linux-toradex.git/drivers/ata/libahci.c, branch v3.15-rc6

ahci: disable DEVSLP for Intel Valleyview

2014-04-24T14:26:26+00:00

On Intel Valleyview SoC, SATA device sleep is not reliable. When
DEVSLP is attempted on certain SSDs, port_devslp write would fail
and result in malfunction of AHCI controller. AHCI controller may
be not shown in PCI enumeration after reset. Complete power source
removal may be required to recover from this failure. So we blacklist
this device and override host device reported capabilities such that
device LPM will only attempt slumber but not DEVSLP.

Signed-off-by: Jacob Pan 
Acked-by: Dan Williams 
Signed-off-by: Tejun Heo

ata: remove superfluous casts

2014-03-26T16:36:53+00:00

Unreferenced casts of void * types are unnecessary so remove them.

Signed-off-by: Joe Perches 
Signed-off-by: Tejun Heo

libahci: Allow drivers to override start_engine

2014-02-22T20:35:41+00:00

Allwinner A10 and A20 ARM SoCs have an AHCI sata controller which needs a
special register to be poked before starting the DMA engine.

This register gets reset on an ahci_stop_engine call, so there is no other
place then ahci_start_engine where this poking can be done.

This commit allows drivers to override ahci_start_engine behavior for use by
the Allwinner AHCI driver (and potentially other drivers in the future).

Signed-off-by: Hans de Goede 
Signed-off-by: Tejun Heo

ata: libahci: replace obsolete simple_strtoul() with kstrtouint()

2014-02-20T00:07:55+00:00

Signed-off-by: Daeseok Youn 
Signed-off-by: Tejun Heo

ata: libahci: make ahci_pmp_retry_softreset() as static

2014-02-20T00:07:29+00:00

sparse says:

drivers/ata/libahci.c:1390:5: warning:
 symbol 'ahci_pmp_retry_softreset' was not declared. Should it be static?

Signed-off-by: Daeseok Youn 
Signed-off-by: Tejun Heo

ata: delete non-required instances of include

2014-02-13T21:40:56+00:00

None of these files are actually using any __init type directives
and hence don't need to include .  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

Cc: linux-ide@vger.kernel.org
Signed-off-by: Paul Gortmaker 
Signed-off-by: Tejun Heo

drivers: ata: Mark the function as static in libahci.c

2013-12-14T21:21:42+00:00

This patch marks the function ahci_port_intr() and
ahci_hw_port_interrupt() as static in libahci.c because they are not
used outside this file.

Thus, it also eliminates the following warnings in libahci.c:
drivers/ata/libahci.c:1767:6: warning: no previous prototype for ‘ahci_port_intr’ [-Wmissing-prototypes]
drivers/ata/libahci.c:1800:6: warning: no previous prototype for ‘ahci_hw_port_interrupt’ [-Wmissing-prototypes]

Signed-off-by: Rashika Kheria 
Signed-off-by: Tejun Heo 
Reviewed-by: Josh Triplett

Merge branch 'for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

2013-11-13T06:18:22+00:00

Pull libata changes from Tejun Heo:
 "Nothing too interesting.  Only two minor fixes in libata core.  Most
  changes are specific to hardware which isn't too common"

* 'for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci: Add Device IDs for Intel Wildcat Point-LP
  sata_rcar: Convert to clk_prepare/unprepare
  drivers/libata: Set max sector to 65535 for Slimtype DVD A DS8A9SH drive
  libata: Add some missing command descriptions
  sata_highbank: clear whole array in highbank_initialize_phys()
  ahci: disabled FBS prior to issuing software reset
  libata: Fix display of sata speed
  ahci: imx: setup power saving methods
  ata_piix: minor typo and a printk fix
  ahci: Changing two module params with static and __read_mostly

ahci: disabled FBS prior to issuing software reset

2013-10-27T12:03:04+00:00

Tested with Marvell 88se9125, attached with one port mulitplier(5 ports)
and one disk, we will get following boot log messages if using current
code:

  ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
  ata8.15: Port Multiplier 1.2, 0x1b4b:0x9715 r160, 5 ports, feat 0x1/0x1f
  ahci 0000:03:00.0: FBS is enabled
  ata8.00: hard resetting link
  ata8.00: SATA link down (SStatus 0 SControl 330)
  ata8.01: hard resetting link
  ata8.01: SATA link down (SStatus 0 SControl 330)
  ata8.02: hard resetting link
  ata8.02: SATA link down (SStatus 0 SControl 330)
  ata8.03: hard resetting link
  ata8.03: SATA link up 6.0 Gbps (SStatus 133 SControl 133)
  ata8.04: hard resetting link
  ata8.04: failed to resume link (SControl 133)
  ata8.04: failed to read SCR 0 (Emask=0x40)
  ata8.04: failed to read SCR 0 (Emask=0x40)
  ata8.04: failed to read SCR 1 (Emask=0x40)
  ata8.04: failed to read SCR 0 (Emask=0x40)
  ata8.03: native sectors (2) is smaller than sectors (976773168)
  ata8.03: ATA-8: ST3500413AS, JC4B, max UDMA/133
  ata8.03: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
  ata8.03: configured for UDMA/133
  ata8.04: failed to IDENTIFY (I/O error, err_mask=0x100)
  ata8.15: hard resetting link
  ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
  ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
  ata8.15: PMP revalidation failed (errno=-19)
  ata8.15: hard resetting link
  ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
  ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
  ata8.15: PMP revalidation failed (errno=-19)
  ata8.15: limiting SATA link speed to 3.0 Gbps
  ata8.15: hard resetting link
  ata8.15: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
  ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
  ata8.15: PMP revalidation failed (errno=-19)
  ata8.15: failed to recover PMP after 5 tries, giving up
  ata8.15: Port Multiplier detaching
  ata8.03: disabled
  ata8.00: disabled
  ata8: EH complete

The reason is that current detection code doesn't follow AHCI spec:

First,the port multiplier detection process look like this:

	ahci_hardreset(link, class, deadline)
	if (class == ATA_DEV_PMP) {
		sata_pmp_attach(dev)	/* will enable FBS */
		sata_pmp_init_links(ap, nr_ports);
		ata_for_each_link(link, ap, EDGE) {
			sata_std_hardreset(link, class, deadline);
			if (link_is_online)	/* do soft reset */
				ahci_softreset(link, class, deadline);
		}
	}
But, according to chapter 9.3.9 in AHCI spec: Prior to issuing software
reset, software shall clear PxCMD.ST to '0' and then clear PxFBS.EN to
'0'.

The patch test ok with kernel 3.11.1.

tj: Patch white space contaminated, applied manually with trivial
    updates.

Signed-off-by: Xiangliang Yu 
Signed-off-by: Tejun Heo 
Cc: stable@vger.kernel.org

libahci: fix turning on LEDs in ahci_start_port()

2013-10-15T13:39:57+00:00

If EM Transmit bit is busy during init ata_msleep() is called.  It is
wrong - msleep() should be used instead of ata_msleep(), because if EM
Transmit bit is busy for one port, it will be busy for all other ports
too, so using ata_msleep() causes wasting tries for another ports.

The most common scenario looks like that now
(six ports try to transmit a LED meaasege):
- port #0 tries for the 1st time and succeeds
- ports #1-5 try for the 1st time and sleeps
- port #1 tries for the 2nd time and succeeds
- ports #2-5 try for the 2nd time and sleeps
- port #2 tries for the 3rd time and succeeds
- ports #3-5 try for the 3rd time and sleeps
- port #3 tries for the 4th time and succeeds
- ports #4-5 try for the 4th time and sleeps
- port #4 tries for the 5th time and succeeds
- port #5 tries for the 5th time and sleeps

At this moment port #5 wasted all its five tries and failed to
initialize.  Because there are only 5 (EM_MAX_RETRY) tries available
usually only five ports succeed to initialize. The sixth port and next
ones usually will fail.

If msleep() is used instead of ata_msleep() the first port succeeds to
initialize in the first try and next ones usually succeed to
initialize in the second try.

tj: updated comment

Signed-off-by: Lukasz Dorau 
Signed-off-by: Tejun Heo