linux-toradex.git/drivers/ata, branch v3.10.62

ahci: disable MSI instead of NCQ on Samsung pci-e SSDs on macbooks

2014-11-21T17:22:52+00:00

commit 66a7cbc303f4d28f201529b06061944d51ab530c upstream.

Samsung pci-e SSDs on macbooks failed miserably on NCQ commands, so
67809f85d31e ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks")
disabled NCQ on them.  It turns out that NCQ is fine as long as MSI is
not used, so let's turn off MSI and leave NCQ on.

Signed-off-by: Tejun Heo 
Link: https://bugzilla.kernel.org/show_bug.cgi?id=60731
Tested-by: 
Tested-by: Imre Kaloz 
Fixes: 67809f85d31e ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks")
Signed-off-by: Greg Kroah-Hartman

ahci: Add Device IDs for Intel Sunrise Point PCH

2014-11-21T17:22:52+00:00

commit 690000b930456a98663567d35dd5c54b688d1e3f upstream.

This patch adds the AHCI-mode SATA Device IDs for the Intel Sunrise Point PCH.

Signed-off-by: James Ralston 
Signed-off-by: Tejun Heo 
Signed-off-by: Greg Kroah-Hartman

libata-sff: Fix controllers with no ctl port

2014-11-14T16:47:53+00:00

commit 6d8ca28fa688a9354bc9fbc935bdaeb3651b6677 upstream.

Currently, ata_sff_softreset is skipped for controllers with no ctl port.
But that also skips ata_sff_dev_classify required for device detection.
This means that libata is currently broken on controllers with no ctl port.

No device connected:
[    1.872480] pata_isapnp 01:01.02: activated
[    1.889823] scsi2 : pata_isapnp
[    1.890109] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11
[    6.888110] ata3.01: qc timeout (cmd 0xec)
[    6.888179] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   16.888085] ata3.01: qc timeout (cmd 0xec)
[   16.888147] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   46.888086] ata3.01: qc timeout (cmd 0xec)
[   46.888148] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   51.888100] ata3.00: qc timeout (cmd 0xec)
[   51.888160] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)
[   61.888079] ata3.00: qc timeout (cmd 0xec)
[   61.888141] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)
[   91.888089] ata3.00: qc timeout (cmd 0xec)
[   91.888152] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)

ATAPI device connected:
[    1.882061] pata_isapnp 01:01.02: activated
[    1.893430] scsi2 : pata_isapnp
[    1.893719] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11
[    6.892107] ata3.01: qc timeout (cmd 0xec)
[    6.892171] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   16.892079] ata3.01: qc timeout (cmd 0xec)
[   16.892138] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   46.892079] ata3.01: qc timeout (cmd 0xec)
[   46.892138] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   46.908586] ata3.00: ATAPI: ACER CD-767E/O, V1.5X, max PIO2, CDB intr
[   46.924570] ata3.00: configured for PIO0 (device error ignored)
[   46.926295] scsi 2:0:0:0: CD-ROM            ACER     CD-767E/O        1.5X PQ: 0 ANSI: 5
[   46.984519] sr0: scsi3-mmc drive: 6x/6x xa/form2 tray
[   46.984592] cdrom: Uniform CD-ROM driver Revision: 3.20

So don't skip ata_sff_softreset, just skip the reset part of ata_bus_softreset
if the ctl port is not available.

This makes IDE port on ES968 behave correctly:

No device connected:
[    4.670888] pata_isapnp 01:01.02: activated
[    4.673207] scsi host2: pata_isapnp
[    4.673675] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11
[    7.081840] Adding 2541652k swap on /dev/sda2.  Priority:-1 extents:1 across:2541652k

ATAPI device connected:
[    4.704362] pata_isapnp 01:01.02: activated
[    4.706620] scsi host2: pata_isapnp
[    4.706877] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11
[    4.872782] ata3.00: ATAPI: ACER CD-767E/O, V1.5X, max PIO2, CDB intr
[    4.888673] ata3.00: configured for PIO0 (device error ignored)
[    4.893984] scsi 2:0:0:0: CD-ROM            ACER     CD-767E/O        1.5X PQ: 0 ANSI: 5
[    7.015578] Adding 2541652k swap on /dev/sda2.  Priority:-1 extents:1 across:2541652k

Signed-off-by: Ondrej Zary 
Signed-off-by: Tejun Heo 
Signed-off-by: Greg Kroah-Hartman

pata_serverworks: disable 64-KB DMA transfers on Broadcom OSB4 IDE Controller

2014-11-14T16:47:53+00:00

commit 37017ac6849e772e67dd187ba2fbd056c4afa533 upstream.

The Broadcom OSB4 IDE Controller (vendor and device IDs: 1166:0211)
does not support 64-KB DMA transfers.
Whenever a 64-KB DMA transfer is attempted,
the transfer fails and messages similar to the following
are written to the console log:

   [ 2431.851125] sr 0:0:0:0: [sr0] Unhandled sense code
   [ 2431.851139] sr 0:0:0:0: [sr0]  Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
   [ 2431.851152] sr 0:0:0:0: [sr0]  Sense Key : Hardware Error [current]
   [ 2431.851166] sr 0:0:0:0: [sr0]  Add. Sense: Logical unit communication time-out
   [ 2431.851182] sr 0:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 76 f4 00 00 40 00
   [ 2431.851210] end_request: I/O error, dev sr0, sector 121808

When the libata and pata_serverworks modules
are recompiled with ATA_DEBUG and ATA_VERBOSE_DEBUG defined in libata.h,
the 64-KB transfer size in the scatter-gather list can be seen
in the console log:

   [ 2664.897267] sr 9:0:0:0: [sr0] Send:
   [ 2664.897274] 0xf63d85e0
   [ 2664.897283] sr 9:0:0:0: [sr0] CDB:
   [ 2664.897288] Read(10): 28 00 00 00 7f b4 00 00 40 00
   [ 2664.897319] buffer = 0xf6d6fbc0, bufflen = 131072, queuecommand 0xf81b7700
   [ 2664.897331] ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 7f b4 00 00 40
   [ 2664.897338] ata_scsi_translate: ENTER
   [ 2664.897345] ata_sg_setup: ENTER, ata1
   [ 2664.897356] ata_sg_setup: 3 sg elements mapped
   [ 2664.897364] ata_bmdma_fill_sg: PRD[0] = (0x66FD2000, 0xE000)
   [ 2664.897371] ata_bmdma_fill_sg: PRD[1] = (0x65000000, 0x10000)
   ------------------------------------------------------> =======
   [ 2664.897378] ata_bmdma_fill_sg: PRD[2] = (0x66A10000, 0x2000)
   [ 2664.897386] ata1: ata_dev_select: ENTER, device 0, wait 1
   [ 2664.897422] ata_sff_tf_load: feat 0x1 nsect 0x0 lba 0x0 0x0 0xFC
   [ 2664.897428] ata_sff_tf_load: device 0xA0
   [ 2664.897448] ata_sff_exec_command: ata1: cmd 0xA0
   [ 2664.897457] ata_scsi_translate: EXIT
   [ 2664.897462] leaving scsi_dispatch_cmnd()
   [ 2664.897497] Doing sr request, dev = sr0, block = 0
   [ 2664.897507] sr0 : reading 64/256 512 byte blocks.
   [ 2664.897553] ata_sff_hsm_move: ata1: protocol 7 task_state 1 (dev_stat 0x58)
   [ 2664.897560] atapi_send_cdb: send cdb
   [ 2666.910058] ata_bmdma_port_intr: ata1: host_stat 0x64
   [ 2666.910079] __ata_sff_port_intr: ata1: protocol 7 task_state 3
   [ 2666.910093] ata_sff_hsm_move: ata1: protocol 7 task_state 3 (dev_stat 0x51)
   [ 2666.910101] ata_sff_hsm_move: ata1: protocol 7 task_state 4 (dev_stat 0x51)
   [ 2666.910129] sr 9:0:0:0: [sr0] Done:
   [ 2666.910136] 0xf63d85e0 TIMEOUT

lspci shows that the driver used for the Broadcom OSB4 IDE Controller is
pata_serverworks:

   00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8e [Master SecP SecO PriP])
           Flags: bus master, medium devsel, latency 64
           [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
           [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
           I/O ports at 0170 [size=8]
           I/O ports at 0374 [size=4]
           I/O ports at 1440 [size=16]
           Kernel driver in use: pata_serverworks

The pata_serverworks driver supports five distinct device IDs,
one being the OSB4 and the other four belonging to the CSB series.
The CSB series appears to support 64-KB DMA transfers,
as tests on a machine with an SAI2 motherboard
containing a Broadcom CSB5 IDE Controller (vendor and device IDs: 1166:0212)
showed no problems with 64-KB DMA transfers.

This problem was first discovered when attempting to install openSUSE
from a DVD on a machine with an STL2 motherboard.
Using the pata_serverworks module,
older releases of openSUSE will not install at all due to the timeouts.
Releases of openSUSE prior to 11.3 can be installed by disabling
the pata_serverworks module using the brokenmodules boot parameter,
which causes the serverworks module to be used instead.
Recent releases of openSUSE (12.2 and later) include better error recovery and
will install, though very slowly.
On all openSUSE releases, the problem can be recreated
on a machine containing a Broadcom OSB4 IDE Controller
by mounting an install DVD and running a command similar to the following:

   find /mnt -type f -print | xargs cat > /dev/null

The patch below corrects the problem.
Similar to the other ATA drivers that do not support 64-KB DMA transfers,
the patch changes the ata_port_operations qc_prep vector to point to a routine
that breaks any 64-KB segment into two 32-KB segments and
changes the scsi_host_template sg_tablesize element to reduce by half
the number of scatter/gather elements allowed.
These two changes affect only the OSB4.

Signed-off-by: Scott Carter 
Signed-off-by: Tejun Heo 
Signed-off-by: Greg Kroah-Hartman

ata_piix: Add Device IDs for Intel 9 Series PCH

2014-10-05T21:54:13+00:00

commit 6cad1376954e591c3c41500c4e586e183e7ffe6d upstream.

This patch adds the IDE mode SATA Device IDs for the Intel 9 Series PCH.

Signed-off-by: James Ralston 
Signed-off-by: Tejun Heo 
Signed-off-by: Greg Kroah-Hartman

ahci: add pcid for Marvel 0x9182 controller

2014-10-05T21:54:07+00:00

commit c5edfff9db6f4d2c35c802acb4abe0df178becee upstream.

Keystone K2E EVM uses Marvel 0x9182 controller. This requires support
for the ID in the ahci driver.

Signed-off-by: Murali Karicheri 
Signed-off-by: Tejun Heo 
Cc: Santosh Shilimkar 
Signed-off-by: Greg Kroah-Hartman

ahci: Add Device IDs for Intel 9 Series PCH

2014-10-05T21:54:07+00:00

commit 1b071a0947dbce5c184c12262e02540fbc493457 upstream.

This patch adds the AHCI mode SATA Device IDs for the Intel 9 Series PCH.

Signed-off-by: James Ralston 
Signed-off-by: Tejun Heo 
Signed-off-by: Greg Kroah-Hartman

pata_scc: propagate return value of scc_wait_after_reset

2014-10-05T21:54:07+00:00

commit 4dc7c76cd500fa78c64adfda4b070b870a2b993c upstream.

scc_bus_softreset not necessarily should return zero.
Propagate the error code.

Signed-off-by: Arjun Sreedharan 
Signed-off-by: Tejun Heo 
Signed-off-by: Greg Kroah-Hartman

ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)

2014-07-31T19:53:49+00:00

commit b32bfc06aefab61acc872dec3222624e6cd867ed upstream.

Add support of the Promise FastTrak TX8660 SATA HBA in ahci mode by
registering the board in the ahci_pci_tbl[].

Note: this HBA also provide a hardware RAID mode when activated in
BIOS but specific drivers from the manufacturer are required in this
case.

Signed-off-by: Romain Degez 
Tested-by: Romain Degez 
Signed-off-by: Tejun Heo 
Signed-off-by: Greg Kroah-Hartman

libata: introduce ata_host->n_tags to avoid oops on SAS controllers

2014-07-31T19:53:49+00:00

commit 1a112d10f03e83fb3a2fdc4c9165865dec8a3ca6 upstream.

1871ee134b73 ("libata: support the ata host which implements a queue
depth less than 32") directly used ata_port->scsi_host->can_queue from
ata_qc_new() to determine the number of tags supported by the host;
unfortunately, SAS controllers doing SATA don't initialize ->scsi_host
leading to the following oops.

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
 IP: [] ata_qc_new_init+0x188/0x1b0
 PGD 0
 Oops: 0002 [#1] SMP
 Modules linked in: isci libsas scsi_transport_sas mgag200 drm_kms_helper ttm
 CPU: 1 PID: 518 Comm: udevd Not tainted 3.16.0-rc6+ #62
 Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.02.0002.122320131210 12/23/2013
 task: ffff880c1a00b280 ti: ffff88061a000000 task.ti: ffff88061a000000
 RIP: 0010:[]  [] ata_qc_new_init+0x188/0x1b0
 RSP: 0018:ffff88061a003ae8  EFLAGS: 00010012
 RAX: 0000000000000001 RBX: ffff88000241ca80 RCX: 00000000000000fa
 RDX: 0000000000000020 RSI: 0000000000000020 RDI: ffff8806194aa298
 RBP: ffff88061a003ae8 R08: ffff8806194a8000 R09: 0000000000000000
 R10: 0000000000000000 R11: ffff88000241ca80 R12: ffff88061ad58200
 R13: ffff8806194aa298 R14: ffffffff814e67a0 R15: ffff8806194a8000
 FS:  00007f3ad7fe3840(0000) GS:ffff880627620000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000058 CR3: 000000061a118000 CR4: 00000000001407e0
 Stack:
  ffff88061a003b20 ffffffff814e96e1 ffff88000241ca80 ffff88061ad58200
  ffff8800b6bf6000 ffff880c1c988000 ffff880619903850 ffff88061a003b68
  ffffffffa0056ce1 ffff88061a003b48 0000000013d6e6f8 ffff88000241ca80
 Call Trace:
  [] ata_sas_queuecmd+0xa1/0x430
  [] sas_queuecommand+0x191/0x220 [libsas]
  [] scsi_dispatch_cmd+0x10e/0x300 [] scsi_request_fn+0x2f5/0x550
  [] __blk_run_queue+0x33/0x40
  [] queue_unplugged+0x2a/0x90
  [] blk_flush_plug_list+0x1b4/0x210
  [] blk_finish_plug+0x14/0x50
  [] __do_page_cache_readahead+0x198/0x1f0
  [] force_page_cache_readahead+0x31/0x50
  [] page_cache_sync_readahead+0x3e/0x50
  [] generic_file_read_iter+0x496/0x5a0
  [] blkdev_read_iter+0x37/0x40
  [] new_sync_read+0x7e/0xb0
  [] vfs_read+0x94/0x170
  [] SyS_read+0x46/0xb0
  [] ? SyS_lseek+0x91/0xb0
  [] system_call_fastpath+0x16/0x1b
 Code: 00 00 00 88 50 29 83 7f 08 01 19 d2 83 e2 f0 83 ea 50 88 50 34 c6 81 1d 02 00 00 40 c6 81 17 02 00 00 00 5d c3 66 0f 1f 44 00 00 <89> 14 25 58 00 00 00

Fix it by introducing ata_host->n_tags which is initialized to
ATA_MAX_QUEUE - 1 in ata_host_init() for SAS controllers and set to
scsi_host_template->can_queue in ata_host_register() for !SAS ones.
As SAS hosts are never registered, this will give them the same
ATA_MAX_QUEUE - 1 as before.  Note that we can't use
scsi_host->can_queue directly for SAS hosts anyway as they can go
higher than the libata maximum.

Signed-off-by: Tejun Heo 
Reported-by: Mike Qiu 
Reported-by: Jesse Brandeburg 
Reported-by: Peter Hurley 
Reported-by: Peter Zijlstra 
Tested-by: Alexey Kardashevskiy 
Fixes: 1871ee134b73 ("libata: support the ata host which implements a queue depth less than 32")
Cc: Kevin Hao 
Cc: Dan Williams 
Signed-off-by: Greg Kroah-Hartman