Fix gpio number assignment, so that it can match the number stated in the comment.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Fix gpio number assignment, so that it can match the number stated in the comment.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Add missing 'reg' description.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
----
 .../devicetree/bindings/input/fsl-mma8450.txt      |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Fix gpio number assignment, so that it can match the number stated in the comment.

Cc:
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

The gpio numbers does not match the comment.

Fix the comments for GPIOs used for chip selects.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

This commit adds a device tree vendor prefix for Avionic Design GmbH.

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

This is useful for SoCs whose I2C module's signals can be routed to
different sets of pins at run-time, using the pinctrl API.

                                 +-----+  +-----+
                                 | dev |  | dev |
    +------------------------+   +-----+  +-----+
    | SoC                    |      |        |
    |                   /----|------+--------+
    |   +---+   +------+     | child bus A, on first set of pins
    |   |I2C|---|Pinmux|     |
    |   +---+   +------+     | child bus B, on second set of pins
    |                   \----|------+--------+--------+
    |                        |      |        |        |
    +------------------------+  +-----+  +-----+  +-----+
                                | dev |  | dev |  | dev |
                                +-----+  +-----+  +-----+

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Pull mtd update from David Woodhouse:
 - More robust parsing especially of xattr data in JFFS2
 - Updates to mxc_nand and gpmi drivers to support new boards and device tree
 - Improve consistency of information about ECC strength in NAND devices
 - Clean up partition handling of plat_nand
 - Support NAND drivers without dedicated access to OOB area
 - BCH hardware ECC support for OMAP
 - Other fixes and cleanups, and a few new device IDs

Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.

* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
  mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
  mtd: block2mtd: fix recursive call of mtd_writev
  mtd: gpmi-nand: define ecc.strength
  mtd: of_parts: fix breakage in Kconfig
  mtd: nand: fix scan_read_raw_oob
  mtd: docg3 fix in-middle of blocks reads
  mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
  mtd: add fixup for S29NS512P NOR flash.
  jffs2: allow to complete xattr integrity check on first GC scan
  jffs2: allow to discriminate between recoverable and non-recoverable errors
  mtd: nand: omap: add support for hardware BCH ecc
  ARM: OMAP3: gpmc: add BCH ecc api and modes
  mtd: nand: check the return code of 'read_oob/read_oob_raw'
  mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
  mtd: m25p80: Add support for Winbond W25Q80BW
  jffs2: get rid of jffs2_sync_super
  jffs2: remove unnecessary GC pass on sync
  jffs2: remove unnecessary GC pass on umount
  jffs2: remove lock_super
  mtd: gpmi: add gpmi support for mx6q
  ...

Pull IOMMU updates from Joerg Roedel:
 "Not much stuff this time.  The only change to the IOMMU core code is
  the addition of a handle to the fault handling code.  A few updates to
  the AMD IOMMU driver to work around new errata.  The other patches are
  mostly fixes and enhancements to the existing ARM IOMMU drivers and
  documentation updates.

  A new IOMMU driver for the Exynos platform was also underway but got
  merged via the Samsung tree and is not part of this tree."

* tag 'iommu-updates-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  Documentation: kernel-parameters.txt Add amd_iommu_dump
  iommu/core: pass a user-provided token to fault handlers
  iommu/tegra: gart: Fix register offset correctly
  iommu: OMAP: device detach on domain destroy
  iommu: tegra/gart: Add device tree support
  iommu: tegra/gart: use correct gart_device
  iommu/tegra: smmu: Print device name correctly
  iommu/amd: Add workaround for event log erratum
  iommu/amd: Check for the right TLP prefix bit
  dma-debug: release free_entries_lock before saving stack trace