commit 6571534b600b8ca1936ff5630b9e0947f21faf16 upstream.

To configure pads during the initialisation a set of special constants
is used, e.g.
#define MX25_PAD_FEC_MDIO__FEC_MDIO IOMUX_PAD(0x3c4, 0x1cc, 0x10, 0, 0, PAD_CTL_HYS | PAD_CTL_PUS_22K_UP)

The problem is that no pull-up/down is getting activated unless both
PAD_CTL_PUE (pull-up enable) and PAD_CTL_PKE (pull/keeper module
enable) set. This is clearly stated in the i.MX25 datasheet and is
confirmed by the measurements on hardware. This leads to some rather
hard to understand bugs such as misdetecting an absent ethernet PHY (a
real bug i had), unstable data transfer etc. This might affect mx25,
mx35, mx50, mx51 and mx53 SoCs.

It's reasonable to expect that if the pullup value is specified, the
intention was to have it actually active, so we implicitly add the
needed bits.

Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Commit fad107086d5a869c1c07e5bb35b7b57a10ecf578 fixed the wrong test for MX51
as the MX51 addresses are wrong for MX50 and MX53 but now it's MX51 only,
UART_PADDR is not defined anymore when building for MX50/MX53.

Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Steev Klimaszewski <steev@genesi-usa.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

It might be not good to use software defined version to identify sdma
device type, when hardware does not define such version.  Instead,
soc name is stable enough to define the device type.

The patch uses platform_device_id rather than version number passed
by platform data to identify sdma device type/version.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Vinod Koul <vinod.koul@intel.com>

The patch removes all the uses of cpu_is_mx().  Instead, it utilizes
platform_device_id to distinguish the esdhc differences among SoCs.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>

The patch extends card_detect and write_protect support to get mx5
family and more scenarios supported.  The changes include:

 * Turn platform_data from optional to mandatory
 * Add cd_types and wp_types into platform_data to cover more use
   cases
 * Remove the use of flag ESDHC_FLAG_GPIO_FOR_CD
 * Adjust some machine codes to adopt the platform_data changes
 * Work around the issue that software reset will get card detection
   circuit stop working

With this patch, card_detect and write_protect gets supported on
mx5 based platforms.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Chris Ball <cjb@laptop.org>

On the recent i.mx (mx25/50/53), there is a gasket inside fec
controller which needs to be enabled no matter phy works in MII
or RMII mode.

The current code enables the gasket only when phy interface is RMII.
It's broken when the driver works with a MII phy.  The patch uses
platform_device_id to distinguish the SoCs that have the gasket and
enables it on these SoCs for both MII and RMII mode.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reported-by: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>

* 'next/devel' of ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (128 commits)
  ARM: S5P64X0: External Interrupt Support
  ARM: EXYNOS4: Enable MFC on Samsung NURI
  ARM: EXYNOS4: Enable MFC on universal_c210
  ARM: S5PV210: Enable MFC on Goni
  ARM: S5P: Add support for MFC device
  ARM: EXYNOS4: Add support FIMD on SMDKC210
  ARM: EXYNOS4: Add platform device and helper functions for FIMD
  ARM: EXYNOS4: Add resource definition for FIMD
  ARM: EXYNOS4: Change devname for FIMD clkdev
  ARM: SAMSUNG: Add IRQ_I2S0 definition
  ARM: SAMSUNG: Add platform device for idma
  ARM: EXYNOS4: Add more registers to be saved and restored for PM
  ARM: EXYNOS4: Add more register addresses of CMU
  ARM: EXYNOS4: Add platform device for dwmci driver
  ARM: EXYNOS4: configure rtc-s3c on NURI
  ARM: EXYNOS4: configure MAX8903 secondary charger on NURI
  ARM: EXYNOS4: configure ADC on NURI
  ARM: EXYNOS4: configure MAX17042 fuel gauge on NURI
  ARM: EXYNOS4: configure regulators and PMIC(MAX8997) on NURI
  ARM: EXYNOS4: Increase NR_IRQS for devices with more IRQs
  ...

Fix up tons of silly conflicts:
 - arch/arm/mach-davinci/include/mach/psc.h
 - arch/arm/mach-exynos4/Kconfig
 - arch/arm/mach-exynos4/mach-smdkc210.c
 - arch/arm/mach-exynos4/pm.c
 - arch/arm/mach-imx/mm-imx1.c
 - arch/arm/mach-imx/mm-imx21.c
 - arch/arm/mach-imx/mm-imx25.c
 - arch/arm/mach-imx/mm-imx27.c
 - arch/arm/mach-imx/mm-imx31.c
 - arch/arm/mach-imx/mm-imx35.c
 - arch/arm/mach-mx5/mm.c
 - arch/arm/mach-s5pv210/mach-goni.c
 - arch/arm/mm/Kconfig

* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  ARM: Consolidate the clkdev header files
  ARM: set vga memory base at run-time
  ARM: convert PCI defines to variables
  ARM: pci: make pcibios_assign_all_busses use pci_has_flag
  ARM: remove unnecessary mach/hardware.h includes
  pci: move microblaze and powerpc pci flag functions into asm-generic
  powerpc: rename ppc_pci_*_flags to pci_*_flags

Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h

I2C signals SDA/SCL are a bit different, they need to be pull-up and
open-drain (so to support multiple I2C devices).

Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>