Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>

When writeback is enabled, the GPU shadows writes to certain
registers into a buffer in memory.  The driver can then read
the values from the shadow rather than reading back from the
register across the bus.  Writeback can be disabled by setting
the no_wb module param to 1.

On r6xx/r7xx/evergreen, the following registers are shadowed:
- CP scratch registers
- CP read pointer
- IH write pointer
On r1xx-rr5xx, the following registers are shadowed:
- CP scratch registers
- CP read pointer

v2:
- Combine wb patches for r6xx-evergreen and r1xx-r5xx
- Writeback is disabled on AGP boards since it tends to be
unreliable on AGP using the gart.
- Check radeon_wb_init return values properly.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

On systems using kexec, the new kernel is booted straight from the old kernel, without any warning to the graphics driver. So the GPU is basically left as-is in a running state, however the CPU side is completly reset.

Without stating the saneness of anyone using kexec on live systems, we should at least try not to crash the GPU. This patch resets 3 registers to 0 that could cause bad things to happen to the running system.

This allows kexec to work on a Power6/RN50 system.

Signed-off-by: Dave Airlie <airlied@redhat.com>

This adds an additional profile, mid, to the pm profile
code which takes the place of the old low profile.  The default
behavior remains the same, e.g., auto profile now selects between
mid and high profiles based on power source, however, you can now
manually force the low profile which was previously only available
as a dpms off state.  Enabling the low profile when the displays
are on has been known to cause display corruption in some cases.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

* anholt/drm-intel-next: (515 commits)
  drm/i915: Fix out of tree builds
  drm/i915: move fence lru to struct drm_i915_fence_reg
  drm/i915: don't allow tiling changes on pinned buffers v2
  drm/i915: Be extra careful about A/D matching for multifunction SDVO
  drm/i915: Fix DDC bus selection for multifunction SDVO
  drm/i915: cleanup mode setting before unmapping registers
  drm/i915: Make fbc control wrapper functions
  drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
  drm/i915: Use spatio-temporal dithering on PCH
  [MTD] Remove zero-length files mtdbdi.c and internal.ho
  pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
  libata: Fix several inaccuracies in developer's guide
  slub: Fix bad boundary check in init_kmem_cache_nodes()
  raid6: fix recovery performance regression
  KEYS: call_sbin_request_key() must write lock keyrings before modifying them
  KEYS: Use RCU dereference wrappers in keyring key type code
  KEYS: find_keyring_by_name() can gain access to a freed keyring
  ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
  ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
  ALSA: take tu->qlock with irqs disabled
  ...

- Separate dynpm and profile based power management methods.  You can select the pm method
  by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
  "default" - default clocks
  "auto" - select between low and high based on ac/dc state
  "low" - DC, low power mode
  "high" - AC, performance mode
  The current base profile is "default", but it should switched to "auto" once we've tested
  on more systems.  Switching the state is a matter of echoing the requested profile to
  power_profile in sysfs.  The lowest power states are selected automatically when dpms turns
  the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment.  We can revisit this later once we
  have basic pm in.
- Move pm init/fini to modesetting path.  pm is tightly coupled with display state.  Make sure
  display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option.  It's now selectable via sysfs.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Conflicts:
	drivers/gpu/drm/i915/i915_dma.c
	drivers/gpu/drm/i915/i915_drv.h
	drivers/gpu/drm/radeon/r300.c

The BSD ringbuffer support that is landing in this branch
significantly conflicts with the Ironlake PIPE_CONTROL fix on master,
and requires it to be tested successfully anyway.

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon: Fix sparc regression in r300_scratch()
  drm: make sure vblank interrupts are disabled at DPMS time
  drm/radeon/kms/evergreen: No EnableYUV table
  drm/radeon: 9800 SE has only one quadpipe
  drm/radeon/kms: don't print error for legal crtcs.
  drm/radeon/kms/evergreen: fix LUT setup

Although these cards have 2 pipelines on the silicon only
the first passed the QA and the other should be disabled.

http://www.digital-daily.com/video/ati-radeon9800se/
http://www.rojakpot.com/showarticle.aspx?artno=101&pgno=1

agd5f: add some other SE cards as well; fix up kms

Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>