When initializing clocks, a reference to the TCON channel 0 clock is
obtained. However, the clock is never prepared and enabled later.
Switching from simplefb to DRM actually disables the clock (that was
usually configured by U-Boot) because of that.

On the V3s, this results in a hang when writing to some mixer registers
when switching over to DRM from simplefb.

Fix this by preparing and enabling the clock when initializing other
clocks. Waiting for sun4i_tcon_channel_enable to enable the clock is
apparently too late and results in the same mixer register access hang.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190131132550.26355-1-paul.kocialkowski@bootlin.com

Although TMDS clock is required for HDMI to properly function,
nobody called clk_prepare_enable(). This fixes reference counting
issues and makes sure clock is running when it needs to be running.

Due to TDMS clock being parent clock for DDC clock, TDMS clock
was turned on/off for each EDID probe, causing spurious failures
for certain HDMI/DVI screens.

Fixes: 9c5681011a0c ("drm/sun4i: Add HDMI support")
Signed-off-by: Priit Laes <priit.laes@paf.com>
[Maxime: Moved the TMDS clock enable earlier]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190122073232.7240-1-plaes@plaes.org

The device node iterators perform an of_node_get on each
iteration, so a jump out of the loop requires an of_node_put.

Remote and port also have augmented reference counts, so drop them
on each iteration and at the end of the function, respectively.
Remote is only used for the address it contains, not for the
contents of that address, so the reference count can be dropped
immediately.

The semantic patch that fixes the first part of this problem is
as follows (http://coccinelle.lip6.fr):

// <smpl>
@@
expression root,e;
local idexpression child;
iterator name for_each_child_of_node;
@@

 for_each_available_child_of_node(root, child) {
   ... when != of_node_put(child)
       when != e = child
+  of_node_put(child);
?  break;
   ...
}
... when != child
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1547369264-24831-5-git-send-email-Julia.Lawall@lip6.fr

H6 is first Allwinner SoC which supports 10 bit colors, HDR and AFBC.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-9-jernej.skrabec@siol.net

To prepare the introduction of tiled mode support, pass the framebuffer
format modifier to the helpers dealing with format support.

Since only linear mode is supported for now, add corresponding checks in
each helper.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-33-paul.kocialkowski@bootlin.com

This introduces support for the BGRX8888 output format for the frontend,
with its associated output format value definition.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-23-paul.kocialkowski@bootlin.com

Our hardware requires the pitch to be an even number when using YUV
formats with the frontend. Implement a driver-specific callback for GEM
dumb allocation that sets the pitch accordingly.

Since only the bpp is passed (and not the format), we cannot really
distinguish if this alignment is really required. Since it doesn't hurt
to align the pitch anyway, always do it.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-30-paul.kocialkowski@bootlin.com

The frontend comes with two "channels", that can be configured
independently. When used in YUV mode, the first channel (CH0) represents
the luminance component while the second channel (CH1) represents the
chrominance. In RGB mode, both have to be configured the same way.

Use variables (with the YUV terminology) for each channel's
dimensions, calculating the chroma dimensions from the luma dimensions
and the sub-sampling factors from the format description.

Since the configured size only has pixel precision, the fractional
fixed-point part of the source size is dropped for both components to
ensure that the scaling factors are accurate.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-26-paul.kocialkowski@bootlin.com

The values in the BT601 YUV to RGB colorspace translation are not
simply coded as multiples, but rather as fixed-point signed fractional
values on a given number of bits. Add an explanation about that.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-24-paul.kocialkowski@bootlin.com

This introduces support for the BGRX8888 input format for the frontend,
with its associated pixel sequence value definition. Other fields are
already configured correctly as they no longer depend on the format's
fourcc directly.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-22-paul.kocialkowski@bootlin.com