Jonathan writes:

First set of IIO fixes for the 5.4 cycle.

* adis16400
  - Make sure to free memory on a few failure paths.
* adxl372
  - Fix wrong fifo depth
  - Fix wrong indexing of data from the fifo.
  - Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
  - This is a fix for a fix.  The original fix made sure we kept the
    configuration from some firmwares to preserve a bias current.
    Unfortunately it appears the previous behaviour was working around
    a buggy firmware by overwriting the wrong value it had.  Hence
    a regression was seen.
* bmc150
  - Fix the centre temperature.  This was due to an error in one of the
    datasheets.
* hx711
  - Fix an issue where a badly timed interrupt could lead to a control
    line being high long enough to put the device into a low power state.
* meson_sar_adc
  - Fix a case where the irq was enabled before everything it uses was
    allocated.
* st_lsm6dsx
  - Ensure we don't set the sensor sensitivity to 0 as it will force
    all readings to 0.
  - Fix a wait time for the slave i2c controller when the accelerometer
    is not enabled.
* stm32-adc
  - Precursor for fix. Move a set of register definitions to a header.
  - Fix a race when several ADCs are in use with some using interrupts
    to control the dataflow and some using DMA.
* vcnl4000
  - Fix a garbage of_match_table in which a string was passed instead
    of the intended enum.

* tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
  iio: Fix an undefied reference error in noa1305_probe
  iio: light: opt3001: fix mutex unlock race
  iio: adc: ad799x: fix probe error handling
  iio: light: add missing vcnl4040 of_compatible
  iio: light: fix vcnl4000 devicetree hooks
  iio: imu: st_lsm6dsx: fix waitime for st_lsm6dsx i2c controller
  iio: adc: axp288: Override TS pin bias current for some models
  iio: imu: adis16400: fix memory leak
  iio: imu: adis16400: release allocated memory on failure
  iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
  iio: adc: stm32-adc: move registers definitions
  iio: accel: adxl372: Perform a reset at start up
  iio: accel: adxl372: Fix push to buffers lost samples
  iio: accel: adxl372: Fix/remove limitation for FIFO samples
  iio: adc: hx711: fix bug in sampling of data
  iio: fix center temperature of bmc150-accel-core
  iio: imu: st_lsm6dsx: forbid 0 sensor sensitivity
  iio: adc: meson_saradc: Fix memory allocation order

We need to perform a reset a start up to make sure that the chip is in a
consistent state. This reset also disables all the interrupts which
should only be enabled together with the iio buffer. Not doing this, was
sometimes causing unwanted interrupts to trigger.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e5f ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

One in two sample sets was lost by multiplying fifo_set_size with
sizeof(u16). Also, the double number of available samples were pushed to
the iio buffers.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e5f ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Currently, the driver sets the FIFO_SAMPLES register with the number of
sample sets (maximum of 170 for 3 axis data, 256 for 2-axis and 512 for
single axis). However, the FIFO_SAMPLES register should store the number
of samples, regardless of how the FIFO format is configured.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e5f ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Pull chrome platform updates from Benson Leung:
 "CrOS EC / MFD Migration:
    - Move cros_ec core driver from mfd into chrome platform.

  Wilco EC:
    - Add batt_ppid_info command to Wilco telemetry driver.

  CrOS EC:
    - cros_ec_rpmsg : Add support to inform EC of suspend/resume status
    - cros_ec_rpmsg : Fix race condition on probe failed
    - cros_ec_chardev : Add a poll handler to receive MKBP events

  Misc:
    - bugfixes in cros_usbpd_logger and cros_ec_ishtp"

* tag 'tag-chrome-platform-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
  platform/chrome: cros_usbpd_logger: null check create_singlethread_workqueue
  platform/chrome: cros_ec_chardev: Add a poll handler to receive MKBP events
  platform/chrome: cros_ec_rpmsg: Fix race with host command when probe failed
  platform/chrome: chromeos_tbmc: Report wake events
  mfd: cros_ec: Use mfd_add_hotplug_devices() helper
  mfd: cros_ec: Add convenience struct to define autodetectable CrOS EC subdevices
  mfd: cros_ec: Add convenience struct to define dedicated CrOS EC MCUs
  mfd: cros_ec: Use kzalloc and cros_ec_cmd_xfer_status helper
  mfd / platform: cros_ec: Reorganize platform and mfd includes
  mfd / platform: cros_ec: Rename config to a better name
  mfd: cros_ec: Switch to use the new cros-ec-chardev driver
  mfd / platform: cros_ec: Miscellaneous character device to talk with the EC
  mfd / platform: cros_ec: Move cros-ec core driver out from MFD
  mfd / platform: cros_ec: Handle chained ECs as platform devices
  platform/chrome: cros_ec_rpmsg: Add host command AP sleep state support
  platform/chrome: chromeos_laptop: drop checks of NULL-safe functions
  platform/chrome: wilco_ec: Add batt_ppid_info command to telemetry driver

The center temperature of the supported devices stored in the constant
BMC150_ACCEL_TEMP_CENTER_VAL is not 24 degrees but 23 degrees.

It seems that some datasheets were inconsistent on this value leading
to the error.  For most usecases will only make minor difference so
not queued for stable.

Signed-off-by: Pascal Bouwmann <bouwmann@tau-tec.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

There is a bit of mess between cros-ec mfd includes and platform
includes. For example, we have a linux/mfd/cros_ec.h include that
exports the interface implemented in platform/chrome/cros_ec_proto.c. Or
we have a linux/mfd/cros_ec_commands.h file that is non related to the
multifunction device (in the sense that is not exporting any function of
the mfd device). This causes crossed includes between mfd and
platform/chrome subsystems and makes the code difficult to read, apart
from creating 'curious' situations where a platform/chrome driver includes
a linux/mfd/cros_ec.h file just to get the exported functions that are
implemented in another platform/chrome driver.

In order to have a better separation on what the cros-ec multifunction
driver does and what the cros-ec core provides move and rework the
affected includes doing:

 - Move cros_ec_commands.h to include/linux/platform_data/cros_ec_commands.h
 - Get rid of the parts that are implemented in the platform/chrome/cros_ec_proto.c
   driver from include/linux/mfd/cros_ec.h to a new file
   include/linux/platform_data/cros_ec_proto.h
 - Update all the drivers with the new includes, so
   - Drivers that only need to know about the protocol include
     - linux/platform_data/cros_ec_proto.h
     - linux/platform_data/cros_ec_commands.h
   - Drivers that need to know about the cros-ec mfd device also include
     - linux/mfd/cros_ec.h

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Series changes: 3
- Fix dereferencing pointer to incomplete type 'struct cros_ec_dev' (lkp)
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The KIOX010A and KIOX020A ACPI ids go hand in hand, they are used in
yoga style 2-in-1s, with KIOX010A indicating the KXCJ91008 sensor in the
display of the 2-in-1 and KIOX020A indicating the KXCJ91008 sensor in the
base.

Improve the existing comment on the "KIOX010A" kx_acpi_match table entry
to make clear we are talking about a yoga-style (360 degree hinges) device
here and add a similar comment to the "KIOX020A" entry.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch is removing the buffer allocation at each buffer enable.
We just allocate enough memory in the main structure during probe
to cover maximum size needed (that anyway is pretty small) [16bytes].

Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Not even sure why it was there since the beginning. Just use IRQ
number in the sensor_data struct.

Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>