Zyxel EX3510-B is a WiFi 6 capable home gateway (family) based on the
BCM4906 SoC, with 512MiB of RAM and 512MiB of NAND flash. WiFi support
consists of a BCM6710 and a BCM6715 attached to separate PCIe buses.

Add an initial devicetree for this system, with support for:
- Onboard UART (per base dtsi)
- USB (2.0 only; superspeed devices are treated as high-speed due to an
    unknown cause)
- Both buttons (rear reset, front WPS)
- Almost all LEDs:
  - Power (red/green)
  - Internet (red/green)
  - WAN (green)
  - LAN (green; anode is connected to GPIO 13 so currently
      nonfunctioning)
  - USB (green)
  - WPS button (red/green)
  - Absent in DT: There are 2.4GHz/5.0GHz WiFi status LEDs connected to
      the WiFi chips instead of the SoC.
- NAND flash
- Embedded Ethernet switch
- Factory-programmed Ethernet MAC address

WiFi cannot be enabled at this time due to Linux lacking drivers for
both the PCIe controllers and the PCIe WiFi peripherals.

Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Link: https://lore.kernel.org/r/20241009215454.1449508-3-CFSworks@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>

Add generic bare bone bcm94908.dts file to support any 4908 based
design. It supports cpu subsystem, memory and an uart console. This can
be useful for board bring-up and cpu subsystem and memory related kernel
test as well.

Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20220803175455.47638-6-william.zhang@broadcom.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

As part of ARCH_BCM4908 to ARCH_BCMBCA migration, move the BCM4908 dts
files to bcmbca folder and use CONFIG_ARCH_BCMBCA to build all the
BCM4908 board dts. Delete bcm4908 folder and its makefile as well.

Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20220803175455.47638-5-william.zhang@broadcom.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

It's a home router with 1 GiB of RAM, 6 Ethernet ports, 2 USB ports.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20220713200351.28526-2-zajec5@gmail.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add DTS for ARMv8 based broadband SoC BCM6813. bcm6813.dtsi is the
SoC description DTS header and bcm96813.dts is a simple DTS file for
Broadcom BCM96813 Reference board that only enable the UART port.

Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add DTS for ARMv8 based broadband SoC BCM6856. bcm6856.dtsi is the
SoC description DTS header and bcm96856.dts is a simple DTS file for
Broadcom BCM96956 Reference board that only enable the UART port.

Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add DTS for ARMv8 based broadband SoC BCM63146. bcm63146.dtsi is the
SoC description DTS header and bcm963146.dts is a simple DTS file for
Broadcom BCM963146 Reference board that only enable the UART port.

Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add DTS for ARMv8 based broadband SoC BCM6858. bcm6858.dtsi is the SoC
description DTS header and bcm96858.dts is a simple DTS file for
Broadcom BCM96858 Reference board that only enables the UART port.

Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add DTS for ARMv8 based broadband SoC BCM4912. bcm4912.dtsi is the
SoC description DTS header and bcm94912.dts is a simple DTS file for
Broadcom BCM94912 Reference board that only enable the UART port.

Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add DTS for ARMv8 based broadband SoC BCM63158. bcm63158.dtsi is the
SoC description DTS header and bcm963158.dts is a simple DTS file for
Broadcom BCM963158 Reference board that only enable the UART port.

Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>