A recent move to rid header files which were hindering multiplatform
support forced address allocations out of the headers and into the
files which were using them. We also lost some useful macros such as
IO_ADDRESS(), so physical -> virtual addressing has been carried out
manually in this case. Unfortunately the incorrect value was converted.
This patch rectifies the error and ensures earlyprintk works again.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
 "This is the third and smallest of the SoC specific updates.  Changes
  include:

   - SMP support for the Xilinx zynq platform
   - Smaller imx changes
   - LPAE support for mvebu
   - Moving the orion5x, kirkwood, dove and mvebu platforms to a common
     "mbus" driver for their internal devices.

  It would be good to get feedback on the location of the "mbus" driver.
  Since this is used on multiple platforms may potentially get shared
  with other architectures (powerpc and arm64), it was moved to
  drivers/bus/.  We expect other similar drivers to get moved to the
  same place in order to avoid creating more top-level directories under
  drivers/ or cluttering up the messy drivers/misc/ even more."

* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
  ARM: imx: reset_controller may be disabled
  ARM: mvebu: Align the internal registers virtual base to support LPAE
  ARM: mvebu: Limit the DMA zone when LPAE is selected
  arm: plat-orion: remove addr-map code
  arm: mach-mv78xx0: convert to use the mvebu-mbus driver
  arm: mach-orion5x: convert to use mvebu-mbus driver
  arm: mach-dove: convert to use mvebu-mbus driver
  arm: mach-kirkwood: convert to use mvebu-mbus driver
  arm: mach-mvebu: convert to use mvebu-mbus driver
  ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
  ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
  ARM i.MX53: make tve_ext_sel propagate rate change to PLL
  ARM i.MX53: Remove unused tve_gate clkdev entry
  ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
  ARM: i.MX5: Add PATA and SRTC clocks
  ARM: imx: do not bring up unavailable cores
  ARM: imx: add initial imx6dl support
  ARM: imx1: mm: add call to mxc_device_init
  ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
  ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
  ...

Pull ARM SoC board specific changes (part 1) from Olof Johansson:
 "These changes are all for board specific files.  These used to make up
  a large portion of the ARM changes in the past, but as we are
  generalizing the support and moving to device tree probing, this has
  gotten significantly smaller.

  The only platform actually adding new code here at the moment is
  Renesas shmobile, as they are still busy converting their code to
  device tree and have not come far enough to not need it."

* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
  ARM: msm: USB_MSM_OTG needs USB_PHY
  ARM: davinci: da850 evm: fix const qualifier placement
  ARM: davinci: da850 board: add remoteproc support
  ARM: pxa: move debug uart code
  ARM: pxa: select PXA935 on saar & tavorevb
  ARM: mmp: add more compatible names in gpio driver
  ARM: pxa: move PXA_GPIO_TO_IRQ macro
  ARM: pxa: remove cpu_is_xxx in gpio driver
  ARM: Kirkwood: update Network Space Mini v2 description
  ARM: Kirkwood: DT board setup for CloudBox
  ARM: Kirkwood: sort board entries by ASCII-code order
  ARM: OMAP: board-4430sdp: Provide regulator to pwm-backlight
  ARM: OMAP: zoom: Use pwm stack for lcd and keyboard backlight
  ARM: OMAP2+: omap2plus_defconfig: Add support for BMP085 pressure sensor
  omap2+: Remove useless Makefile line
  omap2+: Remove useless Makefile line
  ARM: OMAP: RX-51: add missing regulator supply definitions for lis3lv02d
  ARM: OMAP1: fix omap_udc registration
  ARM: davinci: use is IS_ENABLED macro
  ARM: kirkwood: add MACH_GURUPLUG_DT to defconfig
  ...

Pull ARM updates from Russell King:
 "The major items included in here are:

   - MCPM, multi-cluster power management, part of the infrastructure
     required for ARMs big.LITTLE support.

   - A rework of the ARM KVM code to allow re-use by ARM64.

   - Error handling cleanups of the IS_ERR_OR_NULL() madness and fixes
     of that stuff for arch/arm

   - Preparatory patches for Cortex-M3 support from Uwe Kleine-König.

  There is also a set of three patches in here from Hugh/Catalin to
  address freeing of inappropriate page tables on LPAE.  You already
  have these from akpm, but they were already part of my tree at the
  time he sent them, so unfortunately they'll end up with duplicate
  commits"

* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits)
  ARM: EXYNOS: remove unnecessary use of IS_ERR_VALUE()
  ARM: IMX: remove unnecessary use of IS_ERR_VALUE()
  ARM: OMAP: use consistent error checking
  ARM: cleanup: OMAP hwmod error checking
  ARM: 7709/1: mcpm: Add explicit AFLAGS to support v6/v7 multiplatform kernels
  ARM: 7700/2: Make cpu_init() notrace
  ARM: 7702/1: Set the page table freeing ceiling to TASK_SIZE
  ARM: 7701/1: mm: Allow arch code to control the user page table ceiling
  ARM: 7703/1: Disable preemption in broadcast_tlb*_a15_erratum()
  ARM: mcpm: provide an interface to set the SMP ops at run time
  ARM: mcpm: generic SMP secondary bringup and hotplug support
  ARM: mcpm_head.S: vlock-based first man election
  ARM: mcpm: Add baremetal voting mutexes
  ARM: mcpm: introduce helpers for platform coherency exit/setup
  ARM: mcpm: introduce the CPU/cluster power API
  ARM: multi-cluster PM: secondary kernel entry code
  ARM: cacheflush: add synchronization helpers for mixed cache state accesses
  ARM: cpu hotplug: remove majority of cache flushing from platforms
  ARM: smp: flush L1 cache in cpu_die()
  ARM: tegra: remove tegra specific cpu_disable()
  ...

These patches get us closer to adding multiplatform support on
the Exynos platform, they are part of a longer series of
patches.  This would get all the simple stuff out of the
way, and I don't think there is a big risk of introducing
regressions with these.

A lot of the other patches have already been merged into
subsystem trees. After this series in in arm-soc, what is
left comes down to

* The ASoC conversion to dmaengine won't make it unless someone
  who knows that code better steps up to do it right away. This
  means that we won't have audio in a 3.10 multiplatform kernel
  on Exynos, but it will still work for users that don't enable
  multiplatform.

* The irqchip (combiner), clk and clksource patches are all based
  on top   of other changesets we pulled in from your trees, so I
  would not make them part of the next/multiplatform branch. We can
  apply them on top of the next/drivers branch once they are
  tested successfully.

* A trivial patch is needed in the end to actually make
  CONFIG_ARCH_EXYNOS visible in multiplatform configurations.
  We will do that as a separate patch once everything else is
  there.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The move is necessary to support early debug output on exynos
with multiplatform configurations. This implies also moving the
plat/debug-macro.S file, but we are leaving the remaining users of that
file in place, to avoid adding large numbers of extra configuration
options to Kconfig.debug

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

In order to be able to support the LPAE, the internal registers
virtual base must be aligned to 2MB. In LPAE section size is 2MB, in
earlyprintk we map the internal registers and it must be section
aligned.

Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Move debug uart code from mach-pxa/mach-mmp to debug directory.
Since they are similar, merge them together.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Eric Mico <eric.y.miao@gmail.com>

From Shawn Guo <shawn.guo@linaro.org>:

The mxs multiplatform support for 3.10:

* It enables the multiplatform build for mach-mxs platform.

* tag 'mxs-multiplatform-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mxs: enable multiplatform build
  ARM: mxs: rename debug-macro.S for multiplatform build
  ARM: mxs: call mxs_pm_init() as a machine_desc hook

Conflicts:
	arch/arm/Kconfig.debug

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

From Linus Walleij <linus.walleij@linaro.org>:

Ux500 multiplatform support.  This tag builds upon the MFD-specific base
tag "ux500-multiplatform-mfd". This removes all <mach/*> dependencies
and makes the ux500 fully multi-platform.

* tag 'ux500-multiplatform-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: ux500: build hotplug.o for ARMv7-a
  ARM: ux500: move to multiplatform
  ARM: ux500: make remaining headers local
  ARM: ux500: make irqs.h local to platform
  ARM: ux500: get rid of <mach/[hardware|db8500-regs].h>
  staging: ste_rmi4: kill platform_data hack
  ARM: ux500: move mach/msp.h to <linux/platform_data/*>
  clk: ux500: pass clock base adresses in init call
  ARM: ux500: make debug macro stand-alone
  ARM: ux500: move debugmacro to debug includes
  ARM: ux500: split out prcmu initialization
  mfd: db8500-prcmu: drop unused includes
  ARM: ux500: move PM-related PRCMU functions to machine
  mfd: db8500-prcmu: get base address from resource
  mfd: prcmu: pass a base and size with the early initcall

Conflicts:
	arch/arm/Kconfig

Signed-off-by: Arnd Bergmann <arnd@arndb.de>