Pull ARM SoC driver changes from Olof Johansson:
 "This is a rather large set of patches for device drivers that for one
  reason or another the subsystem maintainer preferred to get merged
  through the arm-soc tree.  There are both new drivers as well as
  existing drivers that are getting converted from platform-specific
  code into standalone drivers using the appropriate subsystem specific
  interfaces.

  In particular, we can now have pinctrl, clk, clksource and irqchip
  drivers in one file per driver, without the need to call into platform
  specific interface, or to get called from platform specific code, as
  long as all information about the hardware is provided through a
  device tree.

  Most of the drivers we touch this time are for clocksource.  Since now
  most of them are part of drivers/clocksource, I expect that we won't
  have to touch these again from arm-soc and can let the clocksource
  maintainers take care of these in the future.

  Another larger part of this series is specific to the exynos platform,
  which is seeing some significant effort in upstreaming and
  modernization of its device drivers this time around, which
  unfortunately is also the cause for the churn and a lot of the merge
  conflicts.

  There is one new subsystem that gets merged as part of this series:
  the reset controller interface, which is a very simple interface for
  taking devices on the SoC out of reset or back into reset.  Patches to
  use this interface on i.MX follow later in this merge window, and we
  are going to have other platforms (at least tegra and sirf) get
  converted in 3.11.  This will let us get rid of platform specific
  callbacks in a number of platform independent device drivers."

* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
  irqchip: s3c24xx: add missing __init annotations
  ARM: dts: Disable the RTC by default on exynos5
  clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
  ARM: exynos: restore mach/regs-clock.h for exynos5
  clocksource: exynos_mct: fix build error on non-DT
  pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
  irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
  reset: NULL deref on allocation failure
  reset: Add reset controller API
  dt: describe base reset signal binding
  ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
  ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
  ARM: EXYNOS: Enable PMUs for exynos4
  irqchip: exynos-combiner: Correct combined IRQs for exynos4
  irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
  ARM: EXYNOS: fix compilation error introduced due to common clock migration
  clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
  clk: exynos4: export clocks required for fimc-is
  clk: samsung: Fix compilation error
  clk: tegra: fix enum tegra114_clk to match binding
  ...

Make virtualization drivers be logically grouped together (physically
near each other) in the kconfig menu by moving "Virtualization drivers"
to be near "Virtio drivers", Microsort Hyper-V, and Xen driver support.

This is just a user-friendly, visual search change.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This adds a simple API for devices to request being reset
by separate reset controller hardware and implements the
reset signal device tree binding.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Pavel Machek <pavel@ucw.cz>

SSBI is the Qualcomm single-wire serial bus interface used to connect
the MSM devices to the PMIC and other devices.

Since SSBI only supports a single slave, the driver gets the name of the
slave device passed in from the board file through the master device's
platform data.

SSBI registers pretty early (postcore), so that the PMIC can come up
before the board init. This is useful if the board init requires the
use of gpios that are connected through the PMIC.

Based on a patch by Dima Zavin <dima@android.com> that can be found at:
http://android.git.kernel.org/?p=kernel/msm.git;a=commitdiff;h=eb060bac4

This patch adds PMIC Arbiter support for the MSM8660. The PMIC Arbiter
is a hardware wrapper around the SSBI 2.0 controller that is designed to
overcome concurrency issues and security limitations.  A controller_type
field is added to the platform data to specify the type of the SSBI
controller (1.0, 2.0, or PMIC Arbiter).

[davidb@codeaurora.org:
 I've moved this driver into drivers/ssbi/ and added an include for
 linux/module.h so that it will compile]

Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull char/misc driver patches from Greg Kroah-Hartman:
 "Here's the big char/misc driver patches for 3.9-rc1.

  Nothing major here, just lots of different driver updates (mei,
  hyperv, ipack, extcon, vmci, etc.).

  All of these have been in the linux-next tree for a while."

* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
  w1: w1_therm: Add force-pullup option for "broken" sensors
  w1: ds2482: Added 1-Wire pull-up support to the driver
  vme: add missing put_device() after device_register() fails
  extcon: max8997: Use workqueue to check cable state after completing boot of platform
  extcon: max8997: Set default UART/USB path on probe
  extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
  extcon: max8997: Set default of ADC debounce time during initialization
  extcon: max8997: Remove duplicate code related to set H/W line path
  extcon: max8997: Move defined constant to header file
  extcon: max77693: Make max77693_extcon_cable static
  extcon: max8997: Remove unreachable code
  extcon: max8997: Make max8997_extcon_cable static
  extcon: max77693: Remove unnecessary goto statement to improve readability
  extcon: max77693: Convert to devm_input_allocate_device()
  extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
  CREDITS: update email and address of Harald Hoyer
  extcon: arizona: Use MICDET for final microphone identification
  extcon: arizona: Always take the first HPDET reading as the final one
  extcon: arizona: Clear _trig_sts bits after jack detection
  extcon: arizona: Don't HPDET magic when headphones are enabled
  ...

The pl320 IPC allows for interprocessor communication between the
highbank A9 and the EnergyCore Management Engine. The pl320 implements
a straightforward mailbox protocol.

Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

A PCI-Express non-transparent bridge (NTB) is a point-to-point PCIe bus
connecting 2 systems, providing electrical isolation between the two subsystems.
A non-transparent bridge is functionally similar to a transparent bridge except
that both sides of the bridge have their own independent address domains.  The
host on one side of the bridge will not have the visibility of the complete
memory or I/O space on the other side of the bridge.  To communicate across the
non-transparent bridge, each NTB endpoint has one (or more) apertures exposed to
the local system.  Writes to these apertures are mirrored to memory on the
remote system.  Communications can also occur through the use of doorbell
registers that initiate interrupts to the alternate domain, and scratch-pad
registers accessible from both sides.

The NTB device driver is needed to configure these memory windows, doorbell, and
scratch-pad registers as well as use them in such a way as they can be turned
into a viable communication channel to the remote system.  ntb_hw.[ch]
determines the usage model (NTB to NTB or NTB to Root Port) and abstracts away
the underlying hardware to provide access and a common interface to the doorbell
registers, scratch pads, and memory windows.  These hardware interfaces are
exported so that other, non-mainlined kernel drivers can access these.
ntb_transport.[ch] also uses the exported interfaces in ntb_hw.[ch] to setup a
communication channel(s) and provide a reliable way of transferring data from
one side to the other, which it then exports so that "client" drivers can access
them.  These client drivers are used to provide a standard kernel interface
(i.e., Ethernet device) to NTB, such that Linux can transfer data from one
system to the other in a standard way.

Signed-off-by: Jon Mason <jon.mason@intel.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The ipack subsystem is cleaned up enough to now move out of the staging
tree, and into drivers/ipack.

Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ARM soc driver specific changes from Olof Johansson:
 - A long-coming conversion of various platforms to a common LED
   infrastructure
 - AT91 is moved over to use the newer MCI driver for MMC
 - Pincontrol conversions for samsung platforms
 - DT bindings for gscaler on samsung
 - i2c driver fixes for tegra, acked by i2c maintainer

Fix up conflicts as per Olof.

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  drivers: bus: omap_l3: use resources instead of hardcoded irqs
  pinctrl: exynos: Fix wakeup IRQ domain registration check
  pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
  pinctrl: exynos: Correct the detection of wakeup-eint node
  pinctrl: exynos: Mark exynos_irq_demux_eint as inline
  pinctrl: exynos: Handle only unmasked wakeup interrupts
  pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
  pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
  drivers: bus: Move the OMAP interconnect driver to drivers/bus/
  i2c: tegra: dynamically control fast clk
  i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
  ARM: tegra: clock: remove unused clock entry for i2c
  ARM: tegra: clock: add connection name in i2c clock entry
  i2c: tegra: pass proper name for getting clock
  ARM: tegra: clock: add i2c fast clock entry in clock table
  ARM: EXYNOS: Adds G-Scaler device from Device Tree
  ARM: EXYNOS: Add clock support for G-Scaler
  ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
  ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
  ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
  ...

The BCM2835 contains a custom interrupt controller, which supports 72
interrupt sources using a 2-level register scheme. The interrupt
controller, or the HW block containing it, is referred to occasionally
as "armctrl" in the SoC documentation, hence the symbol naming in the
code.

This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:

* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
* Moved implementation to drivers/irchip/.
* Added devicetree documentation, and hence removed list of IRQs from
  bcm2835.dtsi.
* Changed shift in MAKE_HWIRQ() and HWIRQ_BANK() from 8 to 5 to reduce
  the size of the hwirq space, and pass the total size of the hwirq space
  to irq_domain_add_linear(), rather than just the number of valid hwirqs;
  the two are different due to the hwirq space being sparse.
* Added the interrupt controller DT node to the top-level of the DT,
  rather than nesting it inside a /axi node. Hence, changed the reg value
  since /axi had a ranges property. This seems simpler to me, but I'm not
  sure if everyone will like this change or not.
* Don't set struct irq_domain_ops.map = irq_domain_simple_map, hence
  removing the need to patch include/linux/irqdomain.h or
  kernel/irq/irqdomain.c.
* Simplified armctrl_of_init() using of_iomap().
* Removed unused IS_VALID_BANK()/IS_VALID_IRQ() macros.
* Renamed armctrl_handle_irq() to prevent possible symbol clashes.
* Made armctrl_of_init() static.
* Removed comment "Each bank is registered as a separate interrupt
  controller" since this is no longer true.
* Removed FSF address from license header.
* Added my name to copyright header.

Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>