linux-toradex.git/Documentation/hwmon/w83627hf, branch v3.2.2

hwmon: (w83627hf) Document W83627THF voltage pin mapping

2011-01-12T20:55:11+00:00

I had to look it up for one user, so we might as well store it in the
driver documentation.

Signed-off-by: Jean Delvare 
Acked-by: Guenter Roeck

Documentation: update broken web addresses.

2010-08-04T13:21:40+00:00

Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.

Signed-off-by: Justin P. Mattock 
Signed-off-by: Thomas Weber 
Signed-off-by: Mike Frysinger 
Cc: Paulo Marques 
Cc: Randy Dunlap 
Cc: Michael Neuling 
Signed-off-by: Jiri Kosina

hwmon: (w83627hf) Drop the force_addr module parameter

2009-12-09T19:35:48+00:00

This module parameter is there to workaround broken BIOS. I'm not even
sure if it was used in the past 5 years, and it gets in the way of
converting the driver to the MFD infrastructure. So tell the users how
they can do the same from user-space.

Signed-off-by: Jean Delvare 
Cc: Rodolfo Giometti

hwmon: (w83627hf) Drop reset module parameter

2008-08-06T20:41:04+00:00

Drop the reset parameter of the w83627hf driver. It seems it wasn't
that useful. It was dropped from the Linux 2.4 version of this driver
back in July 2004.

The only users who have reported that they were still using this
parameter, needed it to switch the chip from automatic fan speed
control back to manual mode. Now that the driver creates pwmN_enable
sysfs files, users will be able to use these files instead, which is
way less agressive.

Signed-off-by: Jean Delvare 
Acked-by: Dominik Geyer

hwmon: Update the lm-sensors website address

2008-02-08T01:39:42+00:00

It's about time to reflect the move of the lm-sensors project to
lm-sensors.org.

Signed-off-by: Jean Delvare 
Signed-off-by: Mark M. Hoffman

[PATCH] hwmon: Add support for the Winbond W83687THF

2006-03-23T22:21:52+00:00

Add support for the Winbond W83687THF chip to the w83627hf hardware
monitoring driver. This new chip is almost similar to the already
supported W83627THF chip, except for VID and a few other minor
changes.

Signed-off-by: Jean Delvare 
Signed-off-by: Greg Kroah-Hartman

[PATCH] w83627hf: Document the reset module parameter

2006-02-14T06:30:09+00:00

Document the reset module parameter which was recently added to the
w83627hf driver.

Signed-off-by: Jean Delvare 
Signed-off-by: Greg Kroah-Hartman

[PATCH] hwmon: Clarify the W83627THF VID documentation

2006-01-06T06:16:20+00:00

This patch clarifies the W83627THF VID documentation.

Signed-off-by: Mark M. Hoffman 
Signed-off-by: Jean Delvare 
Signed-off-by: Greg Kroah-Hartman

[PATCH] I2C: Move hwmon drivers (3/3)

2005-07-11T21:47:41+00:00

Part 3: Move the drivers documentation, plus two general documentation
files.

Note that the patch "adds trailing whitespace", because it does move the
files as-is, and some files happen to have trailing whitespace.

Signed-off-by: Jean Delvare 
Signed-off-by: Greg Kroah-Hartman