linux-toradex.git/drivers/iio/gyro, branch v4.4.101

iio: bmg160: reset chip when probing

2017-04-12T10:38:33+00:00

commit 4bdc9029685ac03be50b320b29691766d2326c2b upstream.

The gyroscope chip might need to be reset to be used.

Without the chip being reset, the driver stopped at the first
regmap_read (to get the CHIP_ID) and failed to probe.

The datasheet of the gyroscope says that a minimum wait of 30ms after
the reset has to be done.

This patch has been checked on a BMX055 and the datasheet of the BMG160
and the BMI055 give the same reset register and bits.

Signed-off-by: Quentin Schulz 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: gyro: bmg160: fix endianness when reading axes

2016-04-20T06:42:12+00:00

commit 95e7ff034175db7d8aefabe7716c4d42bea24fde upstream.

For big endian platforms, reading the axes will return
invalid values.

The device stores each axis value in a 16 bit little
endian register. The driver uses regmap_read_bulk to get
the axis value, resulting in a 16 bit little endian value.
This needs to be converted to cpu endianness to work
on big endian platforms.

Fix endianness for big endian platforms by converting
the values for the axes read from little endian to
cpu.

This is also partially fixed in commit 82d8e5da1a33 ("iio:
accel: bmg160: optimize transfers in trigger handler").

Signed-off-by: Irina Tirdea 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: gyro: bmg160: fix buffer read values

2016-04-20T06:42:12+00:00

commit b475c59b113db1e66eb9527ffdec3c5241c847e5 upstream.

When reading gyroscope axes using iio buffers, the values
returned are always 0. In the interrupt handler, the return
value of the read operation is returned to the user instead
of the value read. Return the value read to the user.

This is also fixed in commit 82d8e5da1a33 ("iio:
accel: bmg160: optimize transfers in trigger handler").

Signed-off-by: Irina Tirdea 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

2015-11-05T21:15:12+00:00

Pull spi updates from Mark Brown:
 "Quite a lot of activity in SPI this cycle, almost all of it in drivers
  with a few minor improvements and tweaks in the core.

   - Updates to pxa2xx to support Intel Broxton and multiple chip selects.
   - Support for big endian in the bcm63xx driver.
   - Multiple slave support for the mt8173
   - New driver for the auxiliary SPI controller in bcm2835 SoCs.
   - Support for Layerscale SoCs in the Freescale DSPI driver"

* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
  spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
  spi: pxa2xx: Add support for Intel Broxton
  spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
  spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
  spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
  spi: Add DSPI support for layerscape family
  spi: ti-qspi: improve ->remove() callback
  spi/spi-xilinx: Fix race condition on last word read
  spi: Drop owner assignment from spi_drivers
  spi: Add THIS_MODULE to spi_driver in SPI core
  spi: Setup the master controller driver before setting the chipselect
  spi: dw: replace magic constant by DW_SPI_DR
  spi: mediatek: mt8173 spi multiple devices support
  spi: mediatek: handle controller_data in mtk_spi_setup
  spi: mediatek: remove mtk_spi_config
  spi: mediatek: Update document devicetree bindings to support multiple devices
  spi: fix kernel-doc warnings about missing return desc in spi.c
  spi: fix kernel-doc warnings about missing return desc in spi.h
  spi: pxa2xx: Align a few defines
  spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
  ...

spi: Drop owner assignment from spi_drivers

2015-10-28T01:30:17+00:00

An spi_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Andrew F. Davis 
Acked-by: Jonathan Cameron 
Signed-off-by: Mark Brown

iio: bmg160: Add SPI driver

2015-08-31T16:06:11+00:00

Signed-off-by: Markus Pargmann 
Signed-off-by: Jonathan Cameron

iio: bmg160: Separate i2c and core driver

2015-08-31T16:04:23+00:00

This patch separates the core driver using regmap and the i2c driver
which creates the i2c regmap. Also in the Kconfig file BMG160 and
BMG160_I2C are separate now.

Signed-off-by: Markus Pargmann 
Reviewed-by: Srinivas Pandruvada 
Signed-off-by: Jonathan Cameron

iio: st_sensors: add debugfs register read hook

2015-08-16T09:51:25+00:00

This adds a debugfs hook to read/write registers in the ST
sensors using debugfs. Proved to be awesome help when trying
to debug why IRQs do not arrive.

Signed-off-by: Linus Walleij 
Acked-by: Denis Ciocca 
Signed-off-by: Jonathan Cameron

iio: bmg160: Remove remaining uses of i2c_client

2015-08-16T09:51:23+00:00

Signed-off-by: Markus Pargmann 
Signed-off-by: Jonathan Cameron

iio: bmg160: Use generic dev_drvdata

2015-08-16T09:51:22+00:00

i2c_get_clientdata() is specifically for i2c. Replace it with the
generic dev_get/set_drvdata() to support different protocols.

Signed-off-by: Markus Pargmann 
Reviewed-by: Srinivas Pandruvada 
Signed-off-by: Jonathan Cameron