commit 29ce3c5073057991217916abc25628e906911757 upstream.

In __after_prom_start we copy the kernel down to zero in two calls to
copy_and_flush.  After the first call (copy from 0 to copy_to_here:)
we jump to the newly copied code soon after.

Unfortunately there's no isync between the copy of this code and the
jump to it.  Hence it's possible that stale instructions could still be
in the icache or pipeline before we branch to it.

We've seen this on real machines and it's results in no console output
after:
  calling quiesce...
  returning from prom_init

The below adds an isync to ensure that the copy and flushing has
completed before any branching to the new instructions occurs.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Motivation:
IBM Blue Gene/Q comes with some very strange firmware that I'm trying to get out
of using in the kernel.  So instead I spin all the threads in the boot wrapper
(using the firmware) and have them enter the kexec stub, pre-translated at the
virtual "linear" address, never touching firmware again.

This works strategy works wonderfully, but I need the following patch in the
kexec stub. I believe it should not effect Book3S and Book3E does not appear
to be here yet so I'd love to get any criticisms up front.

This patch adds two items:

1) Book3e requires that GPR4 survive the "hold" process, so we make
   sure that happens.
2) Book3e has no real mode, and the hold code exploits this.  Since
   these processors ares always translated, we arrange for the kexeced
   threads to enter the hold code using the normal kernel linear mapping.

Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Finally remove the two level TOC and build with -mcmodel=medium.

Unfortunately we can't build modules with -mcmodel=medium due to
the tricks the kernel module loader plays with percpu data:

# -mcmodel=medium breaks modules because it uses 32bit offsets from
# the TOC pointer to create pointers where possible. Pointers into the
# percpu data area are created by this method.
#
# The kernel module loader relocates the percpu data section from the
# original location (starting with 0xd...) to somewhere in the base
# kernel percpu data space (starting with 0xc...). We need a full
# 64bit relocation for this to work, hence -mcmodel=large.

On older kernels we fall back to the two level TOC (-mminimal-toc)

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

POWER8/v2.07 allows exceptions to be taken with the MMU still on.

A new set of exception vectors is added at 0xc000_0000_0000_4xxx.  When the HW
takes us here, MSR IR/DR will be set already and we no longer need a costly
RFID to turn the MMU back on again.

The original 0x0 based exception vectors remain for when the HW can't leave the
MMU on.  Examples of this are when we can't trust the current MMU mappings,
like when we are changing from guest to hypervisor (HV 0 -> 1) or when the MMU
was off already.  In these cases the HW will take us to the original 0x0 based
exception vectors with the MMU off as before.

This uses the new macros added previously too implement these new execption
vectors at 0xc000_0000_0000_4xxx.  We exit these exception vectors using
mflr/blr (rather than mtspr SSR0/RFID), since we don't need the costly MMU
switch anymore.

This moves the __end_interrupts marker down past these new 0x4000 vectors since
they will need to be copied down to 0x0 when the kernel is not at 0x0.

Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

If we build a kernel with CONFIG_RELOCATABLE=y CONFIG_CRASH_DUMP=n,
the kernel fails when we run at a non zero offset. It turns out
we were incorrectly wrapping some of the relocatable kernel code
with CONFIG_CRASH_DUMP.

Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

OPAL provides the firmware base/entry in registers at boot time
for debugging purposes. We had a bug in the code trying to stash
these into the appropriate kernel globals (a line of code was
probably dropped by accident back when this was merged)

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The current implementation of lazy interrupts handling has some
issues that this tries to address.

We don't do the various workarounds we need to do when re-enabling
interrupts in some cases such as when returning from an interrupt
and thus we may still lose or get delayed decrementer or doorbell
interrupts.

The current scheme also makes it much harder to handle the external
"edge" interrupts provided by some BookE processors when using the
EPR facility (External Proxy) and the Freescale Hypervisor.

Additionally, we tend to keep interrupts hard disabled in a number
of cases, such as decrementer interrupts, external interrupts, or
when a masked decrementer interrupt is pending. This is sub-optimal.

This is an attempt at fixing it all in one go by reworking the way
we do the lazy interrupt disabling from the ground up.

The base idea is to replace the "hard_enabled" field with a
"irq_happened" field in which we store a bit mask of what interrupt
occurred while soft-disabled.

When re-enabling, either via arch_local_irq_restore() or when returning
from an interrupt, we can now decide what to do by testing bits in that
field.

We then implement replaying of the missed interrupts either by
re-using the existing exception frame (in exception exit case) or via
the creation of a new one from an assembly trampoline (in the
arch_local_irq_enable case).

This removes the need to play with the decrementer to try to create
fake interrupts, among others.

In addition, this adds a few refinements:

 - We no longer  hard disable decrementer interrupts that occur
while soft-disabled. We now simply bump the decrementer back to max
(on BookS) or leave it stopped (on BookE) and continue with hard interrupts
enabled, which means that we'll potentially get better sample quality from
performance monitor interrupts.

 - Timer, decrementer and doorbell interrupts now hard-enable
shortly after removing the source of the interrupt, which means
they no longer run entirely hard disabled. Again, this will improve
perf sample quality.

 - On Book3E 64-bit, we now make the performance monitor interrupt
act as an NMI like Book3S (the necessary C code for that to work
appear to already be present in the FSL perf code, notably calling
nmi_enter instead of irq_enter). (This also fixes a bug where BookE
perfmon interrupts could clobber r14 ... oops)

 - We could make "masked" decrementer interrupts act as NMIs when doing
timer-based perf sampling to improve the sample quality.

Signed-off-by-yet: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---

v2:

- Add hard-enable to decrementer, timer and doorbells
- Fix CR clobber in masked irq handling on BookE
- Make embedded perf interrupt act as an NMI
- Add a PACA_HAPPENED_EE_EDGE for use by FSL if they want
  to retrigger an interrupt without preventing hard-enable

v3:

 - Fix or vs. ori bug on Book3E
 - Fix enabling of interrupts for some exceptions on Book3E

v4:

 - Fix resend of doorbells on return from interrupt on Book3E

v5:

 - Rebased on top of my latest series, which involves some significant
rework of some aspects of the patch.

v6:
 - 32-bit compile fix
 - more compile fixes with various .config combos
 - factor out the asm code to soft-disable interrupts
 - remove the C wrapper around preempt_schedule_irq

v7:
 - Fix a bug with hard irq state tracking on native power7

This removes the various bits of assembly in the kernel entry,
exception handling and SLB management code that were specific
to running under the legacy iSeries hypervisor which is no
longer supported.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This adds a udbg and an hvc console backend for supporting a console
using the OPAL console interfaces.

On OPAL v1 we have hvc0 mapped to whatever console the system was
configured for (network or hvsi serial port) via the service
processor.

On OPAL v2 we have hvcN mapped to the Nth console provided by OPAL
which generally corresponds to:

	hvc0 : network console (raw protocol)
	hvc1 : serial port S1 (hvsi)
	hvc2 : serial port S2 (hvsi)

Note: At this point, early debug console only works with OPAL v1
and shouldn't be enabled in a normal kernel.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

On machines supporting the OPAL firmware version 1, the system
is initially booted under pHyp. We then use a special hypercall
to verify if OPAL is available and if it is, we then trigger
a "takeover" which disables pHyp and loads the OPAL runtime
firmware, giving control to the kernel in hypervisor mode.

This patch add the necessary code to detect that the OPAL takeover
capability is present when running under PowerVM (aka pHyp) and
perform said takeover to get hypervisor control of the processor.

To perform the takeover, we must first use RTAS (within Open
Firmware runtime environment) to start all processors & threads,
in order to give control to OPAL on all of them. We then call
the takeover hypercall on everybody, OPAL will re-enter the kernel
main entry point passing it a flat device-tree.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>