linux-toradex.git/drivers/ata/pata_oldpiix.c, branch v3.0.9

libata-sff: separate out BMDMA init

2010-05-25T23:40:30+00:00

Separate out ata_pci_bmdma_prepare_host() and ata_pci_bmdma_init_one()
from their SFF counterparts.  SFF ones no longer try to initialize
BMDMA or set PCI master.

Signed-off-by: Tejun Heo 
Signed-off-by: Jeff Garzik

libata-sff: separate out BMDMA qc_issue

2010-05-19T17:38:55+00:00

Separate out ata_bmdma_qc_issue() from ata_sff_qc_issue() such that
ata_sff_qc_issue() only deals with non-BMDMA SFF protocols (PIO and
nodata) while ata_bmdma_qc_issue() deals with the BMDMA protocols and
uses ata_sff_qc_issue() for non-DMA commands.  All the users are
updated accordingly.

Signed-off-by: Tejun Heo 
Signed-off-by: Jeff Garzik

libata: Pass host flags into the pci helper

2010-03-01T19:58:46+00:00

This allows parallel scan and the like to be set without having to stop
using the existing full helper functions. This patch merely adds the argument
and fixes up the callers. It doesn't undo the special cases already in the
tree or add any new parallel callers.

Signed-off-by: Alan Cox 
Signed-off-by: Jeff Garzik

[libata] MWDMA0 is unsupported on PIIX-like PATA controllers

2009-12-03T22:52:16+00:00

MWDMA0 timings cannot be met with the PIIX based controller
programming interface.

Signed-off-by: Bartlomiej Zolnierkiewicz 
Acked-by: Sergei Shtylyov 
Signed-off-by: Jeff Garzik

[libata] convert drivers to use ata.h mode mask defines

2009-03-25T02:13:27+00:00

No functional changes in this patch.

Signed-off-by: Erik Inge Bolsø 
Signed-off-by: Jeff Garzik

[libata] Update kernel-doc comments to match source code

2008-12-29T03:43:21+00:00

Signed-off-by: Qinghuang Feng

ata: Switch all my stuff to a common address

2008-10-28T03:54:50+00:00

Signed-off-by: Jeff Garzik

libata: Fix a large collection of DMA mode mismatches

2008-08-22T06:27:49+00:00

Dave Müller sent a diff for the pata_oldpiix that highlighted a problem
where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while
the core code uses 0xFF.

This turns out to have other consequences such as code doing >= XFER_UDMA_0
also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect
set_dma_mode, although some drivers call back into their own set mode code
from other points.

Having been through the drivers I've added helpers for using_udma/using_mwdma
dma_enabled so that people don't open code ranges that may change (eg if UDMA8
appears somewhere)

Thanks to David for the initial bits
[and added fix for pata_oldpiix from and signed-off-by Dave Mueller
   -jg]

Signed-off-by: Alan Cox 
Signed-off-by: Jeff Garzik

libata: rename SFF functions

2008-04-17T19:44:21+00:00

SFF functions have confusing names.  Some have sff prefix, some have
bmdma, some std, some pci and some none.  Unify the naming by...

* SFF functions which are common to both BMDMA and non-BMDMA are
  prefixed with ata_sff_.

* SFF functions which are specific to BMDMA are prefixed with
  ata_bmdma_.

* SFF functions which are specific to PCI but apply to both BMDMA and
  non-BMDMA are prefixed with ata_pci_sff_.

* SFF functions which are specific to PCI and BMDMA are prefixed with
  ata_pci_bmdma_.

* Drop generic prefixes from LLD specific routines.  For example,
  bfin_std_dev_select -> bfin_dev_select.

The following renames are noteworthy.

  ata_qc_issue_prot() -> ata_sff_qc_issue()
  ata_pci_default_filter() -> ata_bmdma_mode_filter()
  ata_dev_try_classify() -> ata_sff_dev_classify()

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames functions and doesn't
introduce any behavior difference.

Signed-off-by: Tejun Heo

libata: make reset related methods proper port operations

2008-04-17T19:44:18+00:00

Currently reset methods are not specified directly in the
ata_port_operations table.  If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods.  It's done this way for two reasons.

First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.

Second, as ->error_handler uses those reset methods, it can get
confusing.  ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.

Now that ops table uses inheritance, the first problem doesn't exist
anymore.  The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks.  In fact, there currently is no driver which actually
modifies error handling behavior.  Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH.  I don't think making ops layering strict has
any noticeable benefit.

This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops.  Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.

* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
  aren't accessible.  sata_promise doesn't need to use separate
  error_handlers for PATA and SATA anymore.

* softreset is broken for sata_inic162x and sata_sx4.  As libata now
  always prefers hardreset, this doesn't really matter but the ops are
  forced to NULL using ATA_OP_NULL for documentation purpose.

* pata_hpt374 needs to use different prereset for the first and second
  PCI functions.  This used to be done by branching from
  hpt374_error_handler().  The proper way to do this is to use
  separate ops and port_info tables for each function.  Converted.

Signed-off-by: Tejun Heo