Reported by Jay Fenlason:  ioctl() did not return as intended
  - the size of data read into ioctl_send_request,
  - the number of datagrams enqueued by ioctl_queue_iso.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Reported by Jay Fenlason:
The iso packet control accessors in fw-cdev.c had bogus masks.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

queuecommand() looked at the remote and local node IDs before it read
the bus generation.  The corresponding race with sbp2_reconnect updating
these data was probably impossible to happen though because the current
code blocks the SCSI layer during reconnection.  However, better safe
than sorry, especially if someone later improves the code to not block
the SCSI layer.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

1. We don't need to round the SBP-2 segment size limit down to a
   multiple of 4 kB (0xffff -> 0xf000).  It is only necessary to
   ensure quadlet alignment (0xffff -> 0xfffc).

2. Use dma_set_max_seg_size() to tell the DMA mapping infrastructure
   and the block IO layer about the restriction.  This way we can
   remove the size checks and segment splitting in the queuecommand
   path.

   This assumes that no other code in the firewire stack uses
   dma_map_sg() with conflicting requirements.  It furthermore assumes
   that the controller device's platform actually allows us to set the
   segment size to our liking.  Assert the latter with a BUG_ON().

3. Also use blk_queue_max_segment_size() to tell the block IO layer
   about it.  It cannot know it because our scsi_add_host() does not
   point to the FireWire controller's device.

Thanks to Grant Grundler and FUJITA Tomonori for advice.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Share code between fw_send_request + wait_for_completion callers.

Signed-off-by: Jay Fenlason <fenlason@redhat.com>

Addendum:
Removes an unnecessary struct and an ununsed retry loop.
Calls it fw_run_transaction() instead of fw_send_request_sync().

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: Preserve response data alignment bug when it is harmless

Recently, a bug having to do with the alignment of transaction response
data was fixed.  However, some apps such as libdc1394 relied on the
presence of that bug in order to function correctly.  In order to stay
compatible with old versions of those apps, this patch preserves the bug
in cases where it is harmless to normal operation (such as the single
quadlet read) due to a simple duplication of data.  This guarantees
maximum compatability for those users who are using the old app with the
fixed kernel.

Signed-off-by: David Moore <dcm@acm.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: state userland requirements in Kconfig help
  firewire: avoid memleak after phy config transmit failure
  firewire: fw-ohci: TSB43AB22/A dualbuffer workaround
  firewire: queue the right number of data
  firewire: warn on unfinished transactions during card removal
  firewire: small fw_fill_request cleanup
  firewire: fully initialize fw_transaction before marking it pending
  firewire: fix race of bus reset with request transmission

Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:

This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).

I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread).  So I
CC'ed this to KVM camp.  Comments are appreciated.

A pointer to dma_mapping_ops to struct dev_archdata is added.  If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it.  If it's
NULL, the system-wide dma_ops pointer is used as before.

If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging).  It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.

The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations.  So x86 can't have dma_mapping_ops per
device.  Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.

The first patch adds the device argument to dma_mapping_error.  The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.

This patch:

dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations.  So we can't have dma_mapping_ops per device.

Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function.  x86 IOMMUs use device
argument.

[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>