RGMII requires special RX and/or TX delays depending on the actual
hardware circuit/wiring. These delays can be added by the MAC, the PHY
or the designer of the circuit (the latter means that no delay has to
be added by PHY or MAC).
There are 4 RGMII phy-modes used describe where a delay should be
applied:
- rgmii: the RX and TX delays are either added by the MAC (where the
  exact delay is typically configurable, and can be turned off when no
  extra delay is needed) or not needed at all (because the hardware
  wiring adds the delay already). The PHY should neither add the RX nor
  TX delay in this case.
- rgmii-rxid: configures the PHY to enable the RX delay. The MAC should
  not add the RX delay in this case.
- rgmii-txid: configures the PHY to enable the TX delay. The MAC should
  not add the TX delay in this case.
- rgmii-id: combines rgmii-rxid and rgmii-txid and thus configures the
  PHY to enable the RX and TX delays. The MAC should neither add the RX
  nor TX delay in this case.

Document these cases in the ethernet.txt documentation to make it clear
when to use each mode.
If applied incorrectly one might end up with MAC and PHY both enabling
for example the TX delay, which breaks ethernet TX traffic on 1000Mbit/s
links.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MAC is capable of RGMII mode and that is probably a more typical
connection type than GMII today (eg it is used by Marvell Reference
designs for several SOCs). Let DT users specify the standard

   phy-connection-type = "rgmii-id";

On a phy node.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Netfilter list handling fix, from Linus.

 2) RXRPC/AFS bug fixes from David Howells (oops on call to serviceless
    endpoints, build warnings, missing notifications, etc.) From David
    Howells.

 3) Kernel log message missing newlines, from Colin Ian King.

 4) Don't enter direct reclaim in netlink dumps, the idea is to use a
    high order allocation first and fallback quickly to a 0-order
    allocation if such a high-order one cannot be done cheaply and
    without reclaim. From Eric Dumazet.

 5) Fix firmware download errors in btusb bluetooth driver, from Ethan
    Hsieh.

 6) Missing Kconfig deps for QCOM_EMAC, from Geert Uytterhoeven.

 7) Fix MDIO_XGENE dup Kconfig entry. From Laura Abbott.

 8) Constrain ipv6 rtr_solicits sysctl values properly, from Maciej
    Żenczykowski.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
  netfilter: Fix slab corruption.
  be2net: Enable VF link state setting for BE3
  be2net: Fix TX stats for TSO packets
  be2net: Update Copyright string in be_hw.h
  be2net: NCSI FW section should be properly updated with ethtool for BE3
  be2net: Provide an alternate way to read pf_num for BEx chips
  wan/fsl_ucc_hdlc: Fix size used in dma_free_coherent()
  net: macb: NULL out phydev after removing mdio bus
  xen-netback: make sure that hashes are not send to unaware frontends
  Fixing a bug in team driver due to incorrect 'unsigned int' to 'int' conversion
  MAINTAINERS: add myself as a maintainer of xen-netback
  ipv6 addrconf: disallow rtr_solicits < -1
  Bluetooth: btusb: Fix atheros firmware download error
  drivers: net: phy: Correct duplicate MDIO_XGENE entry
  ethernet: qualcomm: QCOM_EMAC should depend on HAS_DMA and HAS_IOMEM
  net: ethernet: mediatek: remove hwlro property in the device tree
  net: ethernet: mediatek: get hw lro capability by the chip id instead of by the dtsi
  net: ethernet: mediatek: get the chip id by ETHDMASYS registers
  net: bgmac: Fix errant feature flag check
  netlink: do not enter direct reclaim from netlink_dump()
  ...

Pull ARM SoC late DT updates from Arnd Bergmann:
 "These updates have been kept in a separate branch mostly because they
  rely on updates to the respective clk drivers to keep the shared
  header files in sync.

   - The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
     automotive SoC similar to the ⅹ8a7795 chip we already support, but
     the dts changes rely on a clock driver change that has been merged
     for v4.9 through the clk tree.

   - The Amlogic meson-gxbb (S905) platform gains support for a few
     drivers merged through our tree, in particular the network and usb
     driver changes are required and included here, and also the clk
     tree changes.

   - The Allwinner platforms have seen a large-scale change to their clk
     drivers and the dts file updates must come after that. This
     includes the newly added Nextthing GR8 platform, which is derived
     from sun5i/A13.

   - Some integrator (arm32) changes rely on clk driver changes.

   - A single patch for lpc32xx has no such dependency but wasn't added
     until just before the merge window"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
  ARM: dts: lpc32xx: add device node for IRAM on-chip memory
  ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
  ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
  ARM: dts: sun8i: add pinmux for UART1 at PG
  dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
  dts: sun8i-h3: add pinmux definitions for I2C0-2
  dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
  dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
  dts: sun8i-h3: add pinmux definitions for UART2-3
  ARM: dts: sun9i: a80-optimus: Disable EHCI1
  ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
  ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
  ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
  ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
  ...

Pull ARM DT updates from Arnd Bergmann:
 "These are as usual a very large number of mostly boring updates to
  enable devices in existing machines, or to fix minor bugs. Notably, an
  ongoing treewide effort to fix warnings caused by an update to the
  device tree compiler. These are enabled with "make W=1" at the moment
  but can hopefully become the default once all issues have been
  addressed.

  No new SoC platform is added this time around (Armada 395 and Orion
  mv88f5181 are slight variations of existing ones), but a significant
  number of new dts files are added, which I list by platform:

   - Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets,
     Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange Pi Lite,
     Olimex A33-Olinuxino, and Nano Pi Neo single-board computers

   - ARM Realview: all supported machines (ported from board files)

   - Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
     BCM958622hr reference boards for Northstar platform, Raspberry Pi
     Zero single-board computer

   - Marvell EBU: Netgear WNR854T router (ported from board file),
     Armada 395 SoC platform and GP board Armada 390 DB development
     board

   - NXP i.MX: imx7s Warp7 reference board, Gateworks Ventana GW553x
     single-board computer, Technologic Systems TS-4900 and Engicam
     IMX6UL GEA M6UL computer-on-module, Inverse Path USB armory board

   - Qualcomm: LG Nexus 5 Phone

   - Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards

   - Rockchip: Rockchip RK3288 Fennec reference board, Firefly RK3288
     Reload platform

   - ST Microelectronics STi: B2260 (96boards) single-board computer

   - TI Davinci: OMAP-L138 LCDK Development kit

   - TI OMAP: beagleboard-x15 rev B1 single-board computer"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (390 commits)
  ARM: dts: sony-nsz-gs7: add missing unit name to /memory node
  ARM: dts: chromecast: add missing unit name to /memory node
  ARM: dts: berlin2q-marvell-dmp: add missing unit name to /memory node
  ARM: dts: berlin2: Add missing unit name to /soc node
  ARM: dts: berlin2cd: Add missing unit name to /soc node
  ARM: dts: berlin2q: Add missing unit name to /soc node
  ARM: dts: berlin2: Remove skeleton.dtsi inclusion
  ARM: dts: berlin2cd: Remove skeleton.dtsi inclusion
  ARM: dts: berlin2q: Remove skeleton.dtsi inclusion
  arm: dts: berlin2q: enable all wdt nodes unconditionally
  arm: dts: berlin2: enable all wdt nodes unconditionally
  ARM: dts: omap5-igep0050.dts: Use tabs for indentation
  ARM: dts: Fix igepv5 power button GPIO direction
  ARM: dts: am335x-evmsk: Add blue-and-red-wiring -property to lcdc node
  ARM: dts: am335x-evmsk: Whitespace cleanup of lcdc related nodes
  ARM: dts: am335x-evm: Add blue-and-red-wiring -property to lcdc node
  ARM: dts: s3c64xx: Use macros for pinctrl configuration
  ARM: dts: s3c2416: Use macros for pinctrl configuration
  ARM: dts: s5pv210: Use macros for pinctrl configuration
  ARM: dts: s3c64xx: Use common macros for pinctrl configuration
  ...

Since the proper way to check the hw lro capability is by the chip id,
hwlro property in the device tree should be removed.

Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The KSZ9031 skew registers contain an offset, the chip's default value
is "neutral" which does not add any skew. Programming a 0 into a skew
property will actually set it the maximal negative adjustment and not
to a neutral position as one would expect.

Explain this situation in the devicetree binding documentation and list
the settings that the chip considers neutral.

Changing the implementation to accept negative values would have been
a better solution, but would break existing configurations.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new compatible string for the R8A7796 (M3-W) RAVB.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull DeviceTree updates from Rob Herring:

 - update changeset documentation on locking to reflect current code

 - fix alphabetizing of vendor-prefixes.txt

 - add various vendor prefixes

 - add ESP8089 WiFi binding

 - add new variable sized array parsing functions

* tag 'devicetree-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (21 commits)
  DT: irqchip: renesas-irqc: document R8A7743/5 support
  dt-bindings: Add Keith&Koep vendor prefix
  dt-bindings: add vendor prefix for Auvidea GmbH
  of: Add vendor prefix for Engicam s.r.l company
  devicetree: Add vendor-prefix for Silead Inc.
  devicetree: bindings: Add vendor prefix for Topeet.
  dt-bindings: Add summit vendor id
  of/platform: Initialise dev->fwnode appropriately
  of: Add array read functions with min/max size limits
  of: Make of_find_property_value_of_size take a length range
  dt: net: enhance DWC EQoS binding to support Tegra186
  bindings: PCI: artpec: correct pci binding example
  Documentation: devicetree: Fix max77693 spelling errors
  dt: bindings: Add binding for ESP8089 wifi chips
  PCI: Xilinx NWL PCIe: Updating device tree documentation with prefetchable memory space
  Documentation: devicetree: spi: fix wrong spi-bus documentation
  dt-bindings: Add Japan Display Inc vendor id
  dt-bindings: vendor-prefixes: Add Sierra Wireless
  devicetree: Add vendor prefix for Shenzhen Sunchip Technology Co., Ltd
  devicetree: Sort vendor prefixes in alphabetical order
  ...

Edge-rate:
As system and networking speeds increase, a signal's output transition,
also know as the edge rate or slew rate (V/ns), takes on greater importance
because high-speed signals come with a price. That price is an assortment of
interference problems like ringing on the line, signal overshoot and
undershoot, extended signal settling times, crosstalk noise, transmission
line reflections, false signal detection by the receiving device and
electromagnetic interference (EMI) -- all of which can negate the potential
gains designers are seeking when they try to increase system speeds through
the use of higher performance logic devices. The fact is, faster signaling
edge rates can cause a higher level of electrical noise or other type of
interference that can actually lead to slower line speeds and lower maximum
system frequencies. This parameter allow the board designers to change the
driving strange, and thereby change the EMI behavioral.

Edge-rate parameters (vddmac, edge-slowdown) get from Device Tree.

Tested on Beaglebone Black with VSC 8531 PHY.

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>