Cursors need to be in the GTT domain when being accessed by the GPU.
Previously this was a fortuitous byproduct of userspace using pwrite()
to upload the image data into the cursor. The redundant clflush was
removed in commit 9b8c4a and so the image was no longer being flushed
out of the caches into main memory. One could also devise a scenario
where the cursor was rendered by the GPU, prior to being attached as the
cursor, resulting in similar corruption due to the missing MI_FLUSH.

Fixes:

  Bug 28335 - Cursor corruption caused by commit 9b8c4a0b21
  https://bugs.freedesktop.org/show_bug.cgi?id=28335

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (41 commits)
  drm/radeon/kms: make sure display hw is disabled when suspending
  drm/vmwgfx: Allow userspace to change default layout. Bump minor.
  drm/vmwgfx: Fix framebuffer modesetting
  drm/vmwgfx: Fix vga save / restore with display topology.
  vgaarb: use MIT license
  vgaarb: convert pr_devel() to pr_debug()
  drm: fix typos in Linux DRM Developer's Guide
  drm/radeon/kms/pm: voltage fixes
  drm/radeon/kms/pm: radeon_set_power_state fixes
  drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
  drm/radeon/kms/pm: enable SetVoltage on r7xx/evergreen
  drm/radeon/kms/pm: add support for SetVoltage cmd table (V2)
  drm/radeon/kms/evergreen: add initial CS parser
  drm/kms: disable/enable poll around switcheroo on/off
  drm/nouveau: fixup confusion over which handle the DSM is hanging off.
  drm/nouveau: attempt to get bios from ACPI v3
  drm/nv50: cast IGP memory location to u64 before shifting
  drm/ttm: Fix ttm_page_alloc.c
  drm/ttm: Fix cached TTM page allocation.
  drm/vmwgfx: Remove some leftover debug messages.
  ...

Disable the display hw when suspending.
Should fix bug:
https://bugzilla.redhat.com/show_bug.cgi?id=522393

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The host may change the layout and, since the change is
communicated to the master, the master needs a way to
communicate the change to the kernel driver.

The minor version number is bumped to advertize the
availability of this feature.

Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Must set SVGA_NUM_REG_GUEST_DISPLAY before setting up the display information.

Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

vga save / restore previously didn't handle the display topology case.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

- Enable GPIO voltage for non pm modes as well so resetting
the default voltage works.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

- wait for vbl for both profile and dynpm
- unify profile and dynpm code paths more
- call pm_misc before of after clocks to make
sure voltage is changed in the proper order.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The default power state does not always match the default clocks and voltage
for a particular card.  The information in the firmware info table is correct
and should be used in preference to the info the default power state.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

I missed these in the r6xx commit.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>