linux-toradex.git/arch/sh/kernel/cpu/sh4a, branch v3.13.8

sh: delete __cpuinit usage from all sh files

2013-07-14T23:36:53+00:00

The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications.  For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.

After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out.  Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.

Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit  -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings.  In any case, they are temporary and harmless.

This removes all the arch/sh uses of the __cpuinit macros from
all C files.  Currently sh does not have any __CPUINIT used in
assembly files.

[1] https://lkml.org/lkml/2013/5/20/589

Cc: Paul Mundt 
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Gortmaker

sh_eth: get SH7724 support out of #ifdef

2013-06-08T06:38:24+00:00

Get the SH7724 code/data in the driver out of #ifdef by adding "r8a7724-ether"
to the platform driver's ID table. Change the Ether platform device's name in
the SH platform code accordingly.

Signed-off-by: Sergei Shtylyov 
Signed-off-by: David S. Miller

sh_eth: get SH77{34|63} support out of #ifdef

2013-06-08T06:38:24+00:00

Get the SH77{34|63} specific code/data in the driver out of #ifdef by adding
"sh7734-gether" and "sh7763-gether" to the platform driver's ID table.  Note
that we have to split the 'struct sh_eth_cpu_data' instance into two due to
#ifdef inside it; note that we can kill the duplicate sh_eth_set_rate_gether().
Change the GEther platform device's name in the SH platform code accordingly.

Signed-off-by: Sergei Shtylyov 
Signed-off-by: David S. Miller

Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux

2013-05-09T16:59:16+00:00

Pull removal of GENERIC_GPIO from Grant Likely:
 "GENERIC_GPIO now synonymous with GPIOLIB.  There are no longer any
  valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
  is possible to do so which has been causing confusion and breakage.
  This branch does the work to completely eliminate GENERIC_GPIO."

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
  gpio: update gpio Chinese documentation
  Remove GENERIC_GPIO config option
  Convert selectors of GENERIC_GPIO to GPIOLIB
  blackfin: force use of gpiolib
  m68k: coldfire: use gpiolib
  mips: pnx833x: remove requirement for GENERIC_GPIO
  openrisc: default GENERIC_GPIO to false
  avr32: default GENERIC_GPIO to false
  xtensa: remove explicit selection of GENERIC_GPIO
  sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
  powerpc: remove redundant GENERIC_GPIO selection
  unicore32: default GENERIC_GPIO to false
  unicore32: remove unneeded select GENERIC_GPIO
  arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
  arm: remove redundant GENERIC_GPIO selection
  mips: alchemy: require gpiolib
  mips: txx9: change GENERIC_GPIO to GPIOLIB
  mips: loongson: use GPIO driver on CONFIG_GPIOLIB
  mips: remove redundant GENERIC_GPIO select

sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB

2013-03-20T13:48:15+00:00

SH GPIO drivers all use gpiolib and CONFIG_GENERIC_GPIO is only selected
through CONFIG_GPIOLIB, yet some compilation units depended on
CONFIG_GENERIC_GPIO. Make them depend on CONFIG_GPIOLIB instead since it
is more accurate and prepares us for the future removal of
CONFIG_GENERIC_GPIO.

Signed-off-by: Alexandre Courbot 
Acked-by: Paul Mundt 
Acked-by: Arnd Bergmann 
Acked-by: Linus Walleij

sh: shx3: Add pin control resources

2013-03-15T12:33:52+00:00

Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.

The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.

Signed-off-by: Laurent Pinchart

sh: sh7786: Add pin control resources

2013-03-15T12:33:52+00:00

Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.

The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.

Signed-off-by: Laurent Pinchart

sh: sh7785: Add pin control resources

2013-03-15T12:33:52+00:00

Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.

The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.

Signed-off-by: Laurent Pinchart

sh: sh7757: Add pin control resources

2013-03-15T12:33:52+00:00

Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.

The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.

Signed-off-by: Laurent Pinchart

sh: sh7724: Add pin control resources

2013-03-15T12:33:51+00:00

Add memory resources for the pin control platform device to let the
sh-pfc driver ioremap() registers properly instead of evily casting
register physical addresses to virtual addresses.

The memory resource address range has been extracted from the config and
data registes lists in the sh-pfc driver.

Signed-off-by: Laurent Pinchart