Jonathan writes:

1st set of IIO new device support, features and cleanup for the 6.5 cycle.

New device support
- honeywell,mprls0025pa
  * New driver and dt-bindings for this series of pressure sensors.
- invensense,mpu6050
  * Add support for ICM 20600 IMU (ID, bindings and device data).
- melexis,mlx90614
  * Add support for mlx90615 Infra Red Thermometer after driver cleanup
    and refactoring to support the differences in this device.
- renesas,x9250
  * New driver and bindings for this quad potentiometer.
- rockchip,saradc
  * Add support for RK3588. Also included is a bunch of refactoring and
    cleanup for that driver.
- rohm,bu27008
  * New driver bindings etc for this 5 photodiode color sensor.
- st,lsm9ds0/st,st-sensors
  * ID added for LSM303D accelerometer and magnetometer including ACPI binding.
- ti,opt4001
  * New driver and bindings for this ambient light sensor.

Features
- core
  * Introduce iio_validate_own_trigger() for cases where a driver can only
    consumer a trigger it registered (detected via same parent device).
    Use it in the kionix,kx022a driver and new rohm,by27008 driver.
- dynaimage,al3320a
  * ACPI binding CALS0001 seen on Lenovo Yoga Table 2 devices.
- kionix,kx002a
  * Enable asynchronous probe.
- rohm,bu27034
  * Enable asynchronous probe.
- ti,tmp006
  * Explicit support for DT including binding documentation.

Cleanups, minor fixes and misc improvements.
- treewide
  * Switch I2C drivers from probe_new() back to probe() - part of the
    long process of getting rid of a parameter from probe()
  * Various whitespace and typo fixes not otherwise called out.
- core
  * industrialio-buffer,Style cleanup.
  * Add documentation to extend_name field of struct iio_chan_spec to
    direct people using it towards the label infrastructure instead.
    extend_name was a design mistake a long time back so directly people
    away from it may be useful.
- adi,ad7606
  * Add HAS_IOPORT dependency to prepare for some Kconfig changes.
- bosch,bma400
  * Drop pointless print of ret in a dev_err_probe() message.
- invensense,icm42600
  * Rework timestamp handling to reduce jitter.
- mediatek,mt7986-auxdac
  * Add DT binding for this part.
- qcom,spmi-vadc
  * Allow for 1/16th prescaling used on a few devices.
  * Various changes to channel labeling and naming, including dropping
    use of fwnode_name which generates odd channel names. Small ABI
    change as a result, but not thought to be a problem for users of this
    platform.
- st,lsm6dsx
  * dt-binding: Use common schema for mount-matrix via a reference.
- st,stm32
  * Add a debug print for when legacy channel config is used.
- ti,palmas-adc
  * Drop unused i2c.h include.

* tag 'iio-for-6.5a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (59 commits)
  dt-bindings: iio: rockchip: Fix 'oneOf' condition failed warning
  dt-bindings: iio: afe: voltage-divider: Spelling s/curcuit/circuit/
  dt-bindings: iio: adc: Add rockchip,rk3588-saradc string
  iio: adc: rockchip_saradc: Use dev_err_probe
  iio: adc: rockchip_saradc: Match alignment with open parenthesis
  iio: adc: rockchip_saradc: Use of_device_get_match_data
  iio: adc: rockchip_saradc: Make use of devm_clk_get_enabled
  iio: adc: rockchip_saradc: Add support for RK3588
  iio: adc: rockchip_saradc: Add callback functions
  iio: temperature: tmp006: Add OF device matching support
  dt-bindings: iio: temperature: Add support for tmp006
  staging: iio: Switch i2c drivers back to use .probe()
  iio: amplifiers: ad8366 Fix whitespace issue
  iio: imu: inv_icm42600: avoid frequent timestamp jitter
  MAINTAINERS: Add ROHM BU27008
  iio: light: ROHM BU27008 color sensor
  iio: kx022a: Use new iio_validate_own_trigger()
  iio: trigger: Add simple trigger_validation helper
  dt-bindings: iio: light: ROHM BU27008
  iio: mlx90614: Add MLX90615 support
  ...

We are currently synchronizing every time the data timestamp with
the IT timestamp, leading to system jitter jamming timestamps.
To fix that and keep it simple, let's just synchronize when the
delta is bigger than the acceptable jitter, and keep
synchronization at the jitter value.

The result is much stable timestamps reflecting better the real
physical value. Example @50Hz delta timestamp,
* before: 20.123ms, 19.721ms, 20.023ms, 20.353ms, 19.821ms, ...
* after: 20.173ms, 20.173ms, 20.173ms, 20.40ms, 20.173ms, ...

Refactorize code and delete the unnecessary handling of multiple
FIFO data.

Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230522093210.817212-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230515205048.19561-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Timestamp reset is not done in the correct place. It must be done
before enabling buffer. The reason is that interrupt timestamping
is always happening when the chip is on, even if the
corresponding sensor is off. When the sensor restarts, timestamp
is wrong if you don't do a reset first.

Fixes: ec74ae9fd37c ("iio: imu: inv_icm42600: add accurate timestamping")
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230509152202.245444-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The Invensense ICM-20600 is a 6-axis MotionTracking device that combines a
3-axis gyroscope and an 3-axis accelerometer. It is very similar to the
ICM20602 imu which is already supported by the mpu6050 driver. The main
difference is that the ICM-20600 has a different WHOAMI value.

Signed-off-by: Hermes Zhang <chenhuiz@axis.com>
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230505054853.2155326-3-chenhuiz@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The lsm303d can be found as ACCL0001 on various Lenovo devices,
including the Lenovo Yoga Tablet 2 1051-F, where I tested this
patch.

Dropped SPI support as per discussion in thread linked below.

Signed-off-by: Marius Hoch <mail@mariushoch.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-5-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The lsm303d is basically the lsm9ds0 without the gyroscope
(which the LSM9DS0 IMU driver doesn't handle), as far as I
can tell.

Signed-off-by: Marius Hoch <mail@mariushoch.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-4-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Pull char/misc drivers updates from Greg KH:
 "Here is the "big" set of char/misc and other driver subsystems for
  6.4-rc1.

  It's pretty big, but due to the removal of pcmcia drivers, almost
  breaks even for number of lines added vs. removed, a nice change.

  Included in here are:

   - removal of unused PCMCIA drivers (finally!)

   - Interconnect driver updates and additions

   - Lots of IIO driver updates and additions

   - MHI driver updates

   - Coresight driver updates

   - NVMEM driver updates, which required some OF updates

   - W1 driver updates and a new maintainer to manage the subsystem

   - FPGA driver updates

   - New driver subsystem, CDX, for AMD systems

   - lots of other small driver updates and additions

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (196 commits)
  mcb-lpc: Reallocate memory region to avoid memory overlapping
  mcb-pci: Reallocate memory region to avoid memory overlapping
  mcb: Return actual parsed size when reading chameleon table
  kernel/configs: Drop Android config fragments
  virt: acrn: Replace obsolete memalign() with posix_memalign()
  spmi: Add a check for remove callback when removing a SPMI driver
  spmi: fix W=1 kernel-doc warnings
  spmi: mtk-pmif: Drop of_match_ptr for ID table
  spmi: pmic-arb: Convert to platform remove callback returning void
  spmi: mtk-pmif: Convert to platform remove callback returning void
  spmi: hisi-spmi-controller: Convert to platform remove callback returning void
  w1: gpio: remove unnecessary ENOMEM messages
  w1: omap-hdq: remove unnecessary ENOMEM messages
  w1: omap-hdq: add SPDX tag
  w1: omap-hdq: allow compile testing
  w1: matrox: remove unnecessary ENOMEM messages
  w1: matrox: use inline over __inline__
  w1: matrox: switch from asm to linux header
  w1: ds2482: do not use assignment in if condition
  w1: ds2482: drop unnecessary header
  ...

Pull spi updates from Mark Brown:
 "A fairly standard release for SPI with the exception of a change to
  the API for specifying chip selects done in preparation for supporting
  devices with more than one chip select, this required some mechanical
  changes throughout the tree which have been cooking in -next happily
  for a while.

  There's also a new API to allow us to support TPM chips on half duplex
  controllers.

  Summary:

   - Refactoring in preparation for supporting multiple chip selects for
     a single device, needed by some flash devices, which required a
     change in the SPI device API visible throughout the tree

   - Support for hardware assisted interaction with SPI TPMs on half
     duplex controllers, implemented on nVidia Tedra210 QuadSPI

   - Optimisation for large transfers on fsl-cpm devices

   - Cleanups around device property use which fix some sisues with
     fwnode

   - Use of both void remove() and devm_platform_.*ioremap_resource()

   - Support for AMD Pensando Elba, Amlogic A1, Cadence device mode,
     Intel MetorLake-S and StarFive J7110 QuadSPI"

* tag 'spi-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (185 commits)
  spi: bcm63xx: use macro DEFINE_SIMPLE_DEV_PM_OPS
  spi: tegra210-quad: Enable TPM wait polling
  spi: Add TPM HW flow flag
  spi: bcm63xx: remove PM_SLEEP based conditional compilation
  spi: cadence-quadspi: use macro DEFINE_SIMPLE_DEV_PM_OPS
  spi: spi-cadence: Add support for Slave mode
  spi: spi-cadence: Switch to spi_controller structure
  spi: cadence-quadspi: fix suspend-resume implementations
  spi: dw: Add support for AMD Pensando Elba SoC
  spi: dw: Add AMD Pensando Elba SoC SPI Controller
  spi: cadence-quadspi: Disable the SPI before reconfiguring
  spi: cadence-quadspi: Update the read timeout based on the length
  spi: spi-loopback-test: Add module param for iteration length
  spi: add support for Amlogic A1 SPI Flash Controller
  dt-bindings: spi: add Amlogic A1 SPI controller
  spi: fsl-spi: No need to check transfer length versus word size
  spi: fsl-spi: Change mspi_apply_cpu_mode_quirks() to void
  spi: fsl-cpm: Use 16 bit mode for large transfers with even size
  spi: fsl-spi: Re-organise transfer bits_per_word adaptation
  spi: fsl-spi: Fix CPM/QE mode Litte Endian
  ...

DSDT ROTM method seen in the wild with SMO8B30 _HID.
Making assumption it is similar to that used for bmc150 plus
information from Darrell that the rotation is out by 90 degrees at boot.

Method (ROTM, 0, NotSerialized)
{
    Name (RBUF, Package (0x03)
    {
        "0 -1 0",
        "1 0 0",
        "0 0 1"
    })
    Return (RBUF) /* \_SB_.PCI0.I2C5.DEV_.ROTM.RBUF */
}

Reported-by: Darrell Kavanagh <darrell.kavanagh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Darrell Kavanagh <darrell.kavanagh@gmail.org>
Link: https://lore.kernel.org/r/20230130201018.981024-3-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>