Conflicts:
	drivers/firewire/core-card.c
	drivers/firewire/core-cdev.c

and forgotten #include <linux/time.h> in drivers/firewire/ohci.c

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

There is an at least theoretic race condition in which .start_iso etc.
could still be called between when the dummy driver is bound to the card
and when the children devices are being shut down.  Add dummy_start_iso
and friends.

On the other hand, .enable, .set_config_rom, .read_csr, write_csr do not
need to be implemented by the dummy driver, as commented.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Add an FW_CDEV_IOC_RECEIVE_PHY_PACKETS ioctl() and
FW_CDEV_EVENT_PHY_PACKET_RECEIVED poll()/read() event for /dev/fw*.
This can be used to get information from remote PHYs by remote access
PHY packets.

This is also the 2nd half of the functionality (the receive part) to
support a userspace implementation of a VersaPHY transaction layer.

Safety considerations:

  - PHY packets are generally broadcasts, hence some kind of elevated
    privileges should be required of a process to be able to listen in
    on PHY packets.  This implementation assumes that a process that is
    allowed to open the /dev/fw* of a local node does have this
    privilege.

    There was an inconclusive discussion about introducing POSIX
    capabilities as a means to check for user privileges for these
    kinds of operations.

Other limitations:

  - PHY packet reception may be switched on by ioctl() but cannot be
    switched off again.  It would be trivial to provide an off switch,
    but this is not worth the code.  The client should simply close()
    the fd then, or just ignore further events.

  - For sake of simplicity of API and kernel-side implementation, no
    filter per packet content is provided.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

core-transaction.c transmit_complete_callback() and close_transaction()
expect packet callback status to be an ACK or RCODE, and ACKs get
translated to RCODEs for transaction callbacks.

An old comment on the packet callback API (been there from the initial
submission of the stack) and the dummy_driver implementation of
send_request/send_response deviated from this as they also included
-ERRNO in the range of status values.

Let's narrow status values down to ACK and RCODE to prevent surprises.
RCODE_CANCELLED is chosen as the dummy_driver's RCODE as its meaning of
"transaction timed out" comes closest to what happens when a transaction
coincides with card removal.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Bus resets which are triggered
  - by the kernel drivers after updates of the local nodes' config ROM,
  - by userspace software via ioctl
shall be deferred until after >=2 seconds after the last bus reset.

If multiple modifications of the local nodes' config ROM happen in a row,
only a single bus reset should happen after them.

When the local node's link goes from inactive to active or vice versa,
and at the two occasions of bus resets mentioned above --- and if the
current gap count differs from 63 --- the bus reset should be preceded
by a PHY configuration packet that reaffirms the gap count.  Otherwise a
bus manager would have to reset the bus again right after that.

This is necessary to promote bus stability, e.g. leave grace periods for
allocations and reallocations of isochronous channels and bandwidth,
SBP-2 reconnections etc.; see IEEE 1394 clause 8.2.1.

This change implements all of the above by moving bus reset initiation
into a delayed work (except for bus resets which are triggered by the
bus manager workqueue job and are performed there immediately).  It
comes with a necessary addition to the card driver methods that allows
to get the current gap count from PHY registers.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Fix an obscure ABI feature that is a bit of a hassle to implement.
However, somebody put it into the ABI, so let's fill in a sensible
value there.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This is a workqueue job and always entered with IRQs enabled.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

In case of fw_card_bm_work()'s lock request, the present sizeof
expression is going to be wrong if somebody changes the fw_card's DMA
scratch buffer's size in the future.

In case of quadlet write requests, sizeof(u32) is just silly; it's 4.

In case of SBP-2 ORB pointer write requests, 8 is arguably quicker to
understand as the correct and only possible value than
sizeof(some_datum).

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

As part of the bus manager responsibilities, make sure that the cycle
master sends cycle start packets.  This is needed when the old bus
manager disabled the cycle master's cmstr bit and there are iso-capable
nodes on the new bus.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>

On OHCI 1.1 controllers, let the hardware allocate the broadcast channel
automatically.  This removes a theoretical race condition directly after
a bus reset where it could be possible to read the channel allocation
register with channel 31 still being unallocated.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>