commit fd7c99142d77dc4a851879a66715abf12a3193fb upstream.

Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.

Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e658a6f14d7c0243205f035979d0ecf6c12a036f upstream.

For large values of "mult" and long uptimes, the intermediate
result of "cycles * mult" can overflow 64 bits.  For example,
the tile platform calls clocksource_cyc2ns with a 1.2 GHz clock;
we have mult = 853, and after 208.5 days, we overflow 64 bits.

Since clocksource_cyc2ns() is intended to be used for relative
cycle counts, not absolute cycle counts, performance is more
importance than accepting a wider range of cycle values.  So,
just use mult_frac() directly in tile's sched_clock().

Commit 4cecf6d401a0 ("sched, x86: Avoid unnecessary overflow
in sched_clock") by Salman Qazi results in essentially the same
generated code for x86 as this change does for tile.  In fact,
a follow-on change by Salman introduced mult_frac() and switched
to using it, so the C code was largely identical at that point too.

Peter Zijlstra then added mul_u64_u32_shr() and switched x86
to use it.  This is, in principle, better; by optimizing the
64x64->64 multiplies to be 32x32->64 multiplies we can potentially
save some time.  However, the compiler piplines the 64x64->64
multiplies pretty well, and the conditional branch in the generic
mul_u64_u32_shr() causes some bubbles in execution, with the
result that it's pretty much a wash.  If tilegx provided its own
implementation of mul_u64_u32_shr() without the conditional branch,
we could potentially save 3 cycles, but that seems like small gain
for a fair amount of additional build scaffolding; no other platform
currently provides a mul_u64_u32_shr() override, and tile doesn't
currently have an <asm/div64.h> header to put the override in.

Additionally, gcc currently has an optimization bug that prevents
it from recognizing the opportunity to use a 32x32->64 multiply,
and so the result would be no better than the existing mult_frac()
until such time as the compiler is fixed.

For now, just using mult_frac() seems like the right answer.

Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There were still a number of references to my old Red Hat email
address in the kernel source. Remove these while keeping the
Red Hat copyright notices intact.

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull arch/tile bugfix from Chris Metcalf:
 "This fixes a bug in 'make allmodconfig'"

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tile: fix build failure

When building with allmodconfig the build was failing with the error:

arch/tile/kernel/usb.c:70:1: warning: data definition has no type or storage class [enabled by default]
arch/tile/kernel/usb.c:70:1: error: type defaults to 'int' in declaration of 'arch_initcall' [-Werror=implicit-int]
arch/tile/kernel/usb.c:70:1: warning: parameter names (without types) in function declaration [enabled by default]
arch/tile/kernel/usb.c:63:19: warning: 'tilegx_usb_init' defined but not used [-Wunused-function]

Include linux/module.h to resolve the build failure.

Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>

Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.

Remove the argument.

Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>

Pull tile updates from Chris Metcalf:
 "This includes secure computing support as well as miscellaneous minor
  improvements"

* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tile: correct some typos in opcode type names
  tile/vdso: emit a GNU hash as well
  tile: Remove finish_arch_switch
  tile: enable full SECCOMP support
  tile/time: Migrate to new 'set-state' interface

Pull irq updates from Thomas Gleixner:
 "This updated pull request does not contain the last few GIC related
  patches which were reported to cause a regression.  There is a fix
  available, but I let it breed for a couple of days first.

  The irq departement provides:

   - new infrastructure to support non PCI based MSI interrupts
   - a couple of new irq chip drivers
   - the usual pile of fixlets and updates to irq chip drivers
   - preparatory changes for removal of the irq argument from interrupt
     flow handlers
   - preparatory changes to remove IRQF_VALID"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
  irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
  irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
  irqchip: Add documentation for the bcm2836 interrupt controller
  irqchip/bcm2835: Add support for being used as a second level controller
  irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
  PCI: xilinx: Fix typo in function name
  irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
  irqchip/gic: Only allow the primary GIC to set the CPU map
  PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
  unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
  tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
  m68k/irq: Prepare irq handlers for irq argument removal
  C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
  blackfin: Prepare irq handlers for irq argument removal
  arc/irq: Prepare idu_cascade_isr for irq argument removal
  sparc/irq: Use access helper irq_data_get_affinity_mask()
  sparc/irq: Use helper irq_data_get_irq_handler_data()
  parisc/irq: Use access helper irq_data_get_affinity_mask()
  mn10300/irq: Use access helper irq_data_get_affinity_mask()
  irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
  ...

Pull scheduler updates from Ingo Molnar:
 "The biggest change in this cycle is the rewrite of the main SMP load
  balancing metric: the CPU load/utilization.  The main goal was to make
  the metric more precise and more representative - see the changelog of
  this commit for the gory details:

    9d89c257dfb9 ("sched/fair: Rewrite runnable load and utilization average tracking")

  It is done in a way that significantly reduces complexity of the code:

    5 files changed, 249 insertions(+), 494 deletions(-)

  and the performance testing results are encouraging.  Nevertheless we
  need to keep an eye on potential regressions, since this potentially
  affects every SMP workload in existence.

  This work comes from Yuyang Du.

  Other changes:

   - SCHED_DL updates.  (Andrea Parri)

   - Simplify architecture callbacks by removing finish_arch_switch().
     (Peter Zijlstra et al)

   - cputime accounting: guarantee stime + utime == rtime.  (Peter
     Zijlstra)

   - optimize idle CPU wakeups some more - inspired by Facebook server
     loads.  (Mike Galbraith)

   - stop_machine fixes and updates.  (Oleg Nesterov)

   - Introduce the 'trace_sched_waking' tracepoint.  (Peter Zijlstra)

   - sched/numa tweaks.  (Srikar Dronamraju)

   - misc fixes and small cleanups"

* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
  sched/deadline: Fix comment in enqueue_task_dl()
  sched/deadline: Fix comment in push_dl_tasks()
  sched: Change the sched_class::set_cpus_allowed() calling context
  sched: Make sched_class::set_cpus_allowed() unconditional
  sched: Fix a race between __kthread_bind() and sched_setaffinity()
  sched: Ensure a task has a non-normalized vruntime when returning back to CFS
  sched/numa: Fix NUMA_DIRECT topology identification
  tile: Reorganize _switch_to()
  sched, sparc32: Update scheduler comments in copy_thread()
  sched: Remove finish_arch_switch()
  sched, tile: Remove finish_arch_switch
  sched, sh: Fold finish_arch_switch() into switch_to()
  sched, score: Remove finish_arch_switch()
  sched, avr32: Remove finish_arch_switch()
  sched, MIPS: Get rid of finish_arch_switch()
  sched, arm: Remove finish_arch_switch()
  sched/fair: Clean up load average references
  sched/fair: Provide runnable_load_avg back to cfs_rq
  sched/fair: Remove task and group entity load when they are dead
  sched/fair: Init cfs_rq's sched_entity load average
  ...

Pull driver core updates from Greg KH:
 "Here is the new patches for the driver core / sysfs for 4.3-rc1.

  Very small number of changes here, all the details are in the
  shortlog, nothing major happening at all this kernel release, which is
  nice to see"

* tag 'driver-core-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  bus: subsys: update return type of ->remove_dev() to void
  driver core: correct device's shutdown order
  driver core: fix docbook for device_private.device
  selftests: firmware: skip timeout checks for kernels without user mode helper
  kernel, cpu: Remove bogus __ref annotations
  cpu: Remove bogus __ref annotation of cpu_subsys_online()
  firmware: fix wrong memory deallocation in fw_add_devm_name()
  sysfs.txt: update show method notes about sprintf/snprintf/scnprintf usage
  devres: fix devres_get()