drm/panel: Changes for v4.6-rc1 This contains a refactoring of parts of the DSI core to allow creating DSI devices from non-DSI control busses (i.e. I2C, SPI, ...). Other than that there's support for a couple of new panels as well as a few cleanup patches. * tag 'drm/panel/for-4.6-rc1' of http://anongit.freedesktop.org/git/tegra/linux: drm/bridge: Make (pre/post) enable/disable callbacks optional drm/panel: simple: Add URT UMSH-8596MD-xT panels support dt-bindings: Add URT UMSH-8596MD-xT panel bindings of: Add United Radiant Technology Corporation vendor prefix drm/panel: simple: Support for LG lp120up1 panel dt-bindings: Add LG lp120up1 panel bindings drm/panel: simple: Fix g121x1_l03 hsync/vsync polarity drm/dsi: Get DSI host by DT device node drm/dsi: Add routine to unregister a DSI device drm/dsi: Try to match non-DT DSI devices drm/dsi: Use mipi_dsi_device_register_full() for DSI device creation drm/dsi: Check for CONFIG_OF when defining of_mipi_dsi_device_add()
Add support for United Radiant Technology UMSH-8596MD-xT 7.0" WVGA TFT LCD panels in the simple-panel driver. Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG lp120up1 TFT LCD panel with eDP interface is a 12.0" 1920x1280 panel, which can be supported by the simple panel driver. Signed-off-by: Jitao Shi <jitao.shi@mediatek.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Set hsync/vsync to active low for g121x1_l03 panel to match the recommended setting in the datasheet. Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
The current default configuration is as follows: - Invert VSYNC signal (active LOW) - Invert HSYNC signal (active LOW) The mode flags allow to specify the required polarity per mode. Furthermore, none of the current driver settings is actually a standard polarity. This patch applies the current driver default polarities as explicit flags to the display which has been introduced with the driver (NEC WQVGA "nec,nl4827hc19-05b"). The driver now also parses the flags field and applies the configuration accordingly, by using the following values as standard polarities: (e.g. when no flags are specified): - VSYNC signal not inverted (active HIGH) - HSYNC signal not inverted (active HIGH) Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stefan Agner <stefan@agner.ch>
The QiaoDian Xianshi QD43003C0-40 is a 4"3 TFT LCD panel. Timings from the OTA5180A document, ver 0.9, section 10.1.1: http://www.orientdisplay.com/pdf/OTA5180A.pdf Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Document that 'width' and 'height' are measured in millimeters. Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
The Kyocera TCG121XGLP panel is an XGA LCD TFT panel connected through LVDS, which can be supported by the simple panel driver. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sharp LS043T1LE01 is a 4.3", 540x960 TFT-LCD panel connected using two DSI lanes. It is for example found on the Qualcomm Snapdragon 800 Dragonboard (APQ8074). Signed-off-by: Werner Johansson <werner.johansson@sonymobile.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Reviewed-by: Archit Taneja <architt@codeaurora.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the Panasonic panel found in some Xperia Z2 tablets. Signed-off-by: Werner Johansson <werner.johansson@sonymobile.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Thierry Reding <treding@nvidia.com>