linux-toradex.git/drivers/extcon, branch v5.1-rc4 Linux kernel for Apalis and Colibri modules extcon: ptn5150: Fix return value check in ptn5150_i2c_probe() 2019-02-11T08:21:38+00:00 Wei Yongjun weiyongjun1@huawei.com 2019-01-25T01:45:54+00:00 3dfed89512d3b65f6f092cfaaee53b0698bbf75e In case of error, the function devm_gpiod_get() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> 
In case of error, the function devm_gpiod_get() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
extcon: Add support for ptn5150 extcon driver 2019-02-11T08:21:38+00:00 Vijai Kumar K vijaikumar.kanagarajan@gmail.com 2019-01-23T12:46:56+00:00 4ed754de2d66084d4a7785f565d7c42ad89a3ea9 PTN5150 is a small thin low power CC (Configurationn Channel) Logic chip supporting the USB Type-C connector application with CC control logic detection and indication functions. Signed-off-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com> [cw00.choi: Fix bulid dependency and clean-up code] Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> 
PTN5150 is a small thin low power CC (Configurationn Channel)
Logic chip supporting the USB Type-C connector application with
CC control logic detection and indication functions.

Signed-off-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
[cw00.choi: Fix bulid dependency and clean-up code]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
extcon: max8997: Fix lack of path setting in USB device mode 2018-11-14T00:06:32+00:00 Marek Szyprowski m.szyprowski@samsung.com 2018-11-13T15:38:47+00:00 a2dc50914744eea9f83a70a5db0486be625e5dc0 MAX8997 driver disables automatic path selection from MicroUSB connector and manually sets path to either UART or USB lines. However the code for setting USB path worked only for USB host mode (when ID pin is set to ground). When standard USB cable (USB device mode) is connected, path registers are not touched. This means that once the non-USB accessory is connected to MAX8997-operated micro USB port, the path is no longer set to USB and USB device mode doesn't work. This patch fixes it by setting USB path both for USB and USB host modes. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> 
MAX8997 driver disables automatic path selection from MicroUSB connector
and manually sets path to either UART or USB lines. However the code for
setting USB path worked only for USB host mode (when ID pin is set
to ground). When standard USB cable (USB device mode) is connected, path
registers are not touched. This means that once the non-USB accessory is
connected to MAX8997-operated micro USB port, the path is no longer set
to USB and USB device mode doesn't work. This patch fixes it by setting
USB path both for USB and USB host modes.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
extcon: max8997: Avoid forcing UART path on drive probe 2018-11-12T00:17:13+00:00 Marek Szyprowski m.szyprowski@samsung.com 2018-11-08T13:45:48+00:00 3e34c819896091d0f1bbf6ece8a620552f8dc04e Driver unconditionally forces UART path during probe, probably to ensure that one can get kernel serial log as soon as possible. This approach causes some issues, especially when board is booted with non-UART cable connected to micro-USB port. For example, when USB cable is connected, UART TX/RX lines are unconditionally short-circuited to USB D+/D- lines. This is in turn recognized by a series of serial BREAK signals and some random characters when USB host tries to perform enumeration procedure. To solve the above issue and keep UART console operational as early as possible, set UART path only when USB ID reports UART capable cable. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> 
Driver unconditionally forces UART path during probe, probably to ensure
that one can get kernel serial log as soon as possible.

This approach causes some issues, especially when board is booted with
non-UART cable connected to micro-USB port. For example, when USB cable is
connected, UART TX/RX lines are unconditionally short-circuited to USB
D+/D- lines. This is in turn recognized by a series of serial BREAK
signals and some random characters when USB host tries to perform
enumeration procedure.

To solve the above issue and keep UART console operational as early as
possible, set UART path only when USB ID reports UART capable cable.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
extcon: max14577: Avoid forcing UART path on drive probe 2018-11-12T00:17:13+00:00 Marek Szyprowski m.szyprowski@samsung.com 2018-11-08T13:45:47+00:00 5a196c29bb27d606c4bd82f6893462a39766ff7a Driver unconditionally forces UART path during probe, probably to ensure that one can get kernel serial log as soon as possible. This approach causes some issues, especially when board is booted with non-UART cable connected to micro-USB port. For example, when USB cable is connected, UART TX/RX lines are unconditionally short-circuited to USB D+/D- lines. This is in turn recognized by a series of serial BREAK signals and some random characters when USB host tries to perform enumeration procedure. To solve the above issue and keep UART console operational as early as possible, set UART path only when USB ID reports UART capable cable. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> 
Driver unconditionally forces UART path during probe, probably to ensure
that one can get kernel serial log as soon as possible.

This approach causes some issues, especially when board is booted with
non-UART cable connected to micro-USB port. For example, when USB cable is
connected, UART TX/RX lines are unconditionally short-circuited to USB
D+/D- lines. This is in turn recognized by a series of serial BREAK
signals and some random characters when USB host tries to perform
enumeration procedure.

To solve the above issue and keep UART console operational as early as
possible, set UART path only when USB ID reports UART capable cable.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
extcon: max77693: Avoid forcing UART path on drive probe 2018-11-12T00:17:13+00:00 Marek Szyprowski m.szyprowski@samsung.com 2018-11-08T13:45:46+00:00 6865f2ef9d6576508498fe6127d252b22a70ab39 Driver unconditionally forces UART path during probe, probably to ensure that one can get kernel serial log as soon as possible. This approach causes some issues, especially when board is booted with non-UART cable connected to micro-USB port. For example, when USB cable is connected, UART TX/RX lines are unconditionally short-circuited to USB D+/D- lines. This is in turn recognized by a series of serial BREAK signals and some random characters when USB host tries to perform enumeration procedure. To solve the above issue and keep UART console operational as early as possible, set UART path only when USB ID reports UART capable cable. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> 
Driver unconditionally forces UART path during probe, probably to ensure
that one can get kernel serial log as soon as possible.

This approach causes some issues, especially when board is booted with
non-UART cable connected to micro-USB port. For example, when USB cable is
connected, UART TX/RX lines are unconditionally short-circuited to USB
D+/D- lines. This is in turn recognized by a series of serial BREAK
signals and some random characters when USB host tries to perform
enumeration procedure.

To solve the above issue and keep UART console operational as early as
possible, set UART path only when USB ID reports UART capable cable.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
extcon: max77843: Avoid forcing UART path on drive probe 2018-11-12T00:17:13+00:00 Marek Szyprowski m.szyprowski@samsung.com 2018-11-08T13:45:45+00:00 d9204acb37569579fc49af1689c0ae32bdd4710f Driver unconditionally forces UART path during probe, probably to ensure that one can get kernel serial log as soon as possible. This approach causes some issues, especially when board is booted with non-UART cable connected to micro-USB port. For example, when USB cable is connected, UART TX/RX lines are unconditionally short-circuited to USB D+/D- lines. This is in turn recognized by a series of serial BREAK signals and some random characters when USB host tries to perform enumeration procedure. To solve the above issue and keep UART console operational as early as possible, set UART path only when USB ID reports UART capable cable. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> 
Driver unconditionally forces UART path during probe, probably to ensure
that one can get kernel serial log as soon as possible.

This approach causes some issues, especially when board is booted with
non-UART cable connected to micro-USB port. For example, when USB cable is
connected, UART TX/RX lines are unconditionally short-circuited to USB
D+/D- lines. This is in turn recognized by a series of serial BREAK
signals and some random characters when USB host tries to perform
enumeration procedure.

To solve the above issue and keep UART console operational as early as
possible, set UART path only when USB ID reports UART capable cable.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
extcon: int3496: Convert to use SPDX identifier 2018-08-28T02:21:15+00:00 Andy Shevchenko andriy.shevchenko@linux.intel.com 2018-08-27T15:35:57+00:00 2e464ff0a9b1ab0fbb56e2ca8b1f5ff8c9f4e02f Convert driver to use SPDX identifier. While here, fix MODULE_LICENSE() string to be the same as license text states. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> 
Convert driver to use SPDX identifier.

While here, fix MODULE_LICENSE() string to be the same as license text states.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
extcon: cht-wc: Convert to use SPDX identifier 2018-08-28T02:21:15+00:00 Andy Shevchenko andriy.shevchenko@linux.intel.com 2018-08-27T15:35:56+00:00 900ed55571941c5b61869954dc96e082e2ded78d Convert driver to use SPDX identifier. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> 
Convert driver to use SPDX identifier.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
extcon: cht-wc: Correct USBID bit field handling 2018-08-28T02:21:15+00:00 Andy Shevchenko andriy.shevchenko@linux.intel.com 2018-08-27T15:35:55+00:00 a4722503fadf0ed6219153da7ed6fa6cb4da98ec USBID is 2-bit bit field according to specification. Make it clear. No functional change intended. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> 
USBID is 2-bit bit field according to specification. Make it clear.

No functional change intended.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>