linux-toradex.git/drivers/ata/libahci.c, branch v3.2.63

ahci: disabled FBS prior to issuing software reset

2014-01-03T04:33:15+00:00

commit 89dafa20f3daab5b3e0c13d0068a28e8e64e2102 upstream.

Tested with Marvell 88se9125, attached with one port mulitplier(5 ports)
and one disk, we will get following boot log messages if using current
code:

  ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
  ata8.15: Port Multiplier 1.2, 0x1b4b:0x9715 r160, 5 ports, feat 0x1/0x1f
  ahci 0000:03:00.0: FBS is enabled
  ata8.00: hard resetting link
  ata8.00: SATA link down (SStatus 0 SControl 330)
  ata8.01: hard resetting link
  ata8.01: SATA link down (SStatus 0 SControl 330)
  ata8.02: hard resetting link
  ata8.02: SATA link down (SStatus 0 SControl 330)
  ata8.03: hard resetting link
  ata8.03: SATA link up 6.0 Gbps (SStatus 133 SControl 133)
  ata8.04: hard resetting link
  ata8.04: failed to resume link (SControl 133)
  ata8.04: failed to read SCR 0 (Emask=0x40)
  ata8.04: failed to read SCR 0 (Emask=0x40)
  ata8.04: failed to read SCR 1 (Emask=0x40)
  ata8.04: failed to read SCR 0 (Emask=0x40)
  ata8.03: native sectors (2) is smaller than sectors (976773168)
  ata8.03: ATA-8: ST3500413AS, JC4B, max UDMA/133
  ata8.03: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
  ata8.03: configured for UDMA/133
  ata8.04: failed to IDENTIFY (I/O error, err_mask=0x100)
  ata8.15: hard resetting link
  ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
  ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
  ata8.15: PMP revalidation failed (errno=-19)
  ata8.15: hard resetting link
  ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
  ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
  ata8.15: PMP revalidation failed (errno=-19)
  ata8.15: limiting SATA link speed to 3.0 Gbps
  ata8.15: hard resetting link
  ata8.15: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
  ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
  ata8.15: PMP revalidation failed (errno=-19)
  ata8.15: failed to recover PMP after 5 tries, giving up
  ata8.15: Port Multiplier detaching
  ata8.03: disabled
  ata8.00: disabled
  ata8: EH complete

The reason is that current detection code doesn't follow AHCI spec:

First,the port multiplier detection process look like this:

	ahci_hardreset(link, class, deadline)
	if (class == ATA_DEV_PMP) {
		sata_pmp_attach(dev)	/* will enable FBS */
		sata_pmp_init_links(ap, nr_ports);
		ata_for_each_link(link, ap, EDGE) {
			sata_std_hardreset(link, class, deadline);
			if (link_is_online)	/* do soft reset */
				ahci_softreset(link, class, deadline);
		}
	}
But, according to chapter 9.3.9 in AHCI spec: Prior to issuing software
reset, software shall clear PxCMD.ST to '0' and then clear PxFBS.EN to
'0'.

The patch test ok with kernel 3.11.1.

tj: Patch white space contaminated, applied manually with trivial
    updates.

Signed-off-by: Xiangliang Yu 
Signed-off-by: Tejun Heo 
Signed-off-by: Ben Hutchings

ahci: remove pmp link online check in FBS EH

2013-07-27T04:34:08+00:00

commit 912b9ac683b112615d5605686f1dc086402ce9f7 upstream.

ata_link_online() check in ahci_error_intr() is unnecessary, it should
be removed otherwise may lead to lockup with FBS enabled PMP.
http://marc.info/?l=linux-ide&m=137050421603272&w=2

Reported-by: Yu Liu 
Signed-off-by: Shane Huang 
Signed-off-by: Tejun Heo 
Signed-off-by: Ben Hutchings

ahci: move ahci_sb600_softreset to libahci.c and rename it

2011-07-23T21:57:36+00:00

ahci_sb600_softreset was in ahci.c. This function is used
to fix soft reset failure and renames as ahci_pmp_retry_softreset
in libahci.c.

Signed-off-by: Yuan-Hsin Chen 
Signed-off-by: Jeff Garzik

ata: Convert ata__printk(KERN_ to ata__

2011-07-23T21:57:36+00:00

Saves text by removing nearly duplicated text format strings by
creating ata__printk functions and printf extension %pV.

ata defconfig size shrinks ~5% (~8KB), allyesconfig ~2.5% (~13KB)

Format string duplication comes from:

 #define ata_link_printk(link, lv, fmt, args...) do { \
       if (sata_pmp_attached((link)->ap) || (link)->ap->slave_link)    \
               printk("%sata%u.%02u: "fmt, lv, (link)->ap->print_id,   \
                      (link)->pmp , ##args); \
       else \
               printk("%sata%u: "fmt, lv, (link)->ap->print_id , ##args); \
       } while(0)

Coalesce long formats.

$ size drivers/ata/built-in.*
   text	   data	    bss	    dec	    hex	filename
 544969	  73893	 116584	 735446	  b38d6	drivers/ata/built-in.allyesconfig.ata.o
 558429	  73893	 117864	 750186	  b726a	drivers/ata/built-in.allyesconfig.dev_level.o
 141328	  14689	   4220	 160237	  271ed	drivers/ata/built-in.defconfig.ata.o
 149567	  14689	   4220	 168476	  2921c	drivers/ata/built-in.defconfig.dev_level.o

Signed-off-by: Joe Perches 
Signed-off-by: Jeff Garzik

ata: Convert dev_printk(KERN_ to dev_(

2011-07-23T21:57:36+00:00

Saves a bit of text as the call takes fewer args.

Coalesce a few formats.
Convert a few bare printks to pr_cont.

$ size drivers/ata/built-in.o*
   text	   data	    bss	    dec	    hex	filename
 558429	  73893	 117864	 750186	  b726a	drivers/ata/built-in.o.allyesconfig.new
 559574	  73893	 117888	 751355	  b76fb	drivers/ata/built-in.o.allyesconfig.old
 149567	  14689	   4220	 168476	  2921c	drivers/ata/built-in.o.defconfig.new
 149851	  14689	   4220	 168760	  29338	drivers/ata/built-in.o.defconfig.old

Signed-off-by: Joe Perches 
Signed-off-by: Jeff Garzik

ahci: change 'masking port_map' printk to KERN_WARNING level

2011-06-29T17:10:07+00:00

It's not so much an error as a warning about normal Marvell crazines.
So don't use KERN_ERR that ends up spamming the console even in quiet
mode, it's not _that_ critical.

Explained by Jeff:

 "Long explanation, it's a mess:

  Marvell took standard AHCI, and bastardized it to include a weird mode
  whereby PATA devices appear inside the AHCI DMA and interrupt
  infrastructure you're familiar with.

  So, PATA devices appear via pata_marvell driver, using basic legacy
  IDE programming interface.  But SATA devices, which might also be
  attached to this chip, either work in under-performing mode or
  simply don't work at all (e.g.  newer 6 Gbps devices or port
  multiplier attachments, NCQ, ...)

  On the other hand, 'ahci' driver loads and works with the chip's
  attached SATA devices quite beautifully, but is completely unable to
  drive any attached PATA devices, due to the Marvell-specific
  PATA-under-AHCI interface.

  The "masking port_map 0x7 -> 0x3" message is the ahci driver "hiding"
  the PATA port(s) from itself, making sure it will only drive the SATA
  ports it knows how to drive."

Acked-by: Jeff Garzik 
Signed-off-by: Linus Torvalds

Revert "libata: ahci_start_engine compliant to AHCI spec"

2011-05-14T17:45:59+00:00

This reverts commit 270dac35c26433d06a89150c51e75ca0181ca7e4.

The commits causes command timeouts on AC plug/unplug.  It isn't yet
clear why.  As the commit was for a single rather obscure controller,
revert the change for now.

The problem was reported and bisected by Gu Rui in bug#34692.

 https://bugzilla.kernel.org/show_bug.cgi?id=34692

Also, reported by Rafael and Michael in the following thread.

 http://thread.gmane.org/gmane.linux.kernel/1138771

Signed-off-by: Tejun Heo 
Reported-by: Gu Rui 
Reported-by: Rafael J. Wysocki 
Reported-by: Michael Leun 
Cc: Jian Peng 
Cc: Jeff Garzik 
Signed-off-by: Linus Torvalds

libata: ahci_start_engine compliant to AHCI spec

2011-04-24T15:35:40+00:00

At the end of section 10.1 of AHCI spec (rev 1.3), it states

Software shall not set PxCMD.ST to 1 until it is determined that
a functoinal device is present on the port as determined by
PxTFD.STS.BSY=0, PxTFD.STS.DRQ=0 and PxSSTS.DET=3h

Even though most AHCI host controller works without this check,
specific controller will fail under this condition.

Signed-off-by: Jian Peng 
Signed-off-by: Jeff Garzik

ahci: don't enable port irq before handler is registered

2011-04-24T15:34:05+00:00

The ahci_pmp_attach() & ahci_pmp_detach() unmask port irqs, but they
are also called during port initialization, before ahci host irq
handler is registered. On ce4100 platform, this sometimes triggers
"irq 4: nobody cared" message when loading driver.

Fixed this by not touching the register if the port is in frozen
state, and mark all uninitialized port as frozen.

Signed-off-by: Maxime Bizon 
Acked-by: Tejun Heo 
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik

ahci: EM supported message type sysfs attribute

2011-04-24T15:31:31+00:00

This patch adds an sysfs attribute 'em_message_supported' to the
ahci host device which prints out the supported enclosure management
message types.

Signed-off-by: Hannes Reinecke 
Signed-off-by: Jeff Garzik