Pull ARM SoC fixes from Olof Johansson:
 "I've been sitting on these longer than I meant, so the patch count is
  a bit higher than ideal for this part of the release. There's also
  some reverts of double-applied patches that brings the diffstat up a
  bit.

  With that said, the biggest changes are:

   - Revert of duplicate i2c device addition on two Aspeed (BMC)
     Devicetrees.

   - Move of two device nodes that got applied to the wrong part of the
     tree on ASpeed G6.

   - Regulator fix for Beaglebone X15 (adding 12/5V supplies)

   - Use interrupts for keys on Amlogic SM1 to avoid missed polls

  In addition to that, there is a collection of smaller DT fixes:

   - Power supply assignment fixes for i.MX6

   - Fix of interrupt line for magnetometer on i.MX8 Librem5 devkit

   - Build fixlets (selects) for davinci/omap2+

   - More interrupt number fixes for Stratix10, Amlogic SM1, etc.

   - ... and more similar fixes across different platforms

  And some non-DT stuff:

   - optee fix to register multiple shared pages properly

   - Clock calculation fixes for MMP3

   - Clock fixes for OMAP as well"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
  MAINTAINERS: Add myself as the co-maintainer for Actions Semi platforms
  ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
  ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
  ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
  ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
  ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
  ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
  ARM: omap2plus: select RESET_CONTROLLER
  ARM: davinci: select CONFIG_RESET_CONTROLLER
  ARM: dts: aspeed: rainier: Fix fan fault and presence
  ARM: dts: aspeed: rainier: Remove duplicate i2c busses
  ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
  ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
  ARM: dts: aspeed: tacoma: Fix fsi master node
  ARM: dts: aspeed-g6: Fix FSI master location
  ARM: dts: mmp3: Fix the TWSI ranges
  clk: mmp2: Fix the order of timer mux parents
  ARM: mmp: do not divide the clock rate
  arm64: dts: rockchip: Fix IR on Beelink A1
  optee: Fix multi page dynamic shm pool alloc
  ...

A couple of fixes for GPIO polarity and regulators on the A64
olinuxino.

* tag 'sunxi-fixes-for-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun8i: a83t: Correct USB3503 GPIOs polarity
  arm64: dts: allwinner: a64: olinuxino: Fix SDIO supply regulator
  arm64: dts: allwinner: a64: olinuxino: Fix eMMC supply regulator

Link: https://lore.kernel.org/r/582f4fda-38af-43e8-af58-957aee5b9dd8.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>

i.MX fixes for 5.5, round 2:

 - Fix i.MX8MM SDMA1 AHB clock setting to remove a "Timeout waiting for CH0"
   error seen with UART1.
 - Correct compatible of RV3029 RTC device on imx6q-dhcom board.
 - Correct interrupt trigger type for magnetometer on board
   imx8mq-librem5-devkit.
 - A series from Anson Huang to fix vdd3p0 power supplier for a few NXP
   development board.
 - Fix imx6q-icore-mipi board to use 1.5 version of i.Core MX6DL, so
   that Ethernet interface on the board works properly.
 - Fix Toradex Colibri board to get NAND flash support back.
 - Fix SGTL5000 VDDIO regulator connection for imx6q-dhcom, which
   is connected to PMIC SW2 output rather than a fixed 3V3 rail.
 - Fix 'reg' of CPU node on imx7ulp to get rid of a warning given by
   kernel.
 - Fix endian setting for DCFG on LS1028A SoC, so that register access
   of DCFG becomes correct.

* tag 'imx-fixes-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
  ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
  ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
  ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
  ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
  ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
  arm64: dts: imx8mq-librem5-devkit: use correct interrupt for the magnetometer
  ARM: dts: imx6q-dhcom: Fix SGTL5000 VDDIO regulator connection
  ARM: dts: imx7ulp: fix reg of cpu node
  arm64: dts: imx8mm: Change SDMA1 ahb clock for imx8mm
  arm64: dts: ls1028a: fix endian setting for dcfg
  ARM: dts: imx6q-dhcom: fix rtc compatible

Link: https://lore.kernel.org/r/20200110011836.GW4456@T480
Signed-off-by: Olof Johansson <olof@lixom.net>

arm-soc: Amlogic fixes for v5.5-rc

* tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  arm64: dts: meson-sm1-sei610: add gpio bluetooth interrupt
  dt-bindings: reset: meson8b: fix duplicate reset IDs
  soc: amlogic: meson-ee-pwrc: propagate errors from pm_genpd_init()
  soc: amlogic: meson-ee-pwrc: propagate PD provider registration errors
  ARM: dts: meson8: fix the size of the PMU registers
  arm64: dts: meson-sm1-sei610: gpio-keys: switch to IRQs

Link: https://lore.kernel.org/r/7hmuaweavi.fsf@baylibre.com
Signed-off-by: Olof Johansson <olof@lixom.net>

Turns out when introducing the eMMC version the gpmi node required for
NAND flash support got enabled exclusively on Colibri iMX7D 512MB.

Fixes: f928a4a377e4 ("ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) support")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 96a9169cf621 ("ARM: dts: imx6sll-evk: Assign corresponding power supply for vdd3p0")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 3feea8805d6f ("ARM: dts: imx6sl-evk: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 37a4bdead109 ("ARM: dts: imx6sx-sdb: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 93385546ba36 ("ARM: dts: imx6qdl-sabresd: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.

With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver

While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY

Similar fix has merged for i.Core MX6Q but missed to update for DL.

Fixes: a8039f2dd089 ("ARM: dts: imx6dl: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>