dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Use dmaenginem_async_device_register to simplify the code:
	remove dma_async_device_unregister.
	remove label unregister_slave, unregister_memcpy

Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

In the quest to remove all stack VLA usage from the kernel[1], this
switches to using a pre-allocated scratch register space, set up with
all other other allocations.

[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com

Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

There are no in kernel consumers for DMA_SG op. Removing operation,
dead code, and test code in dmatest.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Make these const as they are only used during a copy operation.
Done using Coccinelle.

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This dma engine driver directly accesses page_link assuming knowledge
that should be contained only in scatterlist.h.

We replace this access with a call to sg_chain which is equivalent.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Stephen Bates <sbates@raithlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Per Förlin <per.forlin@axis.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The ste_dma40 has burst level granularity on the residue
registers, which is necessary for some  clients to know,
notably the UART. Before this patch we get this message:

uart-pl011 80007000.uart: RX DMA disabled - no residue processing

This patch fixes it.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Since the introduction of the .directions flags, ste_dma40 was
never patched to indicate which transfer directions it can manage.
This causes a problem when trying to use the dmaengine for generic
ALSA SoC DMA:

ux500-msp-i2s.1: Failed to get DMA channel capabilities, falling
   back to period counting: -6

This patch fixes this issue by indicating the supported transfer
directions for slave and memcpy channels.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>