[Ralf: Remove a forgotten -Werror in Pb1200 Makefile.]

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1319/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Create own directory for DB1200 code and update it with new features.

- SPI support:
  - tmp121 temperature sensor
  - SPI flash on DB1200
- I2C support
  - NE1619 sensor
  - AT24 eeprom
- I2C/SPI can be selected at boot time via switch S6.8
- Carddetect IRQs for SD cards.
- gen_nand based NAND support.
- hexleds count sleep/wake transitions.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Warnings being suppressed, we can now turn on -Werror for boards which did
not have it already (devboards and xss1500).

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Register the PCMCIA driver on all boards supported by it,
get rid of now-unused pcmcia macros in the board headers
(and subsequently empty pb1100/pb1500 ones).

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

All Alchemy development boards have external CPLDs with a few registers
in them.  They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.

This patch
- adds a primitive facility to initialize and use these external
  registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
  functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
  headers in a central place.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Replace the current sysctl-based suspend interface with a new sysfs-
based one which also uses the Linux-2.6 suspend model.

To configure wakeup sources, a subtree for the demoboards is created
under /sys/power/db1x:

sys/
`-- power
    `-- db1x
        |-- gpio0
        |-- gpio1
        |-- gpio2
        |-- gpio3
        |-- gpio4
        |-- gpio5
        |-- gpio6
        |-- gpio7
        |-- timer
        |-- timer_timeout
        |-- wakemsk
        `-- wakesrc

The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register.  Writing '1'
enables a wakesource, 0 disables it.

The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.

The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.

For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:

echo 10 > /sys/power/db1x/timer_timeout
echo 1 > /sys/power/db1x/timer
echo mem > /sys/power/sleep

This patch also removes the homebrew CPU frequency switching code.  I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

 create mode 100644 arch/mips/alchemy/devboards/pm.c

Share some code and merge small files:
- Extract the prom init code from all devboard files (they only differ in
  memory configuration).
- Merge the irq configuration into board setup code.
- Merge smaller files into board setup code.

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

 delete mode 100644 arch/mips/alchemy/devboards/db1x00/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1000/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1000/irqmap.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1100/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1100/irqmap.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1200/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1500/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1500/irqmap.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1550/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1550/irqmap.c
 create mode 100644 arch/mips/alchemy/devboards/prom.c

This should ease sharing of common devboard code.

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>