Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>

When writeback is enabled, the GPU shadows writes to certain
registers into a buffer in memory.  The driver can then read
the values from the shadow rather than reading back from the
register across the bus.  Writeback can be disabled by setting
the no_wb module param to 1.

On r6xx/r7xx/evergreen, the following registers are shadowed:
- CP scratch registers
- CP read pointer
- IH write pointer
On r1xx-rr5xx, the following registers are shadowed:
- CP scratch registers
- CP read pointer

v2:
- Combine wb patches for r6xx-evergreen and r1xx-r5xx
- Writeback is disabled on AGP boards since it tends to be
unreliable on AGP using the gart.
- Check radeon_wb_init return values properly.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Need this to avoid conflicts with future radeon fixes

On systems using kexec, the new kernel is booted straight from the old kernel, without any warning to the graphics driver. So the GPU is basically left as-is in a running state, however the CPU side is completly reset.

Without stating the saneness of anyone using kexec on live systems, we should at least try not to crash the GPU. This patch resets 3 registers to 0 that could cause bad things to happen to the running system.

This allows kexec to work on a Power6/RN50 system.

Signed-off-by: Dave Airlie <airlied@redhat.com>

The asics in question have the following requirements with regard to
their gart setups:

1. The GART aperture size has to be in the form of 2^X bytes, where X is from 25 to 31
2. The GART aperture MC base has to be aligned to a boundary equal to the size of the
aperture.
3. The GART page table has to be aligned to the boundary equal to the size of the table.
4. The GART page table size is: table_entry_size * (aperture_size / page_size)
5. The GART page table has to be allocated in non-paged, non-cached, contiguous system
memory.

This patch takes care 2.  The rest should already be handled properly.

This fixes a regression noticed by: Torsten Kaiser <just.for.lkml@googlemail.com>

Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

- Separate dynpm and profile based power management methods.  You can select the pm method
  by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
  "default" - default clocks
  "auto" - select between low and high based on ac/dc state
  "low" - DC, low power mode
  "high" - AC, performance mode
  The current base profile is "default", but it should switched to "auto" once we've tested
  on more systems.  Switching the state is a matter of echoing the requested profile to
  power_profile in sysfs.  The lowest power states are selected automatically when dpms turns
  the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment.  We can revisit this later once we
  have basic pm in.
- Move pm init/fini to modesetting path.  pm is tightly coupled with display state.  Make sure
  display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option.  It's now selectable via sysfs.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This simplify and improve GPU reset for R1XX-R6XX hw, it's
not 100% reliable here are result:
- R1XX/R2XX works bunch of time in a row, sometimes it
  seems it can work indifinitly
- R3XX/R3XX the most unreliable one, sometimes you will be
  able to reset few times, sometimes not even once
- R5XX more reliable than previous hw, seems to work most
  of the times but once in a while it fails for no obvious
  reasons (same status than previous reset just no same
  happy ending)
- R6XX/R7XX are lot more reliable with this patch, still
  it seems that it can fail after a bunch (reset every
  2sec for 3hour bring down the GPU & computer)

This have been tested on various hw, for some odd reasons
i wasn't able to lockup RS480/RS690 (while they use to
love locking up).

Note that on R1XX-R5XX the cursor will disapear after
lockup haven't checked why, switch to console and back
to X will restore cursor.

Next step is to record the bogus command that leaded to
the lockup.

V2 Fix r6xx resume path to avoid reinitializing blit
module, use the gpu_lockup boolean to avoid entering
inifinite waiting loop on fence while reiniting the GPU

Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Patch rename gpu_reset to asic_reset in prevision of having
gpu_reset doing more stuff than just basic asic reset.

Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

- rs780/880 were using the wrong bandwidth functions
- convert r1xx-r4xx to use the same pm sclk/mclk structs as
r5xx+
- move bandwidth setup to a common function

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>