Drivers that needs acpi_device_fix_up_power(), allow them to be built as
modules by exporting this function.

Cc: <stable@vger.kernel.org> # 4.5+
Tested-by: Laszlo Fiat <laszlo.fiat@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Adds a function that sets the pointer to dev_pm_domain in struct device
and that warns if the device has already finished probing. The reason
why we want to enforce that is because in the general case that can
cause problems and also that we can simplify code quite a bit if we can
always assume that.

This patch also changes all current code that directly sets the
dev.pm_domain pointer.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

There is a concern that if the platform firmware was involved in
the system resume that's being completed,  some devices might have
been reset by it and if those devices had the power.direct_complete
flag set during the preceding suspend transition, they may stay
in a reset-power-on state indefinitely (until they are runtime-resumed
and then suspended again).  That may not be a big deal from the
individual device's perspective, but if the system is an SoC, it may
be prevented from entering deep SoC-wide low-power states on idle
because of that.

The devices that are most likely to be affected by this issue are
PCI devices and ACPI-enumerated devices using the general ACPI PM
domain, so to prevent it from happening for those devices, force a
runtime resume for them if they have their power.direct_complete
flags set and the platform firmware was involved in the resume
transition currently in progress.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

* acpi-pm:
  ACPI / bus: Move duplicate code to a separate new function
  mfd: Add support for Intel Sunrisepoint LPSS devices
  dmaengine: add a driver for Intel integrated DMA 64-bit
  mfd: make mfd_remove_devices() iterate in reverse order
  driver core: implement device_for_each_child_reverse()
  klist: implement klist_prev()
  Driver core: wakeup the parent device before trying probe
  ACPI / PM: Attach ACPI power domain only once
  PM / QoS: Make it possible to expose device latency tolerance to userspace
  ACPI / PM: Update the copyright notice and description of power.c

* acpi-scan:
  ACPI / bus: Move ACPI bus type registration
  ACPI / scan: Move bus operations and notification routines to bus.c
  ACPI / scan: Move device matching code to bus.c
  ACPI / scan: Move sysfs-related device code to a separate file

* acpi-processor:
  PCC: Disable compilation by default
  ACPI: Decouple ACPI idle and ACPI processor drivers
  ACPI: Split out ACPI PSS from ACPI Processor driver
  PCC: Initialize PCC Mailbox earlier at boot
  ACPI / processor: remove leftover __refdata annotations

* acpi-assorted:
  ACPI: fix acpi_debugfs_init prototype
  ACPI: Remove FSF mailing addresses

Commit 20dacb71ad28 ("ACPI / PM: Rework device power management to follow
ACPI 6") changed the device power management to use D3hot if the device
in question does not have _PR3 method even if D3cold was requested by the
caller.

However, if the device has _PR3 device->power.state is also set to D3hot
instead of D3Cold after power resources have been turned off because
device->power.state will be assigned from "state" instead of
"target_state".

Next time the device is transitioned to D0, acpi_power_transition() will
find that the current power state of the device is D3hot instead of D3cold
which causes it to power down all resources required for the current
(wrong) state D3hot.

Below is a simplified ASL example of a real touch panel device which
triggers the problem:

  Scope (TPL1)
  {
      Name (_PR0, Package (1) { \_SB.PCI0.I2C1.PXTC })
      Name (_PR3, Package (1) { \_SB.PCI0.I2C1.PXTC })
      ...
  }

In both D0 and D3hot the same power resource is required. However, when
acpi_power_transition() turns off power resources required for D3hot (as
the device is transitioned to D0) it powers down PXTC which then makes the
device to lose its power.

Fix this by assigning "target_state" to the device power state instead of
"state" that is always D3hot even for devices with valid _PR3.

Fixes: 20dacb71ad28 (ACPI / PM: Rework device power management to follow ACPI 6)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Some devices, like MFD subdevices, share a single ACPI companion device so
that they are able to access their resources and children. However,
currently all these subdevices are attached to the ACPI power domain and
this might cause that the power methods for the companion device get called
more than once.

In order to solve this we attach the ACPI power domain only to the first
physical device that is bound to the ACPI companion device. In case of MFD
devices, this is the parent MFD device itself.

Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

There is no need to carry potentially outdated Free Software Foundation
mailing address in file headers since the COPYING file includes it.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Add missing invocation of pm_generic_complete() to
acpi_subsys_complete() to allow ->complete callbacks provided
by the drivers of devices using the ACPI PM domain to be executed
during system resume.

Fixes: f25c0ae2b4c4 (ACPI / PM: Avoid resuming devices in ACPI PM domain during system suspend)
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>