linux-toradex.git/drivers/ata/Makefile, branch v2.6.38.6

[libata] new driver acard_ahci, for ATP8620 host controller

2011-01-06T00:43:22+00:00

Add support for Acard ATP8620 host controller.

Based upon initial version by Jeff Garzik.

Signed-off-by: David Milburn 
Signed-off-by: Jeff Garzik

pata_mpc52xx: driver needs BMDMA

2010-12-24T18:33:37+00:00

Found by this build-error if BMDMA is disabled:

drivers/ata/pata_mpc52xx.c: In function 'mpc52xx_ata_init_one':
drivers/ata/pata_mpc52xx.c:662: error: 'ata_bmdma_interrupt' undeclared (first use in this function)
...

Move the Kconfig entry to the proper location as needed since
9a7780c9acb821fe1c2b6fc53f74cc2556ff5364 (libata-sff: make BMDMA optional)

Signed-off-by: Wolfram Sang 
Signed-off-by: Jeff Garzik

Drivers: ata: Makefile: replace the use of -objs with -y

2010-10-22T01:17:32+00:00

Changed -objs to -y in Makefile.

Signed-off-by: Tracey Dent 
Signed-off-by: Jeff Garzik

[libata] Add ATA transport class

2010-10-22T00:21:03+00:00

This is a scheleton for libata transport class.
All information is read only, exporting information from libata:
- ata_port class: one per ATA port
- ata_link class: one per ATA port or 15 for SATA Port Multiplier
- ata_device class: up to 2 for PATA link, usually one for SATA.

Signed-off-by: Gwendal Grignou 
Reviewed-by: Grant Grundler 
Signed-off-by: Jeff Garzik

libata: remove no longer needed pata_winbond driver

2010-08-25T23:24:15+00:00

Winbond W83759A controller is fully supported by pata_legacy driver
so remove no longer needed pata_winbond driver.

Leave PATA_WINBOND_VLB config option for compatibility reasons
and teach pata_legacy to preserve the old behavior of pata_winbond
driver.

Signed-off-by: Bartlomiej Zolnierkiewicz 
Signed-off-by: Jeff Garzik

Merge branches 'master' and 'devel' into for-linus

2010-08-10T22:17:52+00:00

Conflicts:
	arch/arm/Kconfig
	arch/arm/mm/Kconfig

[libata] Add Samsung PATA controller driver, pata_samsung_cf

2010-08-01T23:36:03+00:00

Adds support for the Samsung PATA controller. This driver is based
on the Libata subsystem and references the earlier patches sent for
IDE subsystem.

Signed-off-by: Abhilash Kesavan 
Signed-off-by: Kukjin Kim 
Cc: Ben Dooks 
Acked-by: Sergei Shtylyov 
Signed-off-by: Jeff Garzik

[libata] Add 460EX on-chip SATA driver, sata_dwc_460ex

2010-08-01T23:36:03+00:00

This patch enables the on-chip DWC SATA controller of the AppliedMicro
processor 460EX.

Signed-off-by: Rupjyoti Sarmah 
Signed-off-by: Mark Miesfeld 
Signed-off-by: Prodyut Hazarika 
Signed-off-by: Jeff Garzik

[ARM] pata_pxa: DMA-capable PATA driver

2010-06-18T07:07:32+00:00

This patch adds a driver for a harddrive attached to PXA address and data bus.
Unlike pata_platform, this driver allows usage of PXA DMA controller, making the
transmission speed 3x higher.

Signed-off-by: Marek Vasut 
Acked-by: Jeff Garzik 
Signed-off-by: Eric Miao

libata-sff: make BMDMA optional

2010-05-25T23:41:12+00:00

Make BMDMA optional depending on new config variable CONFIG_ATA_BMDMA.
In Kconfig, drivers are grouped into five groups - non-SFF native, SFF
w/ custom DMA interface, SFF w/ BMDMA, PIO-only SFF, and generic
fallback / legacy ones.  Kconfig and Makefile are reorganized
according to the groups and ordered alphabetically inside each group.

ata_ioports.bmdma_addr and ata_port.bmdma_prd[_dma] are put into
CONFIG_ATA_BMDMA, as are all bmdma related ops, variables and
functions.

This increase the binary size slightly when BMDMA is enabled but on
both native-only and PIO-only configurations the size is slightly
reduced.  Either way, the size difference is insignificant.  This
change is more meaningful to signify the separation between SFF and
BMDMA and as a tool to verify the separation.

Signed-off-by: Tejun Heo 
Signed-off-by: Jeff Garzik