linux-toradex.git/arch/mips/kvm, branch v4.10

KVM: MIPS: Flush KVM entry code from icache globally

2017-01-05T13:56:32+00:00

Flush the KVM entry code from the icache on all CPUs, not just the one
that built the entry code.

Signed-off-by: James Hogan 
Cc: Paolo Bonzini 
Cc: "Radim Krčmář" 
Cc: Ralf Baechle 
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc:  # 3.16.x-
Signed-off-by: Radim Krčmář

KVM: MIPS: Don't clobber CP0_Status.UX

2017-01-05T13:56:32+00:00

On 64-bit kernels, MIPS KVM will clear CP0_Status.UX to prevent the
guest (running in user mode) from accessing the 64-bit memory segments.
However the previous value of CP0_Status.UX is never restored when
exiting from the guest.

If the user process uses 64-bit addressing (the n64 ABI) this can result
in address error exceptions from the kernel if it needs to deliver a
signal before returning to user mode, as the kernel will need to write a
sigframe to high user addresses on the user stack which are disallowed
by CP0_Status.UX=0.

This is fixed by explicitly setting SX and UX again when exiting from
the guest, and explicitly clearing those bits when returning to the
guest. Having the SX and UX bits set when handling guest exits (rather
than only when exiting to userland) will be helpful when we support VZ,
since we shouldn't need to directly read or write guest memory, so it
will be valid for cache management IPIs to access host user addresses.

Signed-off-by: James Hogan 
Cc: Paolo Bonzini 
Cc: "Radim Krčmář" 
Cc: Ralf Baechle 
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc:  # 4.8.x-
Signed-off-by: Radim Krčmář

KVM: MIPS: Precalculate MMIO load resume PC

2016-10-26T11:43:55+00:00

The advancing of the PC when completing an MMIO load is done before
re-entering the guest, i.e. before restoring the guest ASID. However if
the load is in a branch delay slot it may need to access guest code to
read the prior branch instruction. This isn't safe in TLB mapped code at
the moment, nor in the future when we'll access unmapped guest segments
using direct user accessors too, as it could read the branch from host
user memory instead.

Therefore calculate the resume PC in advance while we're still in the
right context and save it in the new vcpu->arch.io_pc (replacing the no
longer needed vcpu->arch.pending_load_cause), and restore it on MMIO
completion.

Fixes: e685c689f3a8 ("KVM/MIPS32: Privileged instruction/target branch emulation.")
Signed-off-by: James Hogan 
Cc: Paolo Bonzini 
Cc: "Radim Krčmář 
Cc: Ralf Baechle 
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc:  # 3.10.x-
Signed-off-by: Paolo Bonzini

KVM: MIPS: Make ERET handle ERL before EXL

2016-10-26T11:43:48+00:00

The ERET instruction to return from exception is used for returning from
exception level (Status.EXL) and error level (Status.ERL). If both bits
are set however we should be returning from ERL first, as ERL can
interrupt EXL, for example when an NMI is taken. KVM however checks EXL
first.

Fix the order of the checks to match the pseudocode in the instruction
set manual.

Fixes: e685c689f3a8 ("KVM/MIPS32: Privileged instruction/target branch emulation.")
Signed-off-by: James Hogan 
Cc: Paolo Bonzini 
Cc: "Radim Krčmář 
Cc: Ralf Baechle 
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc:  # 3.10.x-
Signed-off-by: Paolo Bonzini

KVM: MIPS: Fix lazy user ASID regenerate for SMP

2016-10-26T11:43:41+00:00

kvm_mips_check_asids() runs before entering the guest and performs lazy
regeneration of host ASID for guest usermode, using last_user_gasid to
track the last guest ASID in the VCPU that was used by guest usermode on
any host CPU.

last_user_gasid is reset after performing the lazy ASID regeneration on
the current CPU, and by kvm_arch_vcpu_load() if the host ASID for guest
usermode is regenerated due to staleness (to cancel outstanding lazy
ASID regenerations). Unfortunately neither case handles SMP hosts
correctly:

 - When the lazy ASID regeneration is performed it should apply to all
   CPUs (as last_user_gasid does), so reset the ASID on other CPUs to
   zero to trigger regeneration when the VCPU is next loaded on those
   CPUs.

 - When the ASID is found to be stale on the current CPU, we should not
   cancel lazy ASID regenerations globally, so drop the reset of
   last_user_gasid altogether here.

Both cases would require a guest ASID change and two host CPU migrations
(and in the latter case one of the CPUs to start a new ASID cycle)
before guest usermode could potentially access stale user pages from a
previously running ASID in the same VCPU.

Fixes: 25b08c7fb0e4 ("KVM: MIPS: Invalidate TLB by regenerating ASIDs")
Signed-off-by: James Hogan 
Cc: Paolo Bonzini 
Cc: "Radim Krčmář 
Cc: Ralf Baechle 
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini

KVM: MIPS: Add missing uaccess.h include

2016-10-18T23:37:05+00:00

MIPS KVM uses user memory accessors but mips.c doesn't directly include
uaccess.h, so include it now.

This wasn't too much of a problem before v4.9-rc1 as asm/module.h
included asm/uaccess.h, however since commit 29abfbd9cbba ("mips:
separate extable.h, switch module.h to it") this is no longer the case.

This resulted in build failures when trace points were disabled, as
trace/define_trace.h includes trace/trace_events.h only ifdef
TRACEPOINTS_ENABLED, which goes on to include asm/uaccess.h via a couple
of other headers.

Fixes: 29abfbd9cbba ("mips: separate extable.h, switch module.h to it")
Signed-off-by: James Hogan 
Cc: Paolo Bonzini 
Cc: "Radim Krčmář" 
Cc: Ralf Baechle 
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus

2016-10-15T16:26:12+00:00

Pull MIPS updates from Ralf Baechle:
 "This is the main MIPS pull request for 4.9:

  MIPS core arch code:
   - traps: 64bit kernels should read CP0_EBase 64bit
   - traps: Convert ebase to KSEG0
   - c-r4k: Drop bc_wback_inv() from icache flush
   - c-r4k: Split user/kernel flush_icache_range()
   - cacheflush: Use __flush_icache_user_range()
   - uprobes: Flush icache via kernel address
   - KVM: Use __local_flush_icache_user_range()
   - c-r4k: Fix flush_icache_range() for EVA
   - Fix -mabi=64 build of vdso.lds
   - VDSO: Drop duplicated -I*/-E* aflags
   - tracing: move insn_has_delay_slot to a shared header
   - tracing: disable uprobe/kprobe on compact branch instructions
   - ptrace: Fix regs_return_value for kernel context
   - Squash lines for simple wrapper functions
   - Move identification of VP(E) into proc.c from smp-mt.c
   - Add definitions of SYNC barrierstype values
   - traps: Ensure full EBase is written
   - tlb-r4k: If there are wired entries, don't use TLBINVF
   - Sanitise coherentio semantics
   - dma-default: Don't check hw_coherentio if device is non-coherent
   - Support per-device DMA coherence
   - Adjust MIPS64 CAC_BASE to reflect Config.K0
   - Support generating Flattened Image Trees (.itb)
   - generic: Introduce generic DT-based board support
   - generic: Convert SEAD-3 to a generic board
   - Enable hardened usercopy
   - Don't specify STACKPROTECTOR in defconfigs

  Octeon:
   - Delete dead code and files across the platform.
   - Change to use all memory into use by default.
   - Rename upper case variables in setup code to lowercase.
   - Delete legacy hack for broken bootloaders.
   - Leave maintaining the link state to the actual ethernet/PHY drivers.
   - Add DTS for D-Link DSR-500N.
   - Fix PCI interrupt routing on D-Link DSR-500N.

  Pistachio:
   - Remove ANDROID_TIMED_OUTPUT from defconfig

  TX39xx:
   - Move GPIO setup from .mem_setup() to .arch_init()
   - Convert to Common Clock Framework

  TX49xx:
   - Move GPIO setup from .mem_setup() to .arch_init()
   - Convert to Common Clock Framework

  txx9wdt:
   - Add missing clock (un)prepare calls for CCF

  BMIPS:
   - Add PW, GPIO SDHCI and NAND device node names
   - Support APPENDED_DTB
   - Add missing bcm97435svmb to DT_NONE
   - Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
   - Add DT examples for BCM63268, BCM3368 and BCM6362
   - Add support for BCM3368 and BCM6362

  PCI
   - Reduce stack frame usage
   - Use struct list_head lists
   - Support for CONFIG_PCI_DOMAINS_GENERIC
   - Make pcibios_set_cache_line_size an initcall
   - Inline pcibios_assign_all_busses
   - Split pci.c into pci.c & pci-legacy.c
   - Introduce CONFIG_PCI_DRIVERS_LEGACY
   - Support generic drivers

  CPC
   - Convert bare 'unsigned' to 'unsigned int'
   - Avoid lock when MIPS CM >= 3 is present

  GIC:
   - Delete unused file smp-gic.c

  mt7620:
   - Delete unnecessary assignment for the field "owner" from PCI

  BCM63xx:
   - Let clk_disable() return immediately if clk is NULL

  pm-cps:
   - Change FSB workaround to CPU blacklist
   - Update comments on barrier instructions
   - Use MIPS standard lightweight ordering barrier
   - Use MIPS standard completion barrier
   - Remove selection of sync types
   - Add MIPSr6 CPU support
   - Support CM3 changes to Coherence Enable Register

  SMP:
   - Wrap call to mips_cpc_lock_other in mips_cm_lock_other
   - Introduce mechanism for freeing and allocating IPIs

  cpuidle:
   - cpuidle-cps: Enable use with MIPSr6 CPUs.

  SEAD3:
   - Rewrite to use DT and generic kernel feature.

  USB:
   - host: ehci-sead3: Remove SEAD-3 EHCI code

  FBDEV:
   - cobalt_lcdfb: Drop SEAD3 support

  dt-bindings:
   -  Document a binding for simple ASCII LCDs

  auxdisplay:
   - img-ascii-lcd: driver for simple ASCII LCD displays

  irqchip i8259:
   - i8259: Add domain before mapping parent irq
   - i8259: Allow platforms to override poll function
   - i8259: Remove unused i8259A_irq_pending

  Malta:
   - Rewrite to use DT

  of/platform:
   - Probe "isa" busses by default

  CM:
   - Print CM error reports upon bus errors

  Module:
   - Migrate exception table users off module.h and onto extable.h
   - Make various drivers explicitly non-modular:
   - Audit and remove any unnecessary uses of module.h

  mailmap:
   - Canonicalize to Qais' current email address.

  Documentation:
   - MIPS supports HAVE_REGS_AND_STACK_ACCESS_API

  Loongson1C:
   - Add CPU support for Loongson1C
   - Add board support
   - Add defconfig
   - Add RTC support for Loongson1C board

  All this except one Documentation fix has sat in linux-next and has
  survived Imagination's automated build test system"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
  Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
  MIPS: ptrace: Fix regs_return_value for kernel context
  MIPS: VDSO: Drop duplicated -I*/-E* aflags
  MIPS: Fix -mabi=64 build of vdso.lds
  MIPS: Enable hardened usercopy
  MIPS: generic: Convert SEAD-3 to a generic board
  MIPS: generic: Introduce generic DT-based board support
  MIPS: Support generating Flattened Image Trees (.itb)
  MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
  MIPS: Print CM error reports upon bus errors
  MIPS: Support per-device DMA coherence
  MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
  MIPS: Sanitise coherentio semantics
  MIPS: PCI: Support generic drivers
  MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
  MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
  MIPS: PCI: Inline pcibios_assign_all_busses
  MIPS: PCI: Make pcibios_set_cache_line_size an initcall
  MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
  MIPS: PCI: Use struct list_head lists
  ...

MIPS: kvm: Audit and remove any unnecessary uses of module.h

2016-10-04T23:31:20+00:00

Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends.  That changed
when we forked out support for the latter into the export.h file.

This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig.  In the case of
kvm where it is modular, we can extend that to also include files
that are building basic support functionality but not related
to loading or registering the final module; such files also have
no need whatsoever for module.h

The advantage in removing such instances is that module.h itself
sources about 15 other headers; adding significantly to what we feed
cpp, and it can obscure what headers we are effectively using.

Since module.h was the source for init.h (for __init) and for
export.h (for EXPORT_SYMBOL) we consider each instance for the
presence of either and replace as needed.  In this case, we did
not need to add either to any files.

Signed-off-by: Paul Gortmaker 
Acked-by: James Hogan 
Acked-by: Paolo Bonzini 
Cc: "Radim Krčmář" 
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14036/
Signed-off-by: Ralf Baechle

MIPS: KVM: Use __local_flush_icache_user_range()

2016-10-04T23:31:20+00:00

Convert KVM dynamic translation of guest instructions to flush icache
for guest mapped addresses using the new
__local_flush_icache_user_range() API to allow the more generic
flush_icache_range() to be changed to work on kernel addresses only.

Signed-off-by: James Hogan 
Cc: Ralf Baechle 
Cc: Paolo Bonzini 
Cc: "Radim Krčmář" 
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14155/
Signed-off-by: Ralf Baechle

Merge tag 'kvm_mips_4.9_1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/kvm-mips into next

2016-09-29T14:26:52+00:00

MIPS KVM updates for v4.9

- A couple of fixes in preparation for supporting MIPS EVA host kernels.
- MIPS SMP host & TLB invalidation fixes.