 resource parsing for root bus (Yinghai Lu)

  PCI device hotplug:
   - pciehp: Queue power work requests in dedicated function (Guenter Roeck)

  Driver binding:
   - Add builtin_pci_driver() to avoid registration boilerplate (Paul Gortmaker)

  Virtualization:
   - Set SR-IOV NumVFs to zero after enumeration (Alexander Duyck)
   - Remove redundant validation of SR-IOV offset/stride registers (Alexander Duyck)
   - Remove VFs in reverse order if virtfn_add() fails (Alexander Duyck)
   - Reorder pcibios_sriov_disable() (Alexander Duyck)
   - Wait 1 second between disabling VFs and clearing NumVFs (Alexander Duyck)
   - Fix sriov_enable() error path for pcibios_enable_sriov() failures (Alexander Duyck)
   - Enable SR-IOV ARI Capable Hierarchy before reading TotalVFs (Ben Shelton)
   - Don't try to restore VF BARs (Wei Yang)

  MSI:
   - Don't alloc pcibios-irq when MSI is enabled (Joerg Roedel)
   - Add msi_controller setup_irqs() method for special multivector setup (Lucas Stach)
   - Export all remapped MSIs to sysfs attributes (Romain Bezut)
   - Disable MSI on SiS 761 (Ondrej Zary)

  AER:
   - Clear error status registers during enumeration and restore (Taku Izumi)

  Generic host bridge driver:
   - Fix lookup of linux,pci-probe-only property (Marc Zyngier)
   - Allow multiple hosts with different map_bus() methods (David Daney)
   - Pass starting bus number to pci_scan_root_bus() (David Daney)
   - Fix address window calculation for non-zero starting bus (David Daney)

  Altera host bridge driver:
   - Add msi.h to ARM Kbuild (Ley Foon Tan)
   - Add Altera PCIe host controller driver (Ley Foon Tan)
   - Add Altera PCIe MSI driver (Ley Foon Tan)

  APM X-Gene host bridge driver:
   - Remove msi_controller assignment (Duc Dang)

  Broadcom iProc host bridge driver:
   - Fix header comment "Corporation" misspelling (Florian Fainelli)
   - Fix code comment to match code (Ray Jui)
   - Remove unused struct iproc_pcie.irqs[] (Ray Jui)
   - Call pci_fixup_irqs() for ARM64 as well as ARM (Ray Jui)
   - Fix PCIe reset logic (Ray Jui)
   - Improve link detection logic (Ray Jui)
   - Update PCIe device tree bindings (Ray Jui)
   - Add outbound mapping support (Ray Jui)

  Freescale i.MX6 host bridge driver:
   - Return real error code from imx6_add_pcie_port() (Fabio Estevam)
   - Add PCIE_PHY_RX_ASIC_OUT_VALID definition (Fabio Estevam)

  Freescale Layerscape host bridge driver:
   - Remove ls_pcie_establish_link() (Minghuan Lian)
   - Ignore PCIe controllers in Endpoint mode (Minghuan Lian)
   - Factor out SCFG related function (Minghuan Lian)
   - Update ls_add_pcie_port() (Minghuan Lian)
   - Remove unused fields from struct ls_pcie (Minghuan Lian)
   - Add support for LS1043a and LS2080a (Minghuan Lian)
   - Add ls_pcie_msi_host_init() (Minghuan Lian)

  HiSilicon host bridge driver:
   - Add HiSilicon SoC Hip05 PCIe driver (Zhou Wang)

  Marvell MVEBU host bridge driver:
   - Return zero for reserved or unimplemented config space (Russell King)
   - Use exact config access size; don't read/modify/write (Russell King)
   - Use of_get_available_child_count() (Russell King)
   - Use for_each_available_child_of_node() to walk child nodes (Russell King)
   - Report full node name when reporting a DT error (Russell King)
   - Use port->name rather than "PCIe%d.%d" (Russell King)
   - Move port parsing and resource claiming to  separate function (Russell King)
   - Fix memory leaks and refcount leaks (Russell King)
   - Split port parsing and resource claiming from  port setup (Russell King)
   - Use gpio_set_value_cansleep() (Russell King)
   - Use devm_kcalloc() to allocate an array (Russell King)
   - Use gpio_desc to carry around gpio (Russell King)
   - Improve clock/reset handling (Russell King)
   - Add PCI Express root complex capability block (Russell King)
   - Remove code restricting accesses to slot 0 (Russell King)

  NVIDIA Tegra host bridge driver:
   - Wrap static pgprot_t initializer with __pgprot() (Ard Biesheuvel)

  Renesas R-Car host bridge driver:
   - Build pci-rcar-gen2.c only on ARM (Geert Uytterhoeven)
   - Build pcie-rcar.c only on ARM (Geert Uytterhoeven)
   - Make PCI aware of the I/O resources (Phil Edworthy)
   - Remove dependency on ARM-specific struct hw_pci (Phil Edworthy)
   - Set root bus nr to that provided in DT (Phil Edworthy)
   - Fix I/O offset for multiple host bridges (Phil Edworthy)

  ST Microelectronics SPEAr13xx host bridge driver:
   - Fix dw_pcie_cfg_read/write() usage (Gabriele Paoloni)

  Synopsys DesignWare host bridge driver:
   - Make "clocks" and "clock-names" optional DT properties (Bhupesh Sharma)
   - Use exact access size in dw_pcie_cfg_read() (Gabriele Paoloni)
   - Simplify dw_pcie_cfg_read/write() interfaces (Gabriele Paoloni)
   - Require config accesses to be naturally aligned (Gabriele Paoloni)
   - Make "num-lanes" an optional DT property (Gabriele Paoloni)
   - Move calculation of bus addresses to DRA7xx (Gabriele Paoloni)
   - Replace ARM pci_sys_data->align_resource with global function pointer (Gabriele Paoloni)
   - Factor out MSI msg setup (Lucas Stach)
   - Implement multivector MSI IRQ setup (Lucas Stach)
   - Make get_msi_addr() return phys_addr_t, not u32 (Lucas Stach)
   - Set up high part of MSI target address (Lucas Stach)
   - Fix PORT_LOGIC_LINK_WIDTH_MASK (Zhou Wang)
   - Revert "PCI: designware: Program ATU with untranslated address" (Zhou Wang)
   - Use of_pci_get_host_bridge_resources() to parse DT (Zhou Wang)
   - Make driver arch-agnostic (Zhou Wang)

  Miscellaneous:
   - Make x86 pci_subsys_init() static (Alexander Kuleshov)
   - Turn off Request Attributes to avoid Chelsio T5 Completion erratum (Hariprasad Shenai)"

* tag 'pci-v4.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (94 commits)
  PCI: altera: Add Altera PCIe MSI driver
  PCI: hisi: Add HiSilicon SoC Hip05 PCIe driver
  PCI: layerscape: Add ls_pcie_msi_host_init()
  PCI: layerscape: Add support for LS1043a and LS2080a
  PCI: layerscape: Remove unused fields from struct ls_pcie
  PCI: layerscape: Update ls_add_pcie_port()
  PCI: layerscape: Factor out SCFG related function
  PCI: layerscape: Ignore PCIe controllers in Endpoint mode
  PCI: layerscape: Remove ls_pcie_establish_link()
  PCI: designware: Make "clocks" and "clock-names" optional DT properties
  PCI: designware: Make driver arch-agnostic
  ARM/PCI: Replace pci_sys_data->align_resource with global function pointer
  PCI: designware: Use of_pci_get_host_bridge_resources() to parse DT
  Revert "PCI: designware: Program ATU with untranslated address"
  PCI: designware: Move calculation of bus addresses to DRA7xx
  PCI: designware: Make "num-lanes" an optional DT property
  PCI: designware: Require config accesses to be naturally aligned
  PCI: designware: Simplify dw_pcie_cfg_read/write() interfaces
  PCI: designware: Use exact access size in dw_pcie_cfg_read()
  PCI: spear: Fix dw_pcie_cfg_read/write() usage
  ...

Pull clk updates from Stephen Boyd:
 "The majority of the changes are driver updates and new device support.
  The core framework is mostly unchanged this time around, with only a
  couple patches to expose a clk provider API and make getting clk
  parent names from DT more robust.

  Driver updates:

   - Support for clock controllers found on Broadcom Northstar SoCs and
     bcm2835 SoC

   - Support for Allwinner audio clocks

   - A few cleanup patches for Tegra drivers and support for the highest
     DFLL frequencies on Tegra124

   - Samsung exynos7 fixes and improvements

   - i.Mx SoC updates to add a few missing clocks and keep debug uart
     clocks on during kernel intialization

   - Some mediatek cleanups and support for more subsystem clocks

   - Support for msm8916 gpu/audio clocks and qcom's GDSC power domain
     controllers

   - A new driver for the Silabs si514 clock chip"

* tag 'clk-for-linus-20151104' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (143 commits)
  clk: qcom: msm8960: Fix dsi1/2 halt bits
  clk: lpc18xx-cgu: fix potential system hang when disabling unused clocks
  clk: lpc18xx-ccu: fix potential system hang when disabling unused clocks
  clk: Add clk_hw_is_enabled() for use by clk providers
  clk: Add stubs for of_clk_*() APIs when CONFIG_OF=n
  clk: versatile-icst: fix memory leak
  clk: Remove clk_{register,unregister}_multiplier()
  clk: iproc: define Broadcom NS2 iProc clock binding
  clk: iproc: define Broadcom NSP iProc clock binding
  clk: ns2: add clock support for Broadcom Northstar 2 SoC
  clk: iproc: Separate status and control variables
  clk: iproc: Split off dig_filter
  clk: iproc: Add PLL base write function
  clk: nsp: add clock support for Broadcom Northstar Plus SoC
  clk: iproc: Add PWRCTRL support
  clk: cygnus: Convert all macros to all caps
  ARM: cygnus: fix link failures when CONFIG_COMMON_CLK_IPROC is disabled
  clk: imx31: add missing of_node_put
  clk: imx27: add missing of_node_put
  clk: si5351: add missing of_node_put
  ...

Pull arm64 updates from Catalin Marinas:

 - "genirq: Introduce generic irq migration for cpu hotunplugged" patch
   merged from tip/irq/for-arm to allow the arm64-specific part to be
   upstreamed via the arm64 tree

 - CPU feature detection reworked to cope with heterogeneous systems
   where CPUs may not have exactly the same features.  The features
   reported by the kernel via internal data structures or ELF_HWCAP are
   delayed until all the CPUs are up (and before user space starts)

 - Support for 16KB pages, with the additional bonus of a 36-bit VA
   space, though the latter only depending on EXPERT

 - Implement native {relaxed, acquire, release} atomics for arm64

 - New ASID allocation algorithm which avoids IPI on roll-over, together
   with TLB invalidation optimisations (using local vs global where
   feasible)

 - KASan support for arm64

 - EFI_STUB clean-up and isolation for the kernel proper (required by
   KASan)

 - copy_{to,from,in}_user optimisations (sharing the memcpy template)

 - perf: moving arm64 to the arm32/64 shared PMU framework

 - L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware

 - Support for the contiguous PTE hint on kernel mapping (16 consecutive
   entries may be able to use a single TLB entry)

 - Generic CONFIG_HZ now used on arm64

 - defconfig updates

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (91 commits)
  arm64/efi: fix libstub build under CONFIG_MODVERSIONS
  ARM64: Enable multi-core scheduler support by default
  arm64/efi: move arm64 specific stub C code to libstub
  arm64: page-align sections for DEBUG_RODATA
  arm64: Fix build with CONFIG_ZONE_DMA=n
  arm64: Fix compat register mappings
  arm64: Increase the max granular size
  arm64: remove bogus TASK_SIZE_64 check
  arm64: make Timer Interrupt Frequency selectable
  arm64/mm: use PAGE_ALIGNED instead of IS_ALIGNED
  arm64: cachetype: fix definitions of ICACHEF_* flags
  arm64: cpufeature: declare enable_cpu_capabilities as static
  genirq: Make the cpuhotplug migration code less noisy
  arm64: Constify hwcap name string arrays
  arm64/kvm: Make use of the system wide safe values
  arm64/debug: Make use of the system wide safe value
  arm64: Move FP/ASIMD hwcap handling to common code
  arm64/HWCAP: Use system wide safe values
  arm64/capabilities: Make use of system wide safe value
  arm64: Delay cpu feature capability checks
  ...

Pull irq updates from Thomas Gleixner:
 "The irq departement delivers:

   - Rework the irqdomain core infrastructure to accomodate ACPI based
     systems.  This is required to support ARM64 without creating
     artificial device tree nodes.

   - Sanitize the ACPI based ARM GIC initialization by making use of the
     new firmware independent irqdomain core

   - Further improvements to the generic MSI management

   - Generalize the irq migration on CPU hotplug

   - Improvements to the threaded interrupt infrastructure

   - Allow the migration of "chained" low level interrupt handlers

   - Allow optional force masking of interrupts in disable_irq[_nosysnc]

   - Support for two new interrupt chips - Sigh!

   - A larger set of errata fixes for ARM gicv3

   - The usual pile of fixes, updates, improvements and cleanups all
     over the place"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
  Document that IRQ_NONE should be returned when IRQ not actually handled
  PCI/MSI: Allow the MSI domain to be device-specific
  PCI: Add per-device MSI domain hook
  of/irq: Use the msi-map property to provide device-specific MSI domain
  of/irq: Split of_msi_map_rid to reuse msi-map lookup
  irqchip/gic-v3-its: Parse new version of msi-parent property
  PCI/MSI: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
  of/irq: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
  of/irq: Add support code for multi-parent version of "msi-parent"
  irqchip/gic-v3-its: Add handling of PCI requester id.
  PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().
  of/irq: Add new function of_msi_map_rid()
  Docs: dt: Add PCI MSI map bindings
  irqchip/gic-v2m: Add support for multiple MSI frames
  irqchip/gic-v3: Fix translation of LPIs after conversion to irq_fwspec
  irqchip/mxs: Add Alphascale ASM9260 support
  irqchip/mxs: Prepare driver for hardware with different offsets
  irqchip/mxs: Panic if ioremap or domain creation fails
  irqdomain: Documentation updates
  irqdomain/msi: Use fwnode instead of of_node
  ...