linux-toradex.git/arch/sh/kernel/cpu/sh3/Makefile, branch v4.2.7

sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB

2013-03-20T13:48:15+00:00

SH GPIO drivers all use gpiolib and CONFIG_GENERIC_GPIO is only selected
through CONFIG_GPIOLIB, yet some compilation units depended on
CONFIG_GENERIC_GPIO. Make them depend on CONFIG_GPIOLIB instead since it
is more accurate and prepares us for the future removal of
CONFIG_GENERIC_GPIO.

Signed-off-by: Alexandre Courbot 
Acked-by: Paul Mundt 
Acked-by: Arnd Bergmann 
Acked-by: Linus Walleij

serial: sh-sci: Abstract register maps.

2011-06-14T03:40:19+00:00

This takes a bit of a sledgehammer to the horribly CPU subtype
ifdef-ridden header and abstracts all of the different register layouts
in to distinct types which in turn can be overriden on a per-port basis,
or permitted to default to the map matching the port type at probe time.

In the process this ultimately fixes up inumerable bugs with mismatches
on various CPU types (particularly the legacy ones that were obviously
broken years ago and no one noticed) and provides a more tightly coupled
and consolidated platform for extending and implementing generic
features.

Signed-off-by: Paul Mundt

sh: hibernation support

2009-03-10T03:55:40+00:00

Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.

To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.

The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.

Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.

Signed-off-by: Magnus Damm 
Signed-off-by: Paul Mundt

sh: Add sh7720 pinmux code

2008-10-20T01:34:25+00:00

This patch adds pinmux and gpio support for the sh7720 processor.

Signed-off-by: Magnus Damm 
Signed-off-by: Paul Mundt

sh: unify external irq pin code for sh3

2008-05-08T10:52:00+00:00

This patch unifies the sh3 external irq pin code. It buys us some
savings with reduced code redundancy, but the main feature with
this change is irq sense selection support for all sh3 processors.

Signed-off-by: Magnus Damm 
Signed-off-by: Paul Mundt

sh: sh7712 clock support

2008-01-28T04:19:02+00:00

This patch provides specific clock support for the SH7712.

Signed-off-by: Andrew Murray 
Signed-off-by: Paul Mundt

sh: Add support for SH7721 CPU subtype.

2008-01-28T04:19:02+00:00

Signed-off-by: Yoshihiro Shimoda 
Signed-off-by: Paul Mundt

sh: Add SH7720 CPU support.

2007-09-21T02:57:49+00:00

This adds support for the SH7720 (SH3-DSP) CPU.

Signed-off by: Markus Brunner 
Signed-off by: Mark Jonas 
Signed-off-by: Paul Mundt

sh: intc - add support for SH7706, SH7707, SH7708, SH7709

2007-09-21T02:57:46+00:00

This patch unifies the cpu specific interrupt setup code for
sh7706, sh7707, sh7708 and sh7709 and moves the code into a new
file called setup-sh770x.c.  It makes sense to share the setup code
between these processors because most hardware blocks are identical
from a software point of view. With this patch the sh770x processors
now have a complete set of vectors that match with the information
provided by the data sheets. This is a big improvement for sh7708.

Vectors for IRQ4 and IRQ5 are enabled by default. Use
plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.

This patch also unifies the platform device setup code which means
that the rtc driver now has platform data for all sh770x processors.

Signed-off-by: Magnus Damm 
Signed-off-by: Paul Mundt

sh: remove support for sh7300 and solution engine 7300

2007-07-26T06:37:57+00:00

This patch removes old dead code:
- kill off sh7300 cpu support
- get rid of broken solution engine 7300 board support

Signed-off-by: Magnus Damm 
Signed-off-by: Paul Mundt