Pull ARM driver updates from Olof Johansson:
 "Updates of SoC-near drivers and other driver updates that makes more
  sense to take through our tree.

  The largest part of this is a conversion of device registration for
  some renesas shmobile/sh devices over to use resources.  This has
  required coordination with the corresponding arch/sh changes, and
  we've agreed to merge the arch/sh changes through our tree.

  Added in this branch is support for Trusted Foundations secure
  firmware, which is what is used on many of the commercial Nvidia Tegra
  products that are in the market, including the Nvidia Shield.  The
  code is local to arch/arm at this time since it's uncertain whether it
  will be shared with arm64 longer-term, if needed we will refactor
  later.

  A couple of new RTC drivers used on ARM boards, merged through our
  tree on request by the RTC maintainer.

  ... plus a bunch of smaller updates across the board, gpio conversions
  for davinci, etc"

* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
  watchdog: davinci: rename platform driver to davinci-wdt
  tty: serial: Limit msm_serial_hs driver to platforms that use it
  mmc: msm_sdcc: Limit driver to platforms that use it
  usb: phy: msm: Move mach dependent code to platform data
  clk: versatile: fixup IM-PD1 clock implementation
  clk: versatile: pass a name to ICST clock provider
  ARM: integrator: pass parent IRQ to the SIC
  irqchip: versatile FPGA: support cascaded interrupts from DT
  gpio: davinci: don't create irq_domain in case of unbanked irqs
  gpio: davinci: use chained_irq_enter/chained_irq_exit API
  gpio: davinci: add OF support
  gpio: davinci: remove unused variable intc_irq_num
  gpio: davinci: convert to use irqdomain support.
  gpio: introduce GPIO_DAVINCI kconfig option
  gpio: davinci: get rid of DAVINCI_N_GPIO
  gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
  serial: sh-sci: Add OF support
  serial: sh-sci: Add device tree bindings documentation
  serial: sh-sci: Remove platform data mapbase and irqs fields
  serial: sh-sci: Remove platform data scbrr_algo_id field
  ...

Pull MFD changes from Lee Jones:
 "New drivers
   - Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
     Battery Charger
   - TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
     Generator

  Existing driver adaptions
   - Expansion of Wolfson Arizona DSP and High-Pass filter controls
   - TI TWL6040 default Regmap support and Regcache addition/bypass
   - Some nice Smatch catch fixes
   - Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
   - ChromeOS EC timing (delay) adaptions and added dependency on OF
   - Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
   - Watchdog support added for NVIDIA AS3722
   - Convert functions to static in TI AM335x
   - Realigned previously defeated functionality in TI AM335x
   - IIO ADC-TSC concurrency dead-lock/timeout resolution
   - Addition of Power Management and Clock support for Samsung core
   - DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
   - Greater use of irqdomain functionality in ST-E AB8500
   - Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
   - Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
   - Device Tree documentation added for TI/Nat Semi LP3943
   - Version detection and voltage tables for TI TPS6586x PMIC devices
   - Simplification of Freescale MC13XXX (de-)initialisation routines
   - Clean-up and simplification of the Realtek parent driver
   - Added support for RTL8402 Realtek PCI-Express card reader
   - Resource leak fix for Maxim 77686
   - Possible suspend BUG() fix in OMAP USB TLL
   - Support for new Wolfson WM5110 Revision (D)
   - Testing of automatic assignment of of_node in mfd_add_device()
   - Reversion of the above when it started to cause issues
   - Remove legacy Platform Data from;
              TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
   - Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
              removal, unused uninitialised warning mitigation, error
              message clarity, removal of redundant/duplicate checks,
              licensing (GPL -> GPL2), coding consistency, duplicate
              function declaration, ret checks, commit corrections,
              redundant of_match_ptr() helper removal, spelling,
              #if-deffery removal and header guards name changes"

* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
  mfd: wm5110: Add register patch for rev D chip
  mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
  gpio: lp3943: Remove redundant of_match_ptr helper
  mfd: sta2x11-mfd: Use named constants for pci_power_t values
  Documentation: mfd: Fix LDO index in s2mps11.txt
  mfd: Cleanup mfd-mcp-sa11x0.h header
  mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
  mfd: twl6030: Fix endianness problem in IRQ handler
  mfd: sec-core: Add cells for S5M8767-clocks
  mfd: max14577: Remove redundant of_match_ptr helper
  mfd: twl6040: Fix sparse non static symbol warning
  mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
  mfd: rtsx: Fix sparse non static symbol warning
  mfd: max77693: Set proper maximum register for MUIC regmap
  mfd: max77686: Fix regmap resource leak on driver remove
  mfd: Represent correct filenames in file headers
  mfd: rtsx: Add support for card reader rtl8402
  mfd: rtsx: Add set pull control macro and simplify rtl8411
  mfd: max8997: Enforce mfd_add_devices() return value check
  mfd: mc13xxx: Simplify probe() & remove()
  ...

This is one of LP3943 MFD driver.
LP3943 is configurable as a GPIO expander, up to 16 GPIOs.

* Application note: how to configure LP3943 as a GPIO expander
  http://www.ti.com/lit/an/snva287a/snva287a.pdf

* Supported GPIO controller operations
  request, free, direction_input, direction_output, get and set

* GPIO direction register not supported
  LP3943 doesn't have the GPIO direction register. It only provides input and
  output status registers.
  So, private data for the direction should be handled manually.
  This variable is updated whenever the direction is changed and
  used in 'get' operation.

* Pin assignment
  A driver data, 'pin_used' is checked when a GPIO is requested.
  If the GPIO is already assigned, then returns as failure.
  If the GPIO is available, 'pin_used' is set.
  When the GPIO is not used anymore, then it is cleared.
  It is defined as unsigned long type for atomic bit operation APIs,
  but only LSB 16bits are used because LP3943 has 16 outputs.

Signed-off-by: Milo Kim <milo.kim@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The compatible to Davinci GPIO HW block is used by other TI SoCs, like
Keystone, where GPIO support is declared as optional.

Hence, introduce GPIO_DAVINCI Kconfig option which will allow to enable
Davinci GPIO driver for Keystone SoCs when needed. At same time, kept
Davinci GPIO driver enabled for Davinci SoCs by default.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

This patch adds support for the GPIOs found on the SMSC "Super I/
SCH311x.

The chip detection and I/O functions are copied from sch311x_wdt.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

GPIO32 is a standard optional extension to the Xtensa architecture
core that provides preconfigured output and input ports for intra
SoC signaling. The GPIO32 option is implemented as 32bit Tensilica
Instruction Extension (TIE) output state called EXPSTATE, and 32bit
input wire called IMPWIRE. This driver treats input and output
states as two distinct devices.

v3:
* Use BUG() in xtensa_impwire_set_value() to indicate that
  it should never be called (Linus Walleij)
v2:
* Address the comments of Linus Walleij:
  - Add a few comments
  - Expand commit log message
  - Use the BIT() macro for bit offsets
  - Rewrite CPENABLE handling as static inlines
  - Use device_initcall()
* Depend on !SMP for reason explained in the comments (Marc Gauthier)
* Use XCHAL_CP_ID_XTIOP to enable/disable GPIO32 only

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add GPIO driver for MOXA ART SoCs.

Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull GPIO changes from Linus Walleij:
 "Here is the bulk of GPIO changes for the v3.13 development cycle.

  I've got ACKs for the things that affect other subsystems (or it's my
  own subsystem, like pinctrl).  Most of that pertain to an attempt from
  my side to consolidate and get rid of custom GPIO implementations in
  the ARM tree.  I will continue doing this.

  The main change this time is the new GPIO descriptor API, background
  for this can be found in Corbet's summary from this january in LWN:

    http://lwn.net/Articles/533632/

  Summary:

   - Merged the GPIO descriptor API from Alexandre Courbot.  This is a
     first step toward trying to get rid of the global GPIO numberspace
     for the future.

   - Add an API so that driver can flag that a certain GPIO line is
     being used by a irqchip backend for generating IRQs, so that we can
     enforce checks, like not allowing users to switch that line to an
     output at runtime, since this makes no sense.  Implemented
     corresponding calls in a few select drivers.

   - ACPI GPIO cleanups, refactorings and switch to using the
     descriptor-based interface.

   - Support for the TPS80036 Palmas GPIO variant.

   - A new driver for the Broadcom Kona GPIO SoC IP block.

   - Device tree support for the PCF857x driver.

   - A set of ARM GPIO refactorings with the goal of getting rid of a
     bunch of custom GPIO implementations from the arch/arm/* tree:

     * Move the IOP GPIO driver to the GPIO subsystem and fix all users
       to use the gpiolib API for accessing GPIOs.  Delete the old
       custom GPIO implementation.

     * Delete the unused custom PXA GPIO implemention.

     * Convert all users of the IXP4 custom GPIO implementation to use
       gpiolib and delete the custom implementation.

     * Delete the custom Gemini GPIO implementation, also completely
       unused.

   - Various cleanups and renamings"

* tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
  gpio: gpio-mxs: Remove unneeded dt checks
  gpio: pl061: don't depend on CONFIG_ARM
  gpio: bcm-kona: add missing .owner to struct gpio_chip
  gpiolib: provide a declaration of seq_file in gpio/driver.h
  gpiolib: include gpio/consumer.h in of_gpio.h for desc_to_gpio()
  gpio: provide stubs for devres gpio functions
  gpiolib: devres: add missing headers
  gpiolib: make GPIO_DEVRES depend on GPIOLIB
  gpiolib: devres: fix devm_gpiod_get_index()
  gpiolib / ACPI: document the GPIO descriptor based interface
  gpiolib / ACPI: allow passing GPIOF_ACTIVE_LOW for GpioInt resources
  gpiolib / ACPI: add ACPI support for gpiod_get_index()
  gpiolib / ACPI: convert to gpiod interfaces
  gpiolib: add gpiod_get() and gpiod_put() functions
  gpiolib: port of_ functions to use gpiod
  gpiolib: export descriptor-based GPIO interface
  Fixup "MAINTAINERS: GPIO-INTEL-MID: add maintainer"
  gpio: bcm281xx: Don't print addresses of GPIO area in probe()
  gpio: tegra: use new gpio_lock_as_irq() API
  gpio: rcar: Include linux/of.h header
  ...

The GPIO driver for the Abilis Systems TB10x series of SOCs based on ARC700
CPUs. It supports GPIO control and GPIO interrupt generation. This driver
works in conjunction with the TB10x pinctrl driver.

Signed-off-by: Sascha Leuenberger <sascha.leuenberger@abilis.com>
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpio-langwell is a deprecated name. Despite the driver was made
initially for Langwell, it supports now other Intel Mid SoC's.

This patch does no change beside the file renaming with Kconfig/Makefile
update.

Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>