All these files were including module.h just for the basic EXPORT_SYMBOL infrastructure. We can shift them off to the export.h header which is a way smaller footprint and thus realize some compile time gains. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This replaces the single CPU_FTR_HVMODE_206 bit with two bits, one to indicate that we have a usable hypervisor mode, and another to indicate that the processor conforms to PowerISA version 2.06. We also add another bit to indicate that the processor conforms to ISA version 2.01 and set that for PPC970 and derivatives. Some PPC970 chips (specifically those in Apple machines) have a hypervisor mode in that MSR[HV] is always 1, but the hypervisor mode is not useful in the sense that there is no way to run any code in supervisor mode (HV=0 PR=0). On these processors, the LPES0 and LPES1 bits in HID4 are always 0, and we use that as a way of detecting that hypervisor mode is not useful. Where we have a feature section in assembly code around code that only applies on POWER7 in hypervisor mode, we use a construct like END_FTR_SECTION_IFSET(CPU_FTR_HVMODE | CPU_FTR_ARCH_206) The definition of END_FTR_SECTION_IFSET is such that the code will be enabled (not overwritten with nops) only if all bits in the provided mask are set. Note that the CPU feature check in __tlbie() only needs to check the ARCH_206 bit, not the HVMODE bit, because __tlbie() can only get called if we are running bare-metal, i.e. in hypervisor mode. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
Now that we never set a cpu above nr_cpu_ids possible we can limit our initial paca allocation to nr_cpu_ids. We can then clamp the number of cpus in platforms/iseries/setup.c. Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When running in Hypervisor mode (arch 2.06 or later), we store the PACA in HSPRG0 instead of SPRG1. The architecture specifies that SPRGs may be lost during a "nap" power management operation (though they aren't currently on POWER7) and this enables use of SPRG1 by KVM guests. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Without this, "holes" in the CPU numbering can cause us to free too many PACAs Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The combination of commit 8154c5d22d91cd16bd9985b0638c8957e4688d0e and 93c22703efa72c7527dbd586d1951c1f4a85fd70 Broke boot on iSeries. The problem is that iSeries very early boot code, which generates the device-tree and runs before our normal early initializations does need access the lppaca's very early, before the PACA array is initialized, and in fact even before the boot PACA has been initialized (it contains all 0's at this stage). However, the first patch above makes that code use the new llpaca_of(cpu) accessor, which itself is changed by the second patch to use the PACA array. We fix that by reverting iSeries to directly dereferencing the array. In addition, we fix all iterators in the iSeries code to always skip CPU whose number is above 63 which is the maximum size of that array and the maximum number of supported CPUs on these machines. Additionally, we make sure the boot_paca is properly initialized in our early startup code. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (71 commits) powerpc/44x: Update ppc44x_defconfig powerpc/watchdog: Make default timeout for Book-E watchdog a Kconfig option fsl_rio: Add comments for sRIO registers. powerpc/fsl-booke: Add e55xx (64-bit) smp defconfig powerpc/fsl-booke: Add p5020 DS board support powerpc/fsl-booke64: Use TLB CAMs to cover linear mapping on FSL 64-bit chips powerpc/fsl-booke: Add support for FSL Arch v1.0 MMU in setup_page_sizes powerpc/fsl-booke: Add support for FSL 64-bit e5500 core powerpc/85xx: add cache-sram support powerpc/85xx: add ngPIXIS FPGA device tree node to the P1022DS board powerpc: Fix compile error with paca code on ppc64e powerpc/fsl-booke: Add p3041 DS board support oprofile/fsl emb: Don't set MSR[PMM] until after clearing the interrupt. powerpc/fsl-booke: Add PCI device ids for P2040/P3041/P5010/P5020 QoirQ chips powerpc/mpc8xxx_gpio: Add support for 'qoriq-gpio' controllers powerpc/fsl_booke: Add support to boot from core other than 0 powerpc/p1022: Add probing for individual DMA channels powerpc/fsl_soc: Search all global-utilities nodes for rstccr powerpc: Fix invalid page flags in create TLB CAM path for PTE_64BIT powerpc/mpc83xx: Support for MPC8308 P1M board ... Fix up conflict with the generic irq_work changes in arch/powerpc/kernel/time.c
arch/powerpc/kernel/paca.c: In function 'allocate_lppacas': arch/powerpc/kernel/paca.c:111:1: error: parameter name omitted arch/powerpc/kernel/paca.c:111:1: error: parameter name omitted Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This arranges for the lppaca structs for most cpus to be dynamically allocated in the same manner as the paca structs. If we don't include support for legacy iSeries, only the first lppaca is statically allocated; the rest are dynamically allocated. If we include legacy iSeries support, then we statically allocate the first 64 lppaca structs, since the iSeries hypervisor requires that the lppaca structs be present in the data section of the kernel image, but legacy iSeries supports at most 64 cpus. With CONFIG_NR_CPUS, the kernel image size for a typical pSeries config went from: text data bss dec hex filename 9524478 4734564 8469944 22728986 15ad11a ../test-1024/vmlinux to: text data bss dec hex filename 9524482 3751508 8469944 21745934 14bd10e ../test-1024/vmlinux a reduction of 983052 bytes overall. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Conflicts: arch/x86/kernel/trampoline.c mm/memblock.c Merge reason: Resolve the conflicts, update to latest upstream. Signed-off-by: Ingo Molnar <mingo@elte.hu>