Pull more power-supply updates from Sebastian Reichel:
 "The power-supply subsystem has a few more changes for the v4.12 merge
  window:

   - New battery driver for AXP20X and AXP22X PMICs

   - Improve max17042_battery for usage on x86

   - Misc small cleanups & fixes"

* tag 'for-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (34 commits)
  power: supply: cpcap-charger: Keep trickle charger bits disabled
  power: supply: cpcap-charger: Fix enable for 3.8V charge setting
  power: supply: cpcap-charger: Fix charge voltage configuration
  power: supply: cpcap-charger: Fix charger name
  power: supply: twl4030-charger: make twl4030_bci_property_is_writeable static
  power: supply: sbs-battery: Add alert callback
  mailmap: add Sebastian Reichel
  power: supply: avoid unused twl4030-madc.h
  power: supply: sbs-battery: Correct supply status with current draw
  power: supply: sbs-battery: Don't ignore the first external power change
  power: supply: pda_power: move from timer to delayed_work
  power: supply: max17042_battery: Add support for the SCOPE property
  power: supply: max17042_battery: Add support for the CHARGE_NOW property
  power: supply: max17042_battery: Add support for the CHARGE_FULL_DESIGN property
  power: supply: max17042_battery: mAh readings depend on r_sns value
  power: supply: max17042_battery: Add support for the VOLT_MIN property
  power: supply: max17042_battery: Add support for the TECHNOLOGY attribute
  power: supply: max17042_battery: Add external_power_changed callback
  power: supply: max17042_battery: Add support for the STATUS property
  power: supply: max17042_battery: Add default platform_data fallback data
  ...

Pull thermal management updates from Zhang Rui:

 - Fix a problem where orderly_shutdown() is called for multiple times
   due to multiple critical overheating events raised in a short period
   by platform thermal driver. (Keerthy)

 - Introduce a backup thermal shutdown mechanism, which invokes
   kernel_power_off()/emergency_restart() directly, after
   orderly_shutdown() being issued for certain amount of time(specified
   via Kconfig). This is useful in certain conditions that userspace may
   be unable to power off the system in a clean manner and leaves the
   system in a critical state, like in the middle of driver probing
   phase. (Keerthy)

 - Introduce a new interface in thermal devfreq_cooling code so that the
   driver can provide more precise data regarding actual power to the
   thermal governor every time the power budget is calculated. (Lukasz
   Luba)

 - Introduce BCM 2835 soc thermal driver and northstar thermal driver,
   within a new sub-folder. (Rafał Miłecki)

 - Introduce DA9062/61 thermal driver. (Steve Twiss)

 - Remove non-DT booting on TI-SoC driver. Also add support to fetching
   coefficients from DT. (Keerthy)

 - Refactorf RCAR Gen3 thermal driver. (Niklas Söderlund)

 - Small fix on MTK and intel-soc-dts thermal driver. (Dawei Chien,
   Brian Bian)

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
  thermal: core: Add a back up thermal shutdown mechanism
  thermal: core: Allow orderly_poweroff to be called only once
  Thermal: Intel SoC DTS: Change interrupt request behavior
  trace: thermal: add another parameter 'power' to the tracing function
  thermal: devfreq_cooling: add new interface for direct power read
  thermal: devfreq_cooling: refactor code and add get_voltage function
  thermal: mt8173: minor mtk_thermal.c cleanups
  thermal: bcm2835: move to the broadcom subdirectory
  thermal: broadcom: ns: specify myself as MODULE_AUTHOR
  thermal: da9062/61: Thermal junction temperature monitoring driver
  Documentation: devicetree: thermal: da9062/61 TJUNC temperature binding
  thermal: broadcom: add Northstar thermal driver
  dt-bindings: thermal: add support for Broadcom's Northstar thermal
  thermal: bcm2835: add thermal driver for bcm2835 SoC
  dt-bindings: Add thermal zone to bcm2835-thermal example
  thermal: rcar_gen3_thermal: add suspend and resume support
  thermal: rcar_gen3_thermal: store device match data in private structure
  thermal: rcar_gen3_thermal: enable hardware interrupts for trip points
  thermal: rcar_gen3_thermal: record and check number of TSCs found
  thermal: rcar_gen3_thermal: check that TSC exists before memory allocation
  ...

Pull more powerpc updates from Michael Ellerman:
 "The change to the Linux page table geometry was delayed for more
  testing with 16G pages, and there's the new CPU features stuff which
  just needed one more polish before going in. Plus a few changes from
  Scott which came in a bit late. And then various fixes, mostly minor.

  Summary highlights:

   - rework the Linux page table geometry to lower memory usage on
     64-bit Book3S (IBM chips) using the Hash MMU.

   - support for a new device tree binding for discovering CPU features
     on future firmwares.

   - Freescale updates from Scott:
      "Includes a fix for a powerpc/next mm regression on 64e, a fix for
       a kernel hang on 64e when using a debugger inside a relocated
       kernel, a qman fix, and misc qe improvements."

  Thanks to: Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong,
  Nicholas Piggin, Roy Pledge, Scott Wood, Valentin Longchamp"

* tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Support new device tree binding for discovering CPU features
  powerpc: Don't print cpu_spec->cpu_name if it's NULL
  of/fdt: introduce of_scan_flat_dt_subnodes and of_get_flat_dt_phandle
  powerpc/64s: Fix unnecessary machine check handler relocation branch
  powerpc/mm/book3s/64: Rework page table geometry for lower memory usage
  powerpc: Fix distclean with Makefile.postlink
  powerpc/64e: Don't place the stack beyond TASK_SIZE
  powerpc/powernv: Block PCI config access on BCM5718 during EEH recovery
  powerpc/8xx: Adding support of IRQ in MPC8xx GPIO
  soc/fsl/qbman: Disable IRQs for deferred QBMan work
  soc/fsl/qe: add EXPORT_SYMBOL for the 2 qe_tdm functions
  soc/fsl/qe: only apply QE_General4 workaround on affected SoCs
  soc/fsl/qe: round brg_freq to 1kHz granularity
  soc/fsl/qe: get rid of immrbar_virt_to_phys()
  net: ethernet: ucc_geth: fix MEM_PART_MURAM mode
  powerpc/64e: Fix hang when debugging programs with relocated kernel

Pull fbdev updates from Bartlomiej Zolnierkiewicz:
 "There is nothing really major here, just a couple of small bugfixes,
  improvements and cleanups.

   - fix handling of probing errors in omapfb (Arvind Yadav)

   - remove incorrect __exit markups in few drivers (Dmitry Torokhov)

   - fix boot time logo support for drivers using deferred probe
     (Takeshi Kihara)

   - fix DMA allocation size for ARM CLCD driver (Liam Beguin)

   - add support for specifying size via xenstore in xen-frontfb
     (Juergen Gross)

   - support for AUS mode in imxfb driver (Martin Kaiser)

   - fix buffer on stack usage in udlfb driver (Maksim Salau)

   - probe failure path fixup in sm501fb driver (Alexey Khoroshilov)

   - fix config dependency loop for stifb driver (Arnd Bergmann)

   - misc cleanups (Joe Perches, Christophe Leroy, Karim Eshapa, Pushkar
     Jambhlekar)"

* tag 'fbdev-v4.12' of git://github.com/bzolnier/linux:
  fbdev: sti: don't select CONFIG_VT
  drivers/video/fbdev/omap/lcd_mipid.c: Use time comparison kernel macros
  sm501fb: don't return zero on failure path in sm501fb_start()
  video: fbdev: udlfb: Fix buffer on stack
  video: console: Remove reference to CONFIG_8xx
  dt-bindings: display: imx: entry for AUS mode
  video: fbdev: imxfb: support AUS mode
  drivers/video/fbdev: Fixing coding guidelines in acornfb.c
  xen, fbfront: add support for specifying size via xenstore
  video: ARM CLCD: fix dma allocation size
  drivers/video: Convert remaining uses of pr_warning to pr_warn
  video/logo: tidyup fb_logo_late_init initcall timing
  video: fbdev: i810: remove incorrect __exit markups
  video: fbdev: pmag-aa-fb: remove incorrect __exit markups
  video: fbdev: pmagb-b-fb: remove incorrect __exit markups
  video: fbdev: pmag-ba-fb: remove incorrect __exit markups
  omapfb: dss: Handle return errors in dss_init_ports()

Pull MTD updates from Brian Norris:
 "NAND, from Boris:
   - some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
     davinci, brcmnand, omap)
   - a huge cleanup/rework of the denali driver accompanied with core
     fixes/improvements to simplify the driver code
   - a complete rewrite of the atmel driver to support new DT bindings
     make future evolution easier
   - the addition of per-vendor detection/initialization steps to avoid
     extending the nand_ids table with more extended-id entries

  SPI NOR, from Cyrille:
   - fixes in the hisi, intel and Mediatek SPI controller drivers
   - fixes to some SPI flash memories not supporting the Chip Erase
     command.
   - add support to some new memory parts (Winbond, Macronix, Micron,
     ESMT).
   - add new driver for the STM32 QSPI controller

  And a few fixes for Gemini and Versatile platforms on physmap-of"

* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
  MAINTAINERS: Update NAND subsystem git repositories
  mtd: nand: gpio: update binding
  mtd: nand: add ooblayout for old hamming layout
  mtd: oxnas_nand: Allocating more than necessary in probe()
  dt-bindings: mtd: Document the STM32 QSPI bindings
  mtd: mtk-nor: set controller's address width according to nor flash
  mtd: spi-nor: add driver for STM32 quad spi flash controller
  mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
  mtd: nand: davinci: add comment on NAND subpage write status on keystone
  mtd: nand: omap2: Fix partition creation via cmdline mtdparts
  mtd: nand: NULL terminate a of_device_id table
  mtd: nand: Fix a couple error codes
  mtd: nand: allow drivers to request minimum alignment for passed buffer
  mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
  mtd: nand: denali: allow to override revision number
  mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
  mtd: nand: denali_dt: remove dma-mask DT property
  mtd: nand: denali: support 64bit capable DMA engine
  mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
  mtd: nand: denali: support HW_ECC_FIXUP capability
  ...

Pull RTC updates from Alexandre Belloni:
 "RTC subsystem update:
   - Add OF device ID table for i2c drivers

  New RTC driver:
   - Motorola CPCAP PMIC RTC

  RTC driver updates:
   - cmos: fix IRQ selection
   - ds1307: Add ST m41t0 support
   - ds1374: fix watchdog configuration
   - sh: Add rza series support"

* tag 'rtc-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (33 commits)
  rtc: gemini: add return value validation
  rtc: snvs: fix an incorrect check of return value
  rtc: ds1374: wdt: Fix stop/start ioctl always returning -EINVAL
  rtc: ds1374: wdt: Fix issue with timeout scaling from secs to wdt ticks
  rtc: sh: mark PM functions as unused
  rtc: hid-sensor-time: remove some dead code
  rtc: m41t80: Add proper compatible for rv4162
  rtc: ds1307: Add m41t0 to OF device ID table
  rtc: ds1307: support m41t0 variant
  rtc: cpcap: fix improper use of IRQ_NONE for request_threaded_irq
  rtc: cmos: Do not assume irq 8 for rtc when there are no legacy irqs
  x86: i8259: export legacy_pic symbol
  dt-bindings: rtc: document the rtc-sh bindings
  rtc: sh: add support for rza series
  rtc: cpcap: kfreeing devm allocated memory
  rtc: wm8350: Remove unused to_wm8350_from_rtc_dev
  rtc: cpcap: new rtc driver
  dt-bindings: Add vendor prefix for Motorola
  rtc: omap: mark PM methods as __maybe_unused
  rtc: omap: remove incorrect __exit markups
  ...

This patch updates the binding documentation in accordance with
commit 44dd182861f99 ("mtd: nand: gpio: make nCE GPIO optional")

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Pull clk updates from Stephen Boyd:
 "Sort of on the quieter side this time, which is probably due more to
  me not catching up as quickly on patch review than anything else.
  Overall it seems normal though, a few small changes to the core,
  mostly small non-critical fixes here and there as well as driver
  updates for new and existing hardware support.

  The biggest things are the TI clk driver rework to lay the groundwork
  for clkctrl support in the next merge window and the AmLogic
  audio/graphics clk support.

  Core:
   - clk_possible_parents debugfs file so we know which parents a clk
     could possibly have
   - Fix to make clk rate change notifiers stop on the first failure
     instead of continuing

  New Drivers:
   - Mediatek MT6797 SoCs
   - hi655x PMIC clks
   - AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
   - Allwinner H5 SoCs and PRCM hardware

  Updates:
   - Nvidia Tegra T210 cleanups and non-critical fixes
   - TI OMAP cleanups in preparation for clkctrl support
   - trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
   - ZTE zx296718 SoC VGA clks
   - Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
   - IDT VersaClock 5P49V5935 support
   - Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3
     support"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (151 commits)
  clk: x86: pmc-atom: Checking for IS_ERR() instead of NULL
  clk: ti: divider: try to fix ti_clk_register_divider
  clk: mvebu: Use kcalloc() in two functions
  clk: mvebu: Use kcalloc() in of_cpu_clk_setup()
  clk: nomadik: Delete error messages for a failed memory allocation in two functions
  clk: nomadik: Use seq_puts() in nomadik_src_clk_show()
  clk: Improve a size determination in two functions
  clk: Replace four seq_printf() calls by seq_putc()
  clk: si5351: Delete an error message for a failed memory allocation in si5351_i2c_probe()
  clk: si5351: Use devm_kcalloc() in si5351_i2c_probe()
  clk: at91: Use kcalloc() in of_at91_clk_pll_get_characteristics()
  reset: mediatek: Add MT2701 ethsys reset controller include file
  clk: mediatek: add mt2701 ethernet reset
  clk: hi6220: Add the hi655x's pmic clock
  clk: ti: fix building without legacy omap3
  clk: ti: fix linker error with !SOC_OMAP4
  clk: hi3620: Fix a typo in one variable name
  clk: hi3620: Delete error messages for a failed memory allocation in two functions
  clk: hi3620: Use kcalloc() in hi3620_mmc_clk_init()
  clk: hisilicon: Delete error messages for failed memory allocations in hisi_clk_init()
  ...

Pull TEE driver infrastructure and OP-TEE drivers from Arnd Bergmann:
 "This introduces a generic TEE framework in the kernel, to handle
  trusted environemtns (security coprocessor or software implementations
  such as OP-TEE/TrustZone). I'm sending it separately from the other
  arm-soc driver changes to give it a little more visibility, once the
  subsystem is merged, we will likely keep this in the arm₋soc drivers
  branch or have the maintainers submit pull requests directly,
  depending on the patch volume.

  I have reviewed earlier versions in the past, and have reviewed the
  latest version in person during Linaro Connect BUD17.

  Here is my overall assessment of the subsystem:

   - There is clearly demand for this, both for the generic
     infrastructure and the specific OP-TEE implementation.

   - The code has gone through a large number of reviews, and the review
     comments have all been addressed, but the reviews were not coming
     up with serious issues any more and nobody volunteered to vouch for
     the quality.

   - The user space ioctl interface is sufficient to work with the
     OP-TEE driver, and it should in principle work with other TEE
     implementations that follow the GlobalPlatform[1] standards, but it
     might need to be extended in minor ways depending on specific
     requirements of future TEE implementations

   - The main downside of the API to me is how the user space is tied to
     the TEE implementation in hardware or firmware, but uses a generic
     way to communicate with it. This seems to be an inherent problem
     with what it is trying to do, and I could not come up with any
     better solution than what is implemented here.

  For a detailed history of the patch series, see

    https://lkml.org/lkml/2017/3/10/1277"

* tag 'armsoc-tee' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: dt: hikey: Add optee node
  Documentation: tee subsystem and op-tee driver
  tee: add OP-TEE driver
  tee: generic TEE subsystem
  dt/bindings: add bindings for optee

Pull more power management updates from Rafael Wysocki:
 "These add new CPU IDs to a couple of drivers, fix a possible NULL
  pointer dereference in the cpuidle core, update DT-related things in
  the generic power domains framework and finally update the
  suspend/resume infrastructure to improve the handling of wakeups from
  suspend-to-idle.

  Specifics:

   - Add Intel Gemini Lake CPU IDs to the intel_idle and intel_rapl
     drivers (David Box).

   - Add a NULL pointer check to the cpuidle core to prevent it from
     crashing on platforms with incomplete cpuidle configuration (Fei
     Li).

   - Fix DT-related documentation in the generic power domains (genpd)
     framework and add a MAINTAINERS entry for DT-related material in
     genpd (Viresh Kumar).

   - Update the system suspend/resume infrastructure to improve the
     handling of aborts of suspend transitions in progress in the wakeup
     framework and rework the suspend-to-idle core loop to make it
     possible to filter out spurious wakeup events (specifically the
     ones coming from ACPI) without resuming all the way up to user
     space every time (Rafael Wysocki)"

* tag 'pm-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / sleep: Ignore spurious SCI wakeups from suspend-to-idle
  PM / wakeup: Integrate mechanism to abort transitions in progress
  x86/intel_idle: add Gemini Lake support
  cpuidle: check dev before usage in cpuidle_use_deepest_state()
  powercap: intel_rapl: Add support for Gemini Lake
  PM / Domains: Add DT file to MAINTAINERS
  PM / Domains: Fix DT example