Pull ARM SoC fixes from Arnd Bergmann:
 "The code fixes in this round are all for the Texas Instruments OMAP
  platform, addressing several regressions related to the ti-sysc
  interconnect changes that was merged in linux-5.11 and one recently
  introduced RCU usage warning.

  Tero Kristo updates his maintainer file entries as he is changing to a
  new employer.

  The other changes are for devicetree files across eight different
  platforms:

  TI OMAP:
   - multiple gpio related one-line fixes

  Allwinner/sunxi:
   - ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
   - soc: sunxi: mbus: Remove DE2 display engine compatibles

  NXP lpc32xx:
   - ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL

  STMicroelectronics stm32
   - multiple minor fixes for DHCOM/DHCOR boards

  NXP Layerscape:
   - Fix DCFG address range on LS1046A SoC

  Amlogic meson:
   - fix reboot issue on odroid C4
   - revert an ethernet change that caused a regression
   - meson-g12: Set FL-adj property value

  Rockchip:
   - multiple minor fixes on 64-bit rockchip machines

  Qualcomm:
   - Regression fixes for Lenovo Yoga touchpad and for interconnect
     configuration
   - Boot fixes for 'LPASS' clock configuration on two machines"

* tag 'arm-soc-fixes-v5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
  ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL
  ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
  arm64: dts: ls1046a: fix dcfg address range
  soc: sunxi: mbus: Remove DE2 display engine compatibles
  arm64: dts: meson: switch TFLASH_VDD_EN pin to open drain on Odroid-C4
  Revert "arm64: dts: amlogic: add missing ethernet reset ID"
  arm64: dts: rockchip: Disable display for NanoPi R2S
  ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
  arm64: dts: rockchip: remove interrupt-names property from rk3399 vdec node
  drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
  ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
  ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
  ARM: dts: stm32: Fix GPIO hog names on DHCOM
  ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
  ARM: dts: stm32: Disable WP on DHCOM uSD slot
  ARM: dts: stm32: Connect card-detect signal on DHCOM
  ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect
  arm64: dts: qcom: sdm845: Reserve LPASS clocks in gcc
  ...

One fix for a phy-mode ethernet issue, and one to fix the display output on
SoCs with the Display Engine 2

* tag 'sunxi-fixes-for-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
  soc: sunxi: mbus: Remove DE2 display engine compatibles

Link: https://lore.kernel.org/r/f8298059-f9ca-43b4-9e29-35bc0e0c9b15.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This reverts commit c17e9377aa81664d94b4f2102559fcf2a01ec8e7.

The lpc32xx clock driver is not able to actually change the PLL rate as
this would require reparenting ARM_CLK, DDRAM_CLK, PERIPH_CLK to SYSCLK,
then stop the PLL, update the register, restart the PLL and wait for the
PLL to lock and finally reparent ARM_CLK, DDRAM_CLK, PERIPH_CLK to HCLK
PLL.

Currently, the HCLK driver simply updates the registers but this has no
real effect and all the clock rate calculation end up being wrong. This is
especially annoying for the peripheral (e.g. UARTs, I2C, SPI).

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20210203090320.GA3760268@piout.net'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

BPi Pro needs TX and RX delay for Gbit to work reliable and avoid high
packet loss rates. The realtek phy driver overrides the settings of the
pull ups for the delays, so fix this for BananaPro.

Fix the phy-mode description to correctly reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").

Fixes: 10662a33dcd9 ("ARM: dts: sun7i: Add dts file for Bananapro board")
Signed-off-by: Hermann Lauer <Hermann.Lauer@uni-heidelberg.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210128111842.GA11919@lemon.iwr.uni-heidelberg.de

Pull devicetree fixes from Rob Herring:

 - Cleanups on properties with standard unit suffixes

 - Fix overwriting dma_range_map if there's no 'dma-ranges' property

 - Fix a bug when creating a /chosen node from ARM ATAGs

 - Add missing properties for TI j721e USB binding

 - Several doc reference updates due to DT schema conversions

* tag 'devicetree-fixes-for-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: Cleanup standard unit properties
  of/device: Update dma_range_map only when dev has valid dma-ranges
  ARM: zImage: atags_to_fdt: Fix node names on added root nodes
  dt-bindings: usb: j721e: add ranges and dma-coherent props
  dt-bindings:iio:adc: update adc.yaml reference
  dt-bindings: memory: mediatek: update mediatek,smi-larb.yaml references
  dt-bindings: display: mediatek: update mediatek,dpi.yaml reference
  ASoC: audio-graph-card: update audio-graph-card.yaml reference

Fixes for omaps for v5.11-rc cycle

The recent changes to switch SoCs to boot with ti-sysc interconnect
target module driver and genpd caused few regressions:

- The omap_prm reset driver needs to clear any reset bits deasserted by
  the bootloader or kexec boot for the three reset bit cases. Otherwise
  we can have an oops with accelerators starting to boot with potentially
  unconfigured MMU for example

- Custom kernel configs are not automatically selecting simple-pm-bus
  driver that we now need to probe interconnects so we need to select it
  always

- We are not passing legacy platform data in auxdata with simple-pm-bus
  like we do for simple-bus. We need to pass auxdata to simple-pm-bus so
  it can pass it to of_platform_populate()

Then recent RCU changes started causing splats for cpuidle44xx that now
need RCU_NONIDLE added to the calls in several places

And then we have few device specific fixes:

- We need to remove legacy spi-cs-hig for gta04 display to work, and
  set the gpio to active low

- Omap1 specific ohci-omap needs to call gpio_free()

- Droid4 needs to use padconf interrupt for the slider as the edge
  gpio interrupts may be lost for deeper idle states

* tag 'omap-for-v5.11/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
  drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
  ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
  ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
  ARM: dts; gta04: SPI panel chip select is active low
  soc: ti: omap-prm: Fix boot time errors for rst_map_012 bits 0 and 1
  ARM: OMAP1: OSK: fix ohci-omap breakage
  DTS: ARM: gta04: remove legacy spi-cs-high to make display work again

Link: https://lore.kernel.org/r/pull-1611818709-243493@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Commit 7536c7e03e74 ("of/fdt: Remove redundant kbasename function
call") exposed a bug creating DT nodes in the ATAGS to DT fixup code.
Non-existent nodes would mistaken get created with a leading '/'. The
problem was fdt_path_offset() takes a full path while creating a node
with fdt_add_subnode() takes just the basename.

Since this we only add root child nodes, we can just skip over the '/'.

Fixes: 7536c7e03e74 ("of/fdt: Remove redundant kbasename function call")
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Qi Zheng <arch0.zheng@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210126023905.1631161-1-robh@kernel.org

STM32 DT fixes for v5.11, round 1

Highlights:
-----------

 -Fixes are for DHCOM/DHCOR boards:
  - Fix DRC02 uSD card detect polarity
  - use uSD card detect on DHCOM
  - Disable uSD WP on DHCOM
  - Disable TSC2004 on DRC02
  - Fix GPIO hogs on DHCOM boards

* tag 'stm32-dt-for-v5.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
  ARM: dts: stm32: Fix GPIO hog names on DHCOM
  ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
  ARM: dts: stm32: Disable WP on DHCOM uSD slot
  ARM: dts: stm32: Connect card-detect signal on DHCOM
  ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect

Link: https://lore.kernel.org/r/b7379980-857e-736a-85d8-58e2bd300141@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

We may lose edge interrupts for gpio banks other than the first gpio
bank as they are not always powered. Instead, we must use the padconf
interrupt as that is always powered.

Note that we still also use the gpio for reading the pin state as that
can't be done with the padconf device.

Signed-off-by: Tony Lindgren <tony@atomide.com>

i.MX fixes for 5.11, round 2:

- Fix pcf2127 reset for imx7d-flex-concentrator board.
- Fix i.MX6 suspend with Thumb-2 kernel.
- Fix ethernet-phy address issue on imx6qdl-sr-som board.
- Fix GPIO3 `gpio-ranges` on i.MX8MP.
- Select SOC_BUS for IMX_SCU driver to fix build issue.

* tag 'imx-fixes-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  firmware: imx: select SOC_BUS to fix firmware build
  arm64: dts: imx8mp: Correct the gpio ranges of gpio3
  ARM: dts: imx6qdl-sr-som: fix some cubox-i platforms
  ARM: imx: build suspend-imx6.S with arm instruction set
  ARM: dts: imx7d-flex-concentrator: fix pcf2127 reset

Link: https://lore.kernel.org/r/20210119091949.GD4356@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>