linux-toradex.git/arch/arc, branch v5.9-rc5

Merge tag 'arc-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc

2020-09-05T20:46:14+00:00

Pull ARC fixes from Vineet Gupta:

 - HSDK-4xd Dev system: perf driver updates for sampling interrupt

 - HSDK* Dev System: Ethernet broken [Evgeniy Didin]

 - HIGHMEM broken (2 memory banks) [Mike Rapoport]

 - show_regs() rewrite once and for all

 - Other minor fixes

* tag 'arc-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [plat-hsdk]: Switch ethernet phy-mode to rgmii-id
  arc: fix memory initialization for systems with two memory banks
  irqchip/eznps: Fix build error for !ARC700 builds
  ARC: show_regs: fix r12 printing and simplify
  ARC: HSDK: wireup perf irq
  ARC: perf: don't bail setup if pct irq missing in device-tree
  ARC: pgalloc.h: delete a duplicated word + other fixes

ARC: [plat-hsdk]: Switch ethernet phy-mode to rgmii-id

2020-09-01T18:59:04+00:00

HSDK board has Micrel KSZ9031, recent commit
bcf3440c6dd ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
caused a breakdown of Ethernet.
Using 'phy-mode = "rgmii"' is not correct because accodring RGMII
specification it is necessary to have delay on RX (PHY to MAX)
which is not generated in case of "rgmii".
Using "rgmii-id" adds necessary delay and solves the issue.

Also adding name of PHY placed on HSDK board.

Signed-off-by: Evgeniy Didin 
Cc: Eugeniy Paltsev 
Cc: Alexey Brodkin 
Signed-off-by: Vineet Gupta

arc: fix memory initialization for systems with two memory banks

2020-09-01T18:23:50+00:00

Rework of memory map initialization broke initialization of ARC systems
with two memory banks. Before these changes, memblock was not aware of
nodes configuration and the memory map was always allocated from the
"lowmem" bank. After the addition of node information to memblock, the core
mm attempts to allocate the memory map for the "highmem" bank from its
node. The access to this memory using __va() fails because it can be only
accessed using kmap.

Anther problem that was uncovered is that {min,max}_high_pfn are calculated
from u64 high_mem_start variable which prevents truncation to 32-bit
physical address and the PFN values are above the node and zone boundaries.

Use phys_addr_t type for high_mem_start and high_mem_size to ensure
correspondence between PFNs and highmem zone boundaries and reserve the
entire highmem bank until mem_init() to avoid accesses to it before highmem
is enabled.

To test this:
1. Enable HIGHMEM in ARC config
2. Enable 2 memory banks in haps_hs.dts (uncomment the 2nd bank)

Fixes: 51930df5801e ("mm: free_area_init: allow defining max_zone_pfn in descending order")
Cc: stable@vger.kernel.org   [5.8]
Signed-off-by: Mike Rapoport 
Signed-off-by: Vineet Gupta 
[vgupta: added instructions to test highmem]

irqchip/eznps: Fix build error for !ARC700 builds

2020-08-27T20:15:17+00:00

eznps driver is supposed to be platform independent however it ends up
including stuff from inside arch/arc headers leading to rand config
build errors.

The quick hack to fix this (proper fix is too much chrun for non active
user-base) is to add following to nps platform agnostic header.
 - copy AUX_IENABLE from arch/arc header
 - move CTOP_AUX_IACK from arch/arc/plat-eznps/*/**

Reported-by: kernel test robot 
Reported-by: Sebastian Andrzej Siewior 
Link: https://lkml.kernel.org/r/20200824095831.5lpkmkafelnvlpi2@linutronix.de
Signed-off-by: Vineet Gupta

ARC: show_regs: fix r12 printing and simplify

2020-08-27T20:11:37+00:00

when working on ARC64, spotted an issue in ARCv2 reg file printing.
print_reg_file() assumes contiguous reg-file whereas in ARCv2 they are
not: r12 comes before r0-r11 due to hardware auto-save. Apparently this
issue has been present since v2 port submission.

To avoid bolting hacks for this discontinuity while looping through
pt_regs, just ditching the loop and print pt_regs directly.

Signed-off-by: Vineet Gupta

treewide: Use fallthrough pseudo-keyword

2020-08-23T22:36:59+00:00

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva

ARC: HSDK: wireup perf irq

2020-08-17T04:36:15+00:00

Newer version of HSDK aka HSDK-4xD (with dual issue HS48x4 CPU) wired up
the perf interrupt, so enable that in DT.
This is OK for old HSDK where this irq is ignored because pct irq is not
wired up in hardware.

Signed-off-by: Vineet Gupta

ARC: perf: don't bail setup if pct irq missing in device-tree

2020-08-17T04:36:15+00:00

Current code inadventely bails if hardware supports sampling/overflow
interrupts, but the irq is missing from device tree.

|
| # perf stat -e cycles,instructions,major-faults,minor-faults ../hackbench
| Running with 10 groups 400 process
| Time: 0.921
|
| Performance counter stats for '../hackbench':
|
|         cycles
|         instructions
|                 0      major-faults
|              8679      minor-faults

This need not be as we can still do simple counting based perf stat.
This unborks perf on HSDK-4xD

Cc: 
Signed-off-by: Vineet Gupta

ARC: pgalloc.h: delete a duplicated word + other fixes

2020-08-17T04:36:15+00:00

Drop the repeated word "to".
Change "Thay" to "That".
Add a closing right parenthesis.

Signed-off-by: Randy Dunlap 
Cc: Vineet Gupta 
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Vineet Gupta

mm/gup: remove task_struct pointer for all gup code

2020-08-12T17:58:04+00:00

After the cleanup of page fault accounting, gup does not need to pass
task_struct around any more.  Remove that parameter in the whole gup
stack.

Signed-off-by: Peter Xu 
Signed-off-by: Andrew Morton 
Reviewed-by: John Hubbard 
Link: http://lkml.kernel.org/r/20200707225021.200906-26-peterx@redhat.com
Signed-off-by: Linus Torvalds