linux-toradex.git/arch/powerpc/kernel, branch v3.10.66

powerpc: 32 bit getcpu VDSO function uses 64 bit instructions

2014-12-16T17:09:43+00:00

commit 152d44a853e42952f6c8a504fb1f8eefd21fd5fd upstream.

I used some 64 bit instructions when adding the 32 bit getcpu VDSO
function. Fix it.

Fixes: 18ad51dd342a ("powerpc: Add VDSO version of getcpu")
Signed-off-by: Anton Blanchard 
Signed-off-by: Michael Ellerman 
Signed-off-by: Greg Kroah-Hartman

powerpc: Add AT_HWCAP2 to indicate V.CRYPTO category support

2014-07-07T01:54:15+00:00

commit dd58a092c4202f2bd490adab7285b3ff77f8e467 upstream.

The Vector Crypto category instructions are supported by current POWER8
chips, advertise them to userspace using a specific bit to properly
differentiate with chips of the same architecture level that might not
have them.

Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Greg Kroah-Hartman

powerpc: fix typo 'CONFIG_PMAC'

2014-07-07T01:54:15+00:00

commit 6e0fdf9af216887e0032c19d276889aad41cad00 upstream.

Commit b0d278b7d3ae ("powerpc/perf_event: Reduce latency of calling
perf_event_do_pending") added a check for CONFIG_PMAC were a check for
CONFIG_PPC_PMAC was clearly intended.

Fixes: b0d278b7d3ae ("powerpc/perf_event: Reduce latency of calling perf_event_do_pending")
Signed-off-by: Paul Bolle 
Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Greg Kroah-Hartman

powerpc/tm: Fix crash when forking inside a transaction

2014-06-07T20:25:38+00:00

commit 621b5060e823301d0cba4cb52a7ee3491922d291 upstream.

When we fork/clone we currently don't copy any of the TM state to the new
thread.  This results in a TM bad thing (program check) when the new process is
switched in as the kernel does a tmrechkpt with TEXASR FS not set.  Also, since
R1 is from userspace, we trigger the bad kernel stack pointer detection.  So we
end up with something like this:

   Bad kernel stack pointer 0 at c0000000000404fc
   cpu 0x2: Vector: 700 (Program Check) at [c00000003ffefd40]
       pc: c0000000000404fc: restore_gprs+0xc0/0x148
       lr: 0000000000000000
       sp: 0
      msr: 9000000100201030
     current = 0xc000001dd1417c30
     paca    = 0xc00000000fe00800   softe: 0        irq_happened: 0x01
       pid   = 0, comm = swapper/2
   WARNING: exception is not recoverable, can't continue

The below fixes this by flushing the TM state before we copy the task_struct to
the clone.  To do this we go through the tmreclaim patch, which removes the
checkpointed registers from the CPU and transitions the CPU out of TM suspend
mode.  Hence we need to call tmrechkpt after to restore the checkpointed state
and the TM mode for the current task.

To make this fail from userspace is simply:
	tbegin
	li	r0, 2
	sc
	

Kudos to Adhemerval Zanella Neto for finding this.

Signed-off-by: Michael Neuling 
cc: Adhemerval Zanella Neto 
Signed-off-by: Benjamin Herrenschmidt 
[Backported to 3.10: context adjust]
Signed-off-by: Xue Liu 
Signed-off-by: Greg Kroah-Hartman

powerpc/tm: Disable IRQ in tm_recheckpoint

2014-05-13T11:59:42+00:00

commit e6b8fd028b584ffca7a7255b8971f254932c9fce upstream.

We can't take an IRQ when we're about to do a trechkpt as our GPR state is set
to user GPR values.

We've hit this when running some IBM Java stress tests in the lab resulting in
the following dump:

  cpu 0x3f: Vector: 700 (Program Check) at [c000000007eb3d40]
      pc: c000000000050074: restore_gprs+0xc0/0x148
      lr: 00000000b52a8184
      sp: ac57d360
     msr: 8000000100201030
    current = 0xc00000002c500000
    paca    = 0xc000000007dbfc00     softe: 0     irq_happened: 0x00
      pid   = 34535, comm = Pooled Thread #
  R00 = 00000000b52a8184   R16 = 00000000b3e48fda
  R01 = 00000000ac57d360   R17 = 00000000ade79bd8
  R02 = 00000000ac586930   R18 = 000000000fac9bcc
  R03 = 00000000ade60000   R19 = 00000000ac57f930
  R04 = 00000000f6624918   R20 = 00000000ade79be8
  R05 = 00000000f663f238   R21 = 00000000ac218a54
  R06 = 0000000000000002   R22 = 000000000f956280
  R07 = 0000000000000008   R23 = 000000000000007e
  R08 = 000000000000000a   R24 = 000000000000000c
  R09 = 00000000b6e69160   R25 = 00000000b424cf00
  R10 = 0000000000000181   R26 = 00000000f66256d4
  R11 = 000000000f365ec0   R27 = 00000000b6fdcdd0
  R12 = 00000000f66400f0   R28 = 0000000000000001
  R13 = 00000000ada71900   R29 = 00000000ade5a300
  R14 = 00000000ac2185a8   R30 = 00000000f663f238
  R15 = 0000000000000004   R31 = 00000000f6624918
  pc  = c000000000050074 restore_gprs+0xc0/0x148
  cfar= c00000000004fe28 dont_restore_vec+0x1c/0x1a4
  lr  = 00000000b52a8184
  msr = 8000000100201030   cr  = 24804888
  ctr = 0000000000000000   xer = 0000000000000000   trap =  700

This moves tm_recheckpoint to a C function and moves the tm_restore_sprs into
that function.  It then adds IRQ disabling over the trechkpt critical section.
It also sets the TEXASR FS in the signals code to ensure this is never set now
that we explictly write the TM sprs in tm_recheckpoint.

Signed-off-by: Michael Neuling 
Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Greg Kroah-Hartman

powerpc: Align p_dyn, p_rela and p_st symbols

2014-03-24T04:38:14+00:00

commit a5b2cf5b1af424ee3dd9e3ce6d5cea18cb927e67 upstream.

The 64bit relocation code places a few symbols in the text segment.
These symbols are only 4 byte aligned where they need to be 8 byte
aligned. Add an explicit alignment.

Signed-off-by: Anton Blanchard 
Tested-by: Laurent Dufour 
Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Greg Kroah-Hartman

powerpc/crashdump : Fix page frame number check in copy_oldmem_page

2014-03-07T05:30:08+00:00

commit f5295bd8ea8a65dc5eac608b151386314cb978f1 upstream.

In copy_oldmem_page, the current check using max_pfn and min_low_pfn to
decide if the page is backed or not, is not valid when the memory layout is
not continuous.

This happens when running as a QEMU/KVM guest, where RTAS is mapped higher
in the memory. In that case max_pfn points to the end of RTAS, and a hole
between the end of the kdump kernel and RTAS is not backed by PTEs. As a
consequence, the kdump kernel is crashing in copy_oldmem_page when accessing
in a direct way the pages in that hole.

This fix relies on the memblock's service memblock_is_region_memory to
check if the read page is part or not of the directly accessible memory.

Signed-off-by: Laurent Dufour 
Tested-by: Mahesh Salgaonkar 
Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Greg Kroah-Hartman

powerpc: Make sure "cache" directory is removed when offlining cpu

2014-02-06T19:08:18+00:00

commit 91b973f90c1220d71923e7efe1e61f5329806380 upstream.

The code in remove_cache_dir() is supposed to remove the "cache"
subdirectory from the sysfs directory for a CPU when that CPU is
being offlined.  It tries to do this by calling kobject_put() on
the kobject for the subdirectory.  However, the subdirectory only
gets removed once the last reference goes away, and the reference
being put here may well not be the last reference.  That means
that the "cache" subdirectory may still exist when the offlining
operation has finished.  If the same CPU subsequently gets onlined,
the code tries to add a new "cache" subdirectory.  If the old
subdirectory has not yet been removed, we get a WARN_ON in the
sysfs code, with stack trace, and an error message printed on the
console.  Further, we ultimately end up with an online cpu with no
"cache" subdirectory.

This fixes it by doing an explicit kobject_del() at the point where
we want the subdirectory to go away.  kobject_del() removes the sysfs
directory even though the object still exists in memory.  The object
will get freed at some point in the future.  A subsequent onlining
operation can create a new sysfs directory, even if the old object
still exists in memory, without causing any problems.

Signed-off-by: Paul Mackerras 
Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Greg Kroah-Hartman

powerpc: Align p_end

2014-01-09T20:24:22+00:00

commit 286e4f90a72c0b0621dde0294af6ed4b0baddabb upstream.

p_end is an 8 byte value embedded in the text section. This means it
is only 4 byte aligned when it should be 8 byte aligned. Fix this
by adding an explicit alignment.

This fixes an issue where POWER7 little endian builds with
CONFIG_RELOCATABLE=y fail to boot.

Signed-off-by: Anton Blanchard 
Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Greg Kroah-Hartman

powerpc/signals: Improved mark VSX not saved with small contexts fix

2013-12-04T18:57:16+00:00

commit ec67ad82814bee92251fd963bf01c7a173856555 upstream.

In a recent patch:
  commit c13f20ac48328b05cd3b8c19e31ed6c132b44b42
  Author: Michael Neuling 
  powerpc/signals: Mark VSX not saved with small contexts

We fixed an issue but an improved solution was later discussed after the patch
was merged.

Firstly, this patch doesn't handle the 64bit signals case, which could also hit
this issue (but has never been reported).

Secondly, the original patch isn't clear what MSR VSX should be set to.  The
new approach below always clears the MSR VSX bit (to indicate no VSX is in the
context) and sets it only in the specific case where VSX is available (ie. when
VSX has been used and the signal context passed has space to provide the
state).

This reverts the original patch and replaces it with the improved solution.  It
also adds a 64 bit version.

Signed-off-by: Michael Neuling 
Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Greg Kroah-Hartman