linux-toradex.git/drivers/block, branch v3.2.36

floppy: properly handle failure on add_disk loop

2012-11-16T16:47:00+00:00

commit d60e7ec18c3fb2cbf90969ccd42889eb2d03aef9 upstream.

On floppy initialization, if something failed inside the loop we call
add_disk, there was no cleanup of previous iterations in the error
handling.

Signed-off-by: Herton Ronaldo Krzesinski 
Signed-off-by: Jiri Kosina 
Signed-off-by: Jens Axboe 
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings

floppy: do put_disk on current dr if blk_init_queue fails

2012-11-16T16:46:59+00:00

commit 238ab78469c6ab7845b43d5061cd3c92331b2452 upstream.

If blk_init_queue fails, we do not call put_disk on the current dr
(dr is decremented first in the error handling loop).

Reviewed-by: Ben Hutchings 
Signed-off-by: Herton Ronaldo Krzesinski 
Signed-off-by: Jiri Kosina 
Signed-off-by: Jens Axboe 
Signed-off-by: Ben Hutchings

x86: Remove the ancient and deprecated disable_hlt() and enable_hlt() facility

2012-11-16T16:46:46+00:00

commit f6365201d8a21fb347260f89d6e9b3e718d63c70 upstream.

The X86_32-only disable_hlt/enable_hlt mechanism was used by the
32-bit floppy driver. Its effect was to replace the use of the
HLT instruction inside default_idle() with cpu_relax() - essentially
it turned off the use of HLT.

This workaround was commented in the code as:

 "disable hlt during certain critical i/o operations"

 "This halt magic was a workaround for ancient floppy DMA
  wreckage. It should be safe to remove."

H. Peter Anvin additionally adds:

 "To the best of my knowledge, no-hlt only existed because of
  flaky power distributions on 386/486 systems which were sold to
  run DOS.  Since DOS did no power management of any kind,
  including HLT, the power draw was fairly uniform; when exposed
  to the much hhigher noise levels you got when Linux used HLT
  caused some of these systems to fail.

  They were by far in the minority even back then."

Alan Cox further says:

 "Also for the Cyrix 5510 which tended to go castors up if a HLT
  occurred during a DMA cycle and on a few other boxes HLT during
  DMA tended to go astray.

  Do we care ? I doubt it. The 5510 was pretty obscure, the 5520
  fixed it, the 5530 is probably the oldest still in any kind of
  use."

So, let's finally drop this.

Signed-off-by: Len Brown 
Signed-off-by: Josh Boyer 
Signed-off-by: Andrew Morton 
Acked-by: "H. Peter Anvin" 
Acked-by: Alan Cox 
Cc: Stephen Hemminger 
Link: http://lkml.kernel.org/n/tip-3rhk9bzf0x9rljkv488tloib@git.kernel.org
[ If anyone cares then alternative instruction patching could be
  used to replace HLT with a one-byte NOP instruction. Much simpler. ]
Signed-off-by: Ingo Molnar 
[bwh: Backported to 3.2: adjust filename, context]
Signed-off-by: Ben Hutchings

aoe: assert AoE packets marked as requiring no checksum

2012-10-10T02:31:34+00:00

[ Upstream commit 8babe8cc6570ed896b7b596337eb8fe730c3ff45 ]

In order for the network layer to see that AoE requires
no checksumming in a generic way, the packets must be
marked as requiring no checksum, so we make this requirement
explicit with the assertion.

Signed-off-by: Ed Cashin 
Signed-off-by: David S. Miller 
Signed-off-by: Ben Hutchings

cciss: fix handling of protocol error

2012-10-10T02:30:48+00:00

commit 2453f5f992717251cfadab6184fbb3ec2f2e8b40 upstream.

If a command completes with a status of CMD_PROTOCOL_ERR, this
information should be conveyed to the SCSI mid layer, not dropped
on the floor.  Unlike a similar bug in the hpsa driver, this bug
only affects tape drives and CD and DVD ROM drives in the cciss
driver, and to induce it, you have to disconnect (or damage) a
cable, so it is not a very likely scenario (which would explain
why the bug has gone undetected for the last 10 years.)

Signed-off-by: Stephen M. Cameron 
Signed-off-by: Jens Axboe 
Signed-off-by: Ben Hutchings

nbd: clear waiting_queue on shutdown

2012-10-10T02:30:46+00:00

commit fded4e090c60100d709318896c79816d68d5b47d upstream.

Fix a serious but uncommon bug in nbd which occurs when there is heavy
I/O going to the nbd device while, at the same time, a failure (server,
network) or manual disconnect of the nbd connection occurs.

There is a small window between the time that the nbd_thread is stopped
and the socket is shutdown where requests can continue to be queued to
nbd's internal waiting_queue.  When this happens, those requests are
never completed or freed.

The fix is to clear the waiting_queue on shutdown of the nbd device, in
the same way that the nbd request queue (queue_head) is already being
cleared.

Signed-off-by: Paul Clements 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds 
[bwh: Backported to 3.2: local nbd_device pointers are called 'lo' not 'nbd']
Signed-off-by: Ben Hutchings

virtio-blk: Reset device after blk_cleanup_queue()

2012-09-12T02:37:33+00:00

commit 483001c765af6892b3fc3726576cb42f17d1d6b5 upstream.

blk_cleanup_queue() will call blk_drian_queue() to drain all the
requests before queue DEAD marking. If we reset the device before
blk_cleanup_queue() the drain would fail.

1) if the queue is stopped in do_virtblk_request() because device is
full, the q->request_fn() will not be called.

blk_drain_queue() {
   while(true) {
      ...
      if (!list_empty(&q->queue_head))
        __blk_run_queue(q) {
	    if (queue is not stoped)
		q->request_fn()
	}
      ...
   }
}

Do no reset the device before blk_cleanup_queue() gives the chance to
start the queue in interrupt handler blk_done().

2) In commit b79d866c8b7014a51f611a64c40546109beaf24a, We abort requests
dispatched to driver before blk_cleanup_queue(). There is a race if
requests are dispatched to driver after the abort and before the queue
DEAD mark. To fix this, instead of aborting the requests explicitly, we
can just reset the device after after blk_cleanup_queue so that the
device can complete all the requests before queue DEAD marking in the
drain process.

Cc: Rusty Russell 
Cc: virtualization@lists.linux-foundation.org
Cc: kvm@vger.kernel.org
Signed-off-by: Asias He 
Acked-by: Michael S. Tsirkin 
Signed-off-by: Rusty Russell 
Signed-off-by: Ben Hutchings

virtio-blk: Call del_gendisk() before disable guest kick

2012-09-12T02:37:33+00:00

commit 02e2b124943648fba0a2ccee5c3656a5653e0151 upstream.

del_gendisk() might not return due to failing to remove the
/sys/block/vda/serial sysfs entry when another thread (udev) is
trying to read it.

virtblk_remove()
  vdev->config->reset() : guest will not kick us through interrupt
    del_gendisk()
      device_del()
        kobject_del(): got stuck, sysfs entry ref count non zero

sysfs_open_file(): user space process read /sys/block/vda/serial
   sysfs_get_active() : got sysfs entry ref count
      dev_attr_show()
        virtblk_serial_show()
           blk_execute_rq() : got stuck, interrupt is disabled
                              request cannot be finished

This patch fixes it by calling del_gendisk() before we disable guest's
interrupt so that the request sent in virtblk_serial_show() will be
finished and del_gendisk() will success.

This fixes another race in hot-unplug process.

It is save to call del_gendisk(vblk->disk) before
flush_work(&vblk->config_work) which might access vblk->disk, because
vblk->disk is not freed until put_disk(vblk->disk).

Cc: virtualization@lists.linux-foundation.org
Cc: kvm@vger.kernel.org
Signed-off-by: Asias He 
Acked-by: Michael S. Tsirkin 
Signed-off-by: Rusty Russell 
Signed-off-by: Ben Hutchings

virtio-blk: Fix hot-unplug race in remove method

2012-09-12T02:37:32+00:00

commit b79d866c8b7014a51f611a64c40546109beaf24a upstream.

If we reset the virtio-blk device before the requests already dispatched
to the virtio-blk driver from the block layer are finised, we will stuck
in blk_cleanup_queue() and the remove will fail.

blk_cleanup_queue() calls blk_drain_queue() to drain all requests queued
before DEAD marking. However it will never success if the device is
already stopped. We'll have q->in_flight[] > 0, so the drain will not
finish.

How to reproduce the race:
1. hot-plug a virtio-blk device
2. keep reading/writing the device in guest
3. hot-unplug while the device is busy serving I/O

Test:
~1000 rounds of hot-plug/hot-unplug test passed with this patch.

Changes in v3:
- Drop blk_abort_queue and blk_abort_request
- Use __blk_end_request_all to complete request dispatched to driver

Changes in v2:
- Drop req_in_flight
- Use virtqueue_detach_unused_buf to get request dispatched to driver

Signed-off-by: Asias He 
Signed-off-by: Rusty Russell 
Signed-off-by: Ben Hutchings

virtio_blk: Drop unused request tracking list

2012-09-12T02:37:31+00:00

commit f65ca1dc6a8c81c6bd72297d4399ec5f4c1f3a01 upstream.

Benchmark shows small performance improvement on fusion io device.

Before:
  seq-read : io=1,024MB, bw=19,982KB/s, iops=39,964, runt= 52475msec
  seq-write: io=1,024MB, bw=20,321KB/s, iops=40,641, runt= 51601msec
  rnd-read : io=1,024MB, bw=15,404KB/s, iops=30,808, runt= 68070msec
  rnd-write: io=1,024MB, bw=14,776KB/s, iops=29,552, runt= 70963msec

After:
  seq-read : io=1,024MB, bw=20,343KB/s, iops=40,685, runt= 51546msec
  seq-write: io=1,024MB, bw=20,803KB/s, iops=41,606, runt= 50404msec
  rnd-read : io=1,024MB, bw=16,221KB/s, iops=32,442, runt= 64642msec
  rnd-write: io=1,024MB, bw=15,199KB/s, iops=30,397, runt= 68991msec

Signed-off-by: Asias He 
Signed-off-by: Rusty Russell 
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings