Merge mag3110 drivers from sensor team.
The drivers are updated with chip position configure
in driver, export set delay interface to userspace and
use polling mode instead of interrupt mode.

Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>

- Added V3P3 regulator to max17135
- Added calls to enable/disable V3P3 regulator from EPDC driver
- Improved Kconfig detail for max17135 MFD and HWMON entries

Signed-off-by: Danny Nold <dannynold@freescale.com>

based on the 2.6.38 kernel mainline, refer to linux lm-sensors
architeture, add the standalone ahci temperature monitor driver
on fsl i.mx53 platforms.
Less than half sencond is used in one temperature read operation.

usage:
Use the following cmd to cat the i.mx53 soc temperature after
boot up i.mx53 system in user space.
for example:
...$ cat /sys/class/hwmon/hwmon1/device/temp1_input
61000
or run the following cmd after configure the lm-sensors
...$ sensors
imx-ahci-hwmon-isa-0000
Adapter: ISA adapter
temp1:        +58.0 C

Signed-off-by: Richard Zhu <r65037@freescale.com>

- Ported MAX17135 MFD core driver to 2.6.38
- Ported MAX17135 HWMON temperature sensor driver to 2.6.38
- Ported MAX17135 regulator driver to 2.6.38

Signed-off-by: Danny Nold <dannynold@freescale.com>

Fix da9053 backlight Kconfig error
porting da9052 regulator driver

Signed-off-by: Zhou Jingyu <Jingyu.Zhou@freescale.com>
Acked-by: Lily Zhang <r58066@freescale.com>

Add mma8450 accelerometer driver.

Signed-off-by: Sammy He <r62914@freescale.com>

Add mma8451 accelerometer driver.

Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
Signed-off-by: Sammy He <r62914@freescale.com>

The F71869A is almost the same as the F71869F/E, except that it has
the normal number of temp and pwm zones for a F71882FG derived chip,
rather then the limited number of the F71869F/E.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Max Baldwin <archerseven@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This is a new driver for the SMSC EMC6W201 hardware monitoring device.
The device is functionally close to the EMC6D100 series, but is
register-incompatible.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Harry G McGavran Jr <w5pny@arrl.net>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

The abituguru drivers are only built on X86, where DMI support is now
enabled by default. So let these drivers depend on DMI, for the
following gains:
* Robustness and safety. Detection of these devices is weak and uses
  non-standard methods, it should really be limited to Abit boards
  unless the user explicitly asks otherwise.
* Code simplicity. The code is easier to read without ifdefs.
* Better build testing coverage. Now there's only one way to build the
  drivers, so no risk of build failure on exotic systems.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Alistair John Strachan <alistair@devzero.co.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>