This patch adds support to configure the STMMAC ethernet driver via
device-tree instead of platform_data.

Currently, only the properties needed on SPEAr600 are provided. All
other properties should be added once needed on other platforms.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver specific changes

Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
  ARM: sa1100: clean up of the clock support
  ARM: pxa: add dummy clock for sa1100-rtc
  RTC: sa1100: support sa1100, pxa and mmp soc families
  RTC: sa1100: remove redundant code of setting alarm
  RTC: sa1100: Clean out ost register
  Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
  pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
  ARM: EXYNOS: Modified files for SPI consolidation work
  ARM: S5P64X0: Enable SDHCI support
  ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
  ARM: S5P64X0: Add HSMMC setup for host Controller
  ARM: EXYNOS: Add USB OHCI support to ORIGEN board
  USB: Add Samsung Exynos OHCI diver
  ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
  ARM: EXYNOS: Add USB OHCI device
  net: macb: fix build break with !CONFIG_OF
  i2c: tegra: Support DVC controller in device tree
  i2c: tegra: Add __devinit/exit to probe/remove
  net/at91_ether: use gpio_is_valid for phy IRQ line
  ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
  ...

Allow the device tree to provide the mac address and the phy mode.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change "compatible" node property, doc and DT hwaddr]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[jamie@jamieiles.com: add "gem" compatibility strings and doc]
Acked-by: Jamie Iles<jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>

This driver works with both, static platform data and device tree
bindings. It has been tested on a TQM855L board with two AN82527
CAN controllers on the local bus.

CC: Devicetree-discuss@lists.ozlabs.org
CC: linuxppc-dev@ozlabs.org
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the XGMAC 10Gb ethernet device in the Calxeda Highbank
SOC.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If our CAN device's device tree node has a clock-frequency property,
then use that value for the can devices clock frequency.  If not, fall
back to asking the platform/mach code for the clock frequency associated
with the flexcan device.

Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleans up the documentation of the device-tree binding for
the Flexcan devices on Freescale's PowerPC and ARM cores. Extra
properties are not used by the driver so we are removing them.

Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>,
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>

It adds device tree probe support for smsc911x driver.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

For testing the dt work, define a dt-enabled versatile platform.

This patch adds a new versatile platform for when using the device
tree.  Add platform and amba devices are discovered and registered by
parsing the device tree.  Clocks and initial io mappings are still
configured statically.

This patch still depends on some static platform_data for a few devices
which is passed via the auxdata structure to of_platform_populate(),
but it is a viable starting point until the drivers can get all
configuration data out of the device tree.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>