linux-toradex.git/drivers/bluetooth, branch v4.16

Bluetooth: hci_bcm: Set pulsed_host_wake flag in sleep parameters

2018-03-15T18:39:37+00:00

The IRQ output of the bcm bt-device is really a level IRQ signal, which
signals a logical high as long as the device's buffer contains data. Since
the draining in the buffer is done in the tty driver, we cannot (easily)
wait in a threaded interrupt handler for the draining, after which the
IRQ should go low again.

So instead we treat the IRQ as an edge interrupt. This opens the window
for a theoretical race where we wakeup, read some data and then autosuspend
*before* the IRQ has gone (logical) low, followed by the device just at
that moment receiving more data, causing the IRQ to stay high and we never
see an edge.

Since we call pm_runtime_mark_last_busy() on every received byte, there
should be plenty time for the IRQ to go (logical) low before we ever
suspend, so this should never happen, but after commit 43fff7683468
("Bluetooth: hci_bcm: Streamline runtime PM code"), which has been reverted
since, this was actually happening causing the device to get stuck in
runtime suspend.

The bcm bt-device actually has a workaround for this, if we set the
pulsed_host_wake flag in the sleep parameters, then the device monitors
if the host is draining the buffer and if not then after a timeout the
device will pulse the IRQ line, causing us to see an edge, fixing the
stuck in suspend condition.

This commit sets the pulsed_host_wake flag to fix the (mostly theoretical)
race caused by us treating the IRQ as an edge IRQ.

Signed-off-by: Hans de Goede 
Reviewed-by: Lukas Wunner 
Signed-off-by: Marcel Holtmann

Revert "Bluetooth: hci_bcm: Streamline runtime PM code"

2018-03-15T18:39:37+00:00

This reverts commit 43fff7683468 ("Bluetooth: hci_bcm: Streamline runtime
PM code"). The commit msg for this commit states "No functional change
intended.", but replacing:

 pm_runtime_get();
 pm_runtime_mark_last_busy();
 pm_runtime_put_autosuspend();

with:

 pm_request_resume();

Does result in a functional change, pm_request_resume() only calls
pm_runtime_mark_last_busy() if the device was suspended before the call.

This results in the following happening:

1) Device is runtime suspended
2) Device drives host_wake IRQ logically high as it starts receiving data
3) bcm_host_wake() gets called, causes the device to runtime-resume,
   current time gets marked as last_busy time
4) After 5 seconds the autosuspend timer expires and the dev autosuspends
   as no one has been calling pm_runtime_mark_last_busy(), the device was
   resumed during those 5 seconds, so all the pm_request_resume() calls
   while receiving data and/or bcm_host_wake() calls were nops
5) If 4) happens while the device has (just received) data in its buffer to
   be read by the host the IRQ line is *already* / still logically high
   when we autosuspend and since we use an edge triggered IRQ, the IRQ
   will never trigger, causing the device to get stuck in suspend

Therefor this commit has to be reverted, so that we avoid the device
getting stuck in suspend.

Signed-off-by: Hans de Goede 
Acked-by: Lukas Wunner 
Signed-off-by: Marcel Holtmann

Bluetooth: btusb: Fix quirk for Atheros 1525/QCA6174

2018-03-15T18:39:15+00:00

The Atheros 1525/QCA6174 BT doesn't seem working properly on the
recent kernels, as it tries to load a wrong firmware
ar3k/AthrBT_0x00000200.dfu and it fails.

This seems to have been a problem for some time, and the known
workaround is to apply BTUSB_QCA_ROM quirk instead of BTUSB_ATH3012.

The device in question is:

T: Bus=01 Lev=01 Prnt=01 Port=09 Cnt=03 Dev#=  4 Spd=12   MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P: Vendor=0cf3 ProdID=3004 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=1082504
Reported-by: Ivan Levshin 
Tested-by: Ivan Levshin 
Cc: 
Signed-off-by: Takashi Iwai 
Signed-off-by: Marcel Holtmann

Bluetooth: btusb: Add Dell OptiPlex 3060 to btusb_needs_reset_resume_table

2018-03-01T18:55:56+00:00

The issue can be reproduced before commit fd865802c66b ("Bluetooth:
btusb: fix QCA Rome suspend/resume") gets introduced, so the reset
resume quirk is still needed for this system.

T:  Bus=01 Lev=01 Prnt=01 Port=13 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e007 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Cc: stable@vger.kernel.org
Cc: Brian Norris 
Cc: Hans de Goede 
Signed-off-by: Kai-Heng Feng 
Signed-off-by: Marcel Holtmann

Bluetooth: btusb: Remove Yoga 920 from the btusb_needs_reset_resume_table

2018-03-01T18:55:56+00:00

Commit 1fdb92697469 ("Bluetooth: btusb: Use DMI matching for QCA
reset_resume quirking"), added the Lenovo Yoga 920 to the
btusb_needs_reset_resume_table.

Testing has shown that this is a false positive and the problems where
caused by issues with the initial fix: commit fd865802c66b ("Bluetooth:
btusb: fix QCA Rome suspend/resume"), which has already been reverted.

So the QCA Rome BT in the Yoga 920 does not need a reset-resume quirk at
all and this commit removes it from the btusb_needs_reset_resume_table.

Note that after this commit the btusb_needs_reset_resume_table is now
empty. It is kept around on purpose, since this whole series of commits
started for a reason and there are actually broken platforms around,
which need to be added to it.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Fixes: 1fdb92697469 ("Bluetooth: btusb: Use DMI matching for QCA ...")
Cc: stable@vger.kernel.org
Cc: Brian Norris 
Cc: Kai-Heng Feng 
Tested-by: Kevin Fenzi 
Suggested-by: Brian Norris 
Signed-off-by: Hans de Goede 
Reviewed-by: Brian Norris 
Signed-off-by: Marcel Holtmann

Bluetooth: hci_bcm: Make shutdown and device wake GPIO optional

2018-02-25T20:08:28+00:00

According to the devicetree binding the shutdown and device wake
GPIOs are optional. Since commit 3e81a4ca51a1 ("Bluetooth: hci_bcm:
Mandate presence of shutdown and device wake GPIO") this driver
won't probe anymore on Raspberry Pi 3 and Zero W (no device wake GPIO
connected). So fix this regression by reverting this commit partially.

Fixes: 3e81a4ca51a1 ("Bluetooth: hci_bcm: Mandate presence of shutdown and device wake GPIO")
Signed-off-by: Stefan Wahren 
Reviewed-by: Lukas Wunner 
Signed-off-by: Marcel Holtmann

Bluetooth: btusb: Use DMI matching for QCA reset_resume quirking

2018-02-25T20:07:10+00:00

Commit 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume fix
with a "rewritten" version") applied the USB_QUIRK_RESET_RESUME to all QCA
USB Bluetooth modules. But it turns out that the resume problems are not
caused by the QCA Rome chipset, on most platforms it resumes fine. The
resume problems are actually a platform problem (likely the platform
cutting all power when suspended).

The USB_QUIRK_RESET_RESUME quirk also disables runtime suspend, so by
matching on usb-ids, we're causing all boards with these chips to use extra
power, to fix resume problems which only happen on some boards.

This commit fixes this by applying the quirk based on DMI matching instead
of on usb-ids, so that we match the platform and not the chipset.

Here is the /sys/kernel/debug/usb/devices for the Bluetooth module:

T:  Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#=  5 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e300 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Fixes: 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume..")
Cc: stable@vger.kernel.org
Cc: Brian Norris 
Cc: Kai-Heng Feng 
Reported-and-tested-by: Kevin Fenzi 
Signed-off-by: Hans de Goede 
Signed-off-by: Marcel Holtmann

vfs: do bulk POLL* -> EPOLL* replacement

2018-02-11T22:34:03+00:00

This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:

    for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
        L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
        for f in $L; do sed -i "-es/^\([^\"]*\)\(\\)/\\1E\\2/" $f; done
    done

with de-mangling cleanups yet to come.

NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do.  But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.

The next patch from Al will sort out the final differences, and we
should be all done.

Scripted-by: Al Viro 
Signed-off-by: Linus Torvalds

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

2018-01-31T22:31:10+00:00

Pull networking updates from David Miller:

 1) Significantly shrink the core networking routing structures. Result
    of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf

 2) Add netdevsim driver for testing various offloads, from Jakub
    Kicinski.

 3) Support cross-chip FDB operations in DSA, from Vivien Didelot.

 4) Add a 2nd listener hash table for TCP, similar to what was done for
    UDP. From Martin KaFai Lau.

 5) Add eBPF based queue selection to tun, from Jason Wang.

 6) Lockless qdisc support, from John Fastabend.

 7) SCTP stream interleave support, from Xin Long.

 8) Smoother TCP receive autotuning, from Eric Dumazet.

 9) Lots of erspan tunneling enhancements, from William Tu.

10) Add true function call support to BPF, from Alexei Starovoitov.

11) Add explicit support for GRO HW offloading, from Michael Chan.

12) Support extack generation in more netlink subsystems. From Alexander
    Aring, Quentin Monnet, and Jakub Kicinski.

13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
    Russell King.

14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.

15) Many improvements and simplifications to the NFP driver bpf JIT,
    from Jakub Kicinski.

16) Support for ipv6 non-equal cost multipath routing, from Ido
    Schimmel.

17) Add resource abstration to devlink, from Arkadi Sharshevsky.

18) Packet scheduler classifier shared filter block support, from Jiri
    Pirko.

19) Avoid locking in act_csum, from Davide Caratti.

20) devinet_ioctl() simplifications from Al viro.

21) More TCP bpf improvements from Lawrence Brakmo.

22) Add support for onlink ipv6 route flag, similar to ipv4, from David
    Ahern.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
  tls: Add support for encryption using async offload accelerator
  ip6mr: fix stale iterator
  net/sched: kconfig: Remove blank help texts
  openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
  tcp_nv: fix potential integer overflow in tcpnv_acked
  r8169: fix RTL8168EP take too long to complete driver initialization.
  qmi_wwan: Add support for Quectel EP06
  rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
  ipmr: Fix ptrdiff_t print formatting
  ibmvnic: Wait for device response when changing MAC
  qlcnic: fix deadlock bug
  tcp: release sk_frag.page in tcp_disconnect
  ipv4: Get the address of interface correctly.
  net_sched: gen_estimator: fix lockdep splat
  net: macb: Handle HRESP error
  net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
  ipv6: addrconf: break critical section in addrconf_verify_rtnl()
  ipv6: change route cache aging logic
  i40e/i40evf: Update DESC_NEEDED value to reflect larger value
  bnxt_en: cleanup DIM work on device shutdown
  ...

Bluetooth: btintel: Create common function for firmware download

2018-01-25T08:28:40+00:00

The firmware download flow for RAM SKU is same for both USB and UART
and this patch creates a common function for both driver.

Signed-off-by: Tedd Ho-Jeong An 
Signed-off-by: Marcel Holtmann