linux-toradex.git/drivers/i2c, branch v3.2.48

i2c: designware: always clear interrupts before enabling them

2013-05-30T13:35:02+00:00

commit 2a2d95e9d6d29e726cc294b65391917ed2e32bf4 upstream.

If the I2C bus is put to a low power state by an ACPI method it might pull
the SDA line low (as its power is removed). Once the bus is put to full
power state again, the SDA line is pulled back to high. This transition
looks like a STOP condition from the controller point-of-view which sets
STOP detected bit in its status register causing the driver to fail
subsequent transfers.

Fix this by always clearing all interrupts before we start a transfer.

Signed-off-by: Mika Westerberg 
Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings

i2c: xiic: must always write 16-bit words to TX_FIFO

2013-05-13T14:02:24+00:00

commit c39e8e4354ce4daf23336de5daa28a3b01f00aa6 upstream.

The TX_FIFO register is 10 bits wide.  The lower 8 bits are the data to be
written, while the upper two bits are flags to indicate stop/start.

The driver apparently attempted to optimize write access, by only writing a
byte in those cases where the stop/start bits are zero.  However, we have
seen cases where the lower byte is duplicated onto the upper byte by the
hardware, which causes inadvertent stop/starts.

This patch changes the write access to the transmit FIFO to always be 16 bits
wide.

Signed off by: Steven A. Falco 
Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings

i2c: tegra: check the clk_prepare_enable() return value

2013-03-27T02:41:23+00:00

commit 132c803f7b70b17322579f6f4f3f65cf68e55135 upstream.

NVIDIA's Tegra SoC allows read/write of controller register only
if controller clock is enabled. System hangs if read/write happens
to registers without enabling clock.

clk_prepare_enable() can be fail due to unknown reason and hence
adding check for return value of this function. If this function
success then only access register otherwise return to caller with
error.

Signed-off-by: Laxman Dewangan 
Reviewed-by: Stephen Warren 
Signed-off-by: Wolfram Sang 
[bwh: Backported to 3.2:
 - Adjust context
 - Keep calling clk_enable() directly]
Signed-off-by: Ben Hutchings

i2c-i801: Add Device IDs for Intel Lynx Point-LP PCH

2012-09-19T14:05:02+00:00

commit 4a8f1ddde942e232387e6129ce4f4c412e43802f upstream.

Add the SMBus Device IDs for the Intel Lynx Point-LP PCH.

Signed-off-by: James Ralston 
Signed-off-by: Jean Delvare 
Signed-off-by: Ben Hutchings

i2c-i801: Add device IDs for Intel Lynx Point

2012-09-19T14:05:02+00:00

commit 062737fb6d90c632439b1f77ad6a4965cfc84a20 upstream.

Add the SMBus controller device IDs for the Intel Lynx Point PCH.

Signed-off-by: Seth Heasley 
Signed-off-by: Jean Delvare 
Signed-off-by: Ben Hutchings

i2c-designware: Fix build error if CONFIG_I2C_DESIGNWARE_PLATFORM=y && CONFIG_I2C_DESIGNWARE_PCI=y

2012-09-19T14:04:45+00:00

commit e68bb91baa0bb9817567bd45d560919e8e26373b upstream.

This patch adds config I2C_DESIGNWARE_CORE in Kconfig, and let
I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI select I2C_DESIGNWARE_CORE.

Because both I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI can be built as
built-in or module, we also need to export the functions in i2c-designware-core.

This fixes below build error when CONFIG_I2C_DESIGNWARE_PLATFORM=y &&
CONFIG_I2C_DESIGNWARE_PCI=y:

  LD      drivers/i2c/busses/built-in.o
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_clear_int':
i2c-designware-core.c:(.text+0xa10): multiple definition of `i2c_dw_clear_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x928): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_init':
i2c-designware-core.c:(.text+0x178): multiple definition of `i2c_dw_init'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x90): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_readl':
i2c-designware-core.c:(.text+0xe8): multiple definition of `dw_readl'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_isr':
i2c-designware-core.c:(.text+0x724): multiple definition of `i2c_dw_isr'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x63c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer':
i2c-designware-core.c:(.text+0x4b0): multiple definition of `i2c_dw_xfer'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c8): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_is_enabled':
i2c-designware-core.c:(.text+0x9d4): multiple definition of `i2c_dw_is_enabled'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8ec): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_writel':
i2c-designware-core.c:(.text+0x124): multiple definition of `dw_writel'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer_msg':
i2c-designware-core.c:(.text+0x2e8): multiple definition of `i2c_dw_xfer_msg'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x200): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_enable':
i2c-designware-core.c:(.text+0x9c8): multiple definition of `i2c_dw_enable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8e0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_read_comp_param':
i2c-designware-core.c:(.text+0xa24): multiple definition of `i2c_dw_read_comp_param'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x93c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable':
i2c-designware-core.c:(.text+0x9dc): multiple definition of `i2c_dw_disable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8f4): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_func':
i2c-designware-core.c:(.text+0x710): multiple definition of `i2c_dw_func'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x628): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable_int':
i2c-designware-core.c:(.text+0xa18): multiple definition of `i2c_dw_disable_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x930): first defined here
make[3]: *** [drivers/i2c/busses/built-in.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2

Signed-off-by: Axel Lin 
Signed-off-by: Jean Delvare 
Tested-by: Jiri Slaby 
Signed-off-by: Ben Hutchings

i2c: davinci: Free requested IRQ in remove

2012-05-30T23:44:07+00:00

commit 9868a060ccf769c08ec378a9829137e272e9a92c upstream.

The freed IRQ is not necessary the one requested in probe.
Even if it was, with two or more i2c-controllers it will fails anyway.

Signed-off-by: Marcus Folkesson 
Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings

i2c: tegra: notify transfer-complete after clearing status.

2012-05-30T23:44:07+00:00

commit c889e91d2cc22123f20f40dde0c0a91856a20eea upstream.

The notification of the transfer complete by calling complete()
should be done after clearing all interrupt status.
This avoids the race condition of misconfigure the i2c controller
in multi-core environment.

Signed-off-by: Laxman Dewangan 
Acked-by: Stephen Warren 
Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings

i2c-eg20t: change timeout value 50msec to 1000msec

2012-05-30T23:43:56+00:00

commit 8a52f9f347da721b199b7f9dcc0168bbe7d0baae upstream.

Currently, during i2c works alone, wait-event timeout is not occurred.
However, as CPU load increases, timeout occurs frequently.
So, I modified like this patch.
Modifying like this patch, I've never seen the timeout event with high
load test.

Signed-off-by: Tomoya MORINAGA 
Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings

i2c: pnx: Disable clk in suspend

2012-05-11T12:14:53+00:00

commit 6c557cfee08751d22aed34840f389b846f0f4508 upstream.

In the driver's suspend function, clk_enable() was used instead of
clk_disable(). This is corrected with this patch.

Signed-off-by: Roland Stigge 
Reviewed-by: Arnd Bergmann 

[wsa: reworded commit header slightly]

Signed-off-by: Wolfram Sang 
Signed-off-by: Ben Hutchings